hygena 462/5670 User manual

HYGENA PAIR OF RETRO CHAIRS
Dimensions
Width - 43.3cm
Depth - 47.5cm
Height - 79.8cm
Issue 1 - 07/10/13
Assembly Instructions -Please keep for future reference 462/5670
Important – Please read these instructions fully before starting assembly If you
need help or have damaged or missing parts, call the Customer Helpline:0345 6400800

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
•Check you have all the
components and tools listed
on the following pages.
•Remove all fittings from the
plastic bags and separate them
into their groups.
•Keep children and animals
away from the work area, small
parts could choke if swallowed.
•During assembly do not stand
or put weight on the product, this
could cause damage.
•Assemble the item as close to
its final position (in the same
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Do not stand on the chair.
•Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
•From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
•To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
•Maximun safe weight of user:
110kgs.
•Make sure you have enough
space to layout the parts before
starting.
•Parts of the assembly will be
easier with 2 people.
•
•Do not use this chair as step
ladder.
•Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
•Regularly check and ensure
that all bolts and fittings are
tightend properly.
Handy Hints

2
Backrest x 2
(39.6 x 14.5cm)
3
Chair frame x 2
(75.6 x 57.5cm)
12
Seat pad x 2 (42.2x39.8cm)
4
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components,
call the Customer Helpline: 0345 6400800
The quantities below are for 2 chairs
underside
A
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Components - Fittings
Please check you have all the fittings listed below
68mm Bolt x 8 50mm Screw x 2
B
26mm Bolt x 8
C
Note: The quantities below are the correct amount to complete the assembly of 2 chairs. In some cases
more fittings may be supplied than are required.
Plain washer x 8
DE
Hex key x 1
Chair frame x 2
(75.6 x 57.5cm)

Assembly Instructions
Step 1
Step 2
2
Attaching chair frame
Attach chair frame
to chair frame as
shown in the figure.
3
1
2
1
4
D
A
Assemble seat pad
Place seat pad 4
upside down on a clean,
Carefully position the
chair frame on the seat
pad and secure using
bolts and plain washers
.
A
D
Note: Do not fully
tighten bolts.

Assembly Instructions
Step 3
Step 4
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400800
Re-thighten all the bolts.
Assembly is complete.
Turn the chair upright.
3
C
C
C
C
B
Assemble backrest to
the chair frame using
screw
Note:
tighten the screws.
C
3
Assemble backrest
Parts of the assembly will
be easier with 2 people.
Fixing chair frames
secure chair
frame and using
screw
21
B
22
22
21
upside down chair on a
clean surface,