hygena 459/1553 User manual

Hygena Cantilever Chair
Assembly Instructions - Please keep for future reference
Issue 1 - 19/09/15
Dimensions
Width - 43cm
Depth - 57.5cm
Height - 103.5cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
459/1553
468/9348
hygena

1
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Unit weight: 6.32 kgs.
• Maximum safe weight of user:
110kgs.
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• Do not stand on the chair.
• Do not use this chair as step
ladder.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.

2
Components - Parts
Please check you have all the parts listed below
If you have damaged or missing components, call the
Customer Helpline: Argos = 0345 640 0800
Backrest
(37 x 68 x 10cm)
1
Seat pad
(43.5 x 43 x 9cm)
2
Leg frame
(41 x 55.5 x 41.5cm)
3
Components - Fittings
Please check you have all the fittings listed below
M8 x 20mm Bolt x 4 M6 x 20mm Bolt x 2 M6 x 12mm Bolt x 2
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
E
Spring Washer x 4
CB
Big allen key x 1
F
Small allen key x 1
G
D
Washer x 4
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105

3
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
Step 1
Attaching backrest
Position the backrest
on the seat frame as
shown and fix through
holes using bolts
,spring washer &
washers .
Tighten bolts using big
allen key .
A
D
E
F
1
3
1
1
3
3
AED
A
ED
A
E
DA
A
ED
AED
E
D
Step 2
Attaching the seat
Place the seat pad
face down on a flat and
raised surface.
Position the assembled
chair frame upside down
on the seat pad as
shown and fix through
holes on the leg frame
and seat pad using
bolts and .
Tighten bolts using small
allen key .
Assembly is complete.
B
G
C
2
3
2
B
B
C
C
C
3
3
3
2
2
2
B