hygena 614/9305 User manual

Assembly Instructions - Please keep for future reference 614/9305
Width:
Depth:
Height:
80 cm
40 cm
80 cm
DIMENSIONS
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Argos Aftersales
Helpline: 0345 640 0800
Issue 1-22/09/2016
hygena
FITZ SIDEBOARD

To reduce the likelihood
of damaging your product,
please ensure that your
power drill is set on a low
torque setting.

Top board
1Side board 2Side board 3Divider 4
Divider
5Back board 6Back board x 2 7Shelf x 2 8
Door
9Door 10 Bottom board 11 Drawer front 12
Drawer side
13 Drawer side 14 Drawer back 15 Drawer bottom 16
Drawer bottom support
17 Leg 18 Leg
( 80 x 40 CM) ( 62 x 40 CM) (62 x 40 CM) (76.9 x 38.4 CM)
(45 x 38.4 CM) (77.9 x 16.5 CM) (38.7 x 46 CM) (37.5 x 36 CM)
(45.2 x 38 CM) (45.2 x 38 CM) (80 x 40 CM) (76.4 x 15.6 CM)
(35 x 12 CM) (35 x 12 CM) (72.2 x 12 CM) (34.8 x 73.2 CM)
(33.8 x 9 CM) (86.5 x 14.5 CM) (86.5 x 14.5 CM)
19

CAMLOCK SCREW (35MM )X 12 CAMLOCK NUT( Ø15MM )X 12
B
CAMLOCK SCREW (25MM )X 8
CA
CAMLOCK NUT( Ø12MM) X 8 WOODEN DOWEL( Ø8 X 30MM )
X 18
E
BOLT ( Ø6 X 12MM ) X 5
FD
BOLT ( Ø6 X 45MM ) X 4 SCREW ( Ø3.5 X 12MM ) X 8
H
SCREW ( Ø3.5 X 16MM ) X 8
IG
SCREW ( Ø3.5 X 30MM ) X 4 HANDLE (294MM) X 3
K
SCREW ( Ø4 X 20MM ) X 6
LJ
HINGE (80 X 62MM) X 4 SCREW ( Ø4 X 16MM ) X 24
N
PIVOT PIN (16MM) X 8
OM
BACK SUPPORT (15 X 10MM) X 8 RUNNER (350MM) X 2
Q
RUNNER ( 350MM) X 2
RP
S
ALLEN KEY (68 X 25MM) X 1 FABRIC STRIP (147 X 25MM ) X 2
T
SCREW ( Ø4 X 12MM ) X 4
U
WALL ANCHOR(Ø5 X 35MM) X 2 SCREW ( Ø5 X 35MM ) X 2
W
WASHER ( Ø5 X 1MM ) X 2
XV
S

Rotate all camlock nuts B
Step 1
Step 2
4
board 2 .
a: Position runner Qon side
board 2 and fix into place using
2 x screw H.
b: Insert 2 x camlock screw A, 2
x wooden dowel Einto side
c: Repeat the above for side
board 3 .
d: Attach side board 2 & 3 to
divider 4 .
Align the arrow on 2 x camlock
nut Bwith the edge of divider 4 .
clockwise for about 1/4 or 1/2 a
turn or until the bolts “connects”
with the screw and is secure.
a: A
Eon
b: Attach divider 5 to divider 4 .
nut Bwith the edge of divider 5 .
Rotate all camlock nuts B
turn or until the bolts “connects”
with the screw and is secure.
c:
Insert 2 x camlock screw
and 2 x wooden dowel
divider 4 .
Align the arrow on 2 x camlock
Slide 2 x back board 7 into
clockwise for about 1/4 or 1/2 a
QQ
RR
23
Q
QQ
QQ
H
H
A
2
3
4
B
E
5
7
7
B
E
A
the assembled section
a:
b:
abc:

Step 3
Step 4
45
11
19
A
B
G
F
E
a:
b:
18
F
a:
bolt F .
b:
section using 4 x bolt .
F
a: Insert 2 x wooden dowel E on
side board 2 & 3
b: Insert 2 x camlock screw A
and 2 x wooden dowel Eon
divider 5
c: Attach bottom board 11 to the
assembled section using 4 x
bolt G.
Align the arrow on 2 x camlock
nut Bwith the edge of divider 5 .
Rotate all camlock nuts B
clockwise for about 1/4 or 1/2 a
turn or until the bolts “connects”
with the screw and is secure.
A
Attach leg 18 to leg 19 using
Attach legs to the assembled

Step 5
Step 6
65
a: Attach 2 x fabric strip Tto top
board 1 using 2 x screw U .
b: Insert 4 x camlock screw Aon
top board 1 .
c:
1
U
T
1
BE
a:
b:
c:
d:
e:
A
PI
x wall support kit I& P.
Secure the back board 7 using 8
A
6
assembled section.
Slide back board 6 into the
d: Insert 4 x wooden dowel Eon
side board 2 & 3
e: Attach top board 1 to the
assembled section.
Align the arrow on 2 x camlock
nut Bwith the edge of side
board 2 & 3 .
Rotate all camlock nuts B
clockwise for about 1/4 or 1/2 a
turn or until the bolts “connects”
with the screw and is secure.

8
8
O
Step 7
Insert 2 x pivot pin
Put 2 x shelf 8 into the
assembled section.
Ointo side
board 2 .
Step 8
Attach 2 x hinge Mto door 9 &
10 using 4 x screw Nfor each
door.
9
10
M
N

Step 9
77
Step 10
9
10
a: Attach door 9 & 10 to the
assembled section using 8 x
screw Nfor each.
b: Attach handle K
Lfor each.
12
14
13
17
D
E
K
L
N
a:
b:
a:
b:
c:
d:
15
16
C
a: Insert 6 x camlock screw C
and 2 x wooden dowel Eon
drawer front 12 .
b: Attach drawer side board 13
& 14 and drawer bottom support
17 to drawer front 12 .
Align the arrow on 2 x camlock
nut D
14 & 17 .
Rotate all camlock nuts D
clockwise for about 1/4 or 1/2 a
turn or until the bolts “connects”
with the screw and is secure.
c: Slide drawer bottom 16 into
the assembled section.
on drawer front 15 .
d: Insert 2 x camlock screw C
C
C
to door 9 &
10 using 2 x screw
with the edge of board 13 ,

8
7
f: R
K
L
Step 11
Please insert the drawer into the
assembled section.
e:
D
J
e: Attach board 15 to the
assembled section using 4 x
screw J.
Align the arrow on 2 x camlock
nut Dwith the edge of drawer
bottom support 17 .
Rotate all camlock nuts D
clockwise for about 1/4 or 1/2 a
turn or until the bolts “connects”
with the screw and is secure.
f: Attach 2 x runner Rto drawer
side 13 & 14 using 2 x screw H
for each.
H
H
R

Step 12
5
a:Fixing to wall
Attach the wall strap kit V, X, W
as shown on the drawing.
Warning:
In order to prevent
overturning this
product must be
used with the wall
attachment advice
provided.
Warning:
Before drilling, check
wall for hidden pipes
and cables.
Note: Wall plugs supplied are
for solid wall only.
The correct type of fixing must
be used for your wall, seek
professional advice if in doubt
X
W
9
V
V W
Assembly is complete.

A Guide to - Wall Mounting & Fixings
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist ftting in this case. For light
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
For use when ftting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
plasterboard. The hammer fxing allows
it to be fxed to the wall rather than the
plasterboard. Always check the fxing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety: Always check the ftting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the ftting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well ftted and are a tight ft in the
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult aqualifed
tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fxings is the
responsibility of the installer.