hygena Tallboy 833/4448 User manual

Tallboy
Dimensions
Width - 35cm
Depth - 30cm
Height - 169.5cm
Important – Please read these instructions fully before starting assembly
Assembly Instructions- please keep for future reference 833/4448
Issue 1 - 26/04/11
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 640 0800

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Care and maintenance
• Check you have all the
components and tools listed on
pages 1 and 2.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp
cloth and mild detergent, do
not use bleach or abrasive
cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
1 Base x 1
(29(w)cm x 28.5(d)cm)
2 Middle shelf x 1
(35(w)cm x 30(d)cm)
3 Bottom left side x 1
(89(h)cm x 28.5(d)cm)
4 Bottom right side x 1
(89(h)cm x 28.5(d)cm)
5 Top left side x 1
(77.5(h)cm x 28.5(d)cm)
6 Top right side x 1
(77.5(h)cm x 28.5(d)cm)
7 Top x 1
(35(w)cm x 30(d)cm)
8 Bottom back panel x 1
(80.2(h)cm x 31(w)cm)
9 Top back panel x 1
(79.2(h)cm x 31(w)cm)
10 Door x 1
(78(h)cm x 28.5(w)cm)
11 Top shelf x 2
(30(w)cm x 28(d)cm)
12 Internal shelf x 2
(30(w)cm x 26(d)cm)
1

Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 0845 640 0800
Please check you have all the ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
A B C D
35mm Male camlock x 20 Large female
camlock x 12
Small female camlock x 8 30mm Wooden dowel x 4
E F G H
14mm Screw x 2 Magnetic catch x 1 10mm Screw x 9 Hinge x 2
I J K L
16mm Screw x 2 Handle x 1 Magentic catch plate x 1 Back panel screw x 22
M N O P
35mm Screw x 4 10mm screw x 1 Safety strap x 1 Shelf bracket x 8
Q R S
35mm Wall screw x 1 Washer x 1 Rawl plug x 1
Tools required
Phillips screwdriver
(medium & large) Drill (for wall drilling only)
Ruler – Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
2

3
Assembly Instructions
Step 1
Fix 4 x large female
camlock B into base 1
as shown.
Step 2
Insert 2 x large female
camlock B into bottom
left side 3 and right
side 4 as shown.
Fix 2 x 35mm male
camlock A into bottom
left side 3 and right
side 4 as shown.
Using Camlocks
Step 1
Connect the male
camlock as directed in
the assembly instructions
using a screwdriver.
Step 2
Insert the female
camlock as shown in the
instructions.
Note: ensure that the
arrow on the top of the
camlock points towards
the entry hole for the
male camlock.
Step 3
Push the male camlock
into the entry hole.
Step 4
Turn the female camlock
clockwise with a
screwdriver.
You should feel a click
when the camlock is
locked in place.
The joint is now secure.
B
1
B
A
34

4
Assembly Instructions
Step 3
Screw 2 x male camlock
A into reverse of drawer
front 13 as shown.
Step 4
Connect hinges B to
top door 5 and bottom
door 6 using 15mm
screws F as shown.
Step 5
Insert 4 x 15mm female
camlock E into under
side of top base 7 as
shown.
Insert 4 x small wooden
dowel D into top shelf
9 as shown.
Assembly Instructions
Step 3
Fix 4 x small female
camlock C into
underside of 2 x top
shelf 11 as shown.
Step 4
Fix 4 x 35mm male
camlock A and 2 x
30mm wooden dowel D
into underside of top 7
as shown.
Step 5
Fix 4 x 35mm male
camlock A and 2 x
30mm wooden dowel D
into underside of middle
shelf 2 as shown.
Connect magnetic catch
F to underside of top
7 using 2 x 14mm
screw E as shown (a:).
Step 6
Insert 2 x large female
camlock B into top left
side 5 and top right
side 6 as shown.
Fix 4 x 35mm male male
camlock A into top left
side 5 and top right
side 6 as shown.
2
A
D
a: F
E
C
11
A
D
7
B
A
5 6

5
Assembly Instructions
Step 6
Connect top base 7
and top shelf 9 to top
right side 2.
Tighten female camlocks
in under side of top base
7 with a screwdriver.
Step 7
Connect top left side 1
to exposed ends of top
base 7 and top shelf
9 as shown
Tighten female camlocks
in under side of top base
7 with a screwdriver.
Step 8
Screw 4 x male camlock
A into the under side of
top 10 as shown.
Step 9
Connect top 10 as
shown.
Tighten female camlocks
with a screwdriver.
Assembly Instructions
Step 7
Connect base 1 to
bottom right side 4
as shown and tighten
the female camlocks in
underside of base with
a screwdriver.
Step 8
Connect bottom left
side 3 to base 1
as shown and tighten
the female camlocks in
underside of base with
a screwdriver.
Set assembly aside until
Step 13.
Step 9
Connect 2 x top shelf
11 to top right side 6
as shown and tighten
the female camlocks in
underside of shelves
with a screwdriver.
3
1
1
4
6
11
11

6
Assembly Instructions
Step 10
Connect top left side 5
to exposed ends of top
shelves 11 as shown
and tighten the female
camlocks in underside
of shelves with a
screwdriver.
Step 11
Fix assembly completed
at Step 10 to middle
shelf 2 as shown using
4 x 35mm screw M.
Note: the male camlocks
and wooden dowels
inserted into middle shelf
2 at Step 5 must be
pointing downwards.
5
11
11
2
M

7
Assembly Instructions
Step 12
Connect top 7 to
assembly completed
at Step 11 as shown.
Tighten the female
camlocks inside the unit
with a screwdriver.
Note: the groove in the
edge of top 7 must be
pointing to the rear.
Step 13
Connect assembly
completed at Step 12 to
assembly completed at
Step 8 as shown.
Tighten the female
camlocks inside bottom
left and bottom right
sides with a screwdriver.
Warning: the
unit is heavy.
Ask someone
to help you with
this step.
7

8
Assembly Instructions
Step 14
Fix bottom back panel
8 and top back panel
9 to the rear of the unit
using back panel screws
L as shown.
8
9
L

9
Assembly Instructions
Step 15
Connect door 10 to the
unit using 2 x hinge H
and 8 x 10mm screw G
as shown (b:).
Connect handle J to
door using 2 x 16mm
bolt I as shown (c:).
Connect catch plate K
to door using 1 x 10mm
screw G.
c:
10
H
G
J
I
I
K
G

10
Assembly Instructions
Step 16
Insert 8 x shelf bracket
P into holes inside
the unit at the desired
heights ensuring
that each set of shelf
brackets are level with
each other.
Set 2 x internal shelf 12
onto shelf brackets as
shown.
P
12
12

11
Assembly Instructions
Step 17
To prevent accidental
toppling it is strongly
recommended to x the
unit to a wall.
Connect safety strap
O to the top of the unit
using 1 x 10mm screw
N.
Fix the other end of the
safety strap to a wall
using 1 x rawl plug S,
1 x washer R and 1 x
35mm wall screw Q.
Note: see the back cover
for more information
on wall mounting and
the suitable use of the
supplied rawl plugs.
Warning:
Before drilling,
check wall for
hidden pipes
and cables.
Warning: the
unit is heavy.
Ask someone
to help you with
this step.
Assembly complete.
O
N
S
R
Q

12

13

LP 056.96.133
A Guide to Wall Mounting & Fixings
IMPORTANT:
When drilling into walls always check that there are no
hidden wires or pipes etc. Make sure that the screws
and wall plugs being used are suitable for supporting
your unit. Consult a qualied tradesperson if you are
unsure.
HINTS:
1) General Rule Always use a larger screw and wall plug if you are not sure.
2) Ensure you use the recommended drill bit to match the wall plug and hole size.
3) Ensure you drill the hole horizontally, do not force the drill or enlarge the holes.
4) Take extra care when drilling high walls, ceilings and ceramic tiles.
Ensure the plus is tting below the ceramic tile to avoid splitting or cracking.
5) Ensure wall plugs are well tted and are a tight t in the drilled hole.
Types of Wall
You can use one of the following
types of wall plug if your walls are
made of brick, breeze block, concrete,
stone,wood or plaster board.
No.1 “ Standard” Wall Plug
General Wall Materials
These come in various sizes and are
made from plastic or sometimes wood
ber.
No.2 “ General Purpose” Wall Plug
Aerated / Breeze Block
Generally aerated blocks should not
be used to support heavy loads, use a
specialist tting in this case.
For light loads, a General Purpose
Plug can be used.
No.3 “ Shield Anchor” Wall Plug
Heavy loads
For use with heavier loads such as TV
& HiFi speakers and satellite dishes
etc.
No.4 “Cavity Fixing” Wall Plug
For use with plaster board partitions
or hollow wooden doors.
No. 5 “ Cavity Fixing - Heavy Duty”
Wall Plug
For use when tting or supporting
heavy loads such aas shelving wall
cabinets, coat racks.
No.6 “Hammer Fixing” Wall Plug
For use with walls stuck with plaster
board. The hammer xing allows it
to be xed to the wall rather than the
plaster board. Always check the xing
is secure to the retaining wall.
CARE AND MAINTENANCE
SAFETY
Always check the tting and
location to ensure your safety in
and around the home.
FITTING
From time to time check the
tting to ensure the wall plugs
or screws do not become loose.
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 640 0800
Home Retail Group, 489-499 Avebury Boulevard, Saxon Gate West, Central Milton Keynes, Bucks, MK9 2NW