hygena Valencia 600mm Wall Cabinet User manual

MADE IN
BRITAIN
Dimensions
Width - 60cm
Depth - 34cm
Height - 72cm
Valencia - 600mm Wall Cabinet
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 4 - 17/08/15
Important - Please read these instructions fully before starting assembly
ALR2662
hygena
656/5738
Issue 2 - 05/08/14 - Replaced Grey and Plum codes with Oak and White HN codes.
633/2899
633/2727
203/9309
633/2813
204/8637
Cabinet
Black Door Pack
Cream Door Pack
Oak Door Pack
White Gloss Door Pack
White HN Door Pack
Issue 3 - 10/02/15 - Hinges changed to Slide-ons with Soft Close fittings.
Updated helpline number.
Issue 4 - 17/08/15 - Changed Hanging Brackets.
End Panels now DPF141B.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 11kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
brackets supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
32
4
Loose Shelf (DPF095A)
(568 x 236mm)
Top/Base Panel (DPF094A)
(569 x 319 mm) x 2
Back Panel (DPF096A)
(579 x 694 mm)
5Valencia Door (DPF148B)
(597 x 716mm)
The front surface
of this door is
protected with a
peel-off film
1End Panel (DPF141B)
(320 x 716 mm) x 2

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 8
C
D
Large locking
nut (F900) x 8
F
G H
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Electric drill
(only use when
drilling into walls)
13mm Screw (F63) x 4
E
19mm Connecting bolt (F461) x 2
25mm Screw (F50) x 4
Connecting Sleeve (F432) x 2
Shelf support (F110) x 4
N
N
a
b
25mm Screw (F132) x 2
Handle (F214) x 1
K
M
L
Hinge Plate
(F574) x 2 Hinge (F316) x 2
Soft Close (F320) x 1
I
Wall bracket (F198) x 2
JHanging bracket
(F181) x 2

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
50%
80%
80%
Choose which way
you would like the
door to open
You can fit the door to
the left side or right side.
If you would like
your door to
open this way,
fit the hinge
plates to the left
end panel
If you would like
your door to
open this way,
fit the hinge
plates to the
right end panel
Step 2
K
Prepare the left end
panel
Refer to step 1 and, if
required, fit 2 hinge
plates onto the left
end panel , orientated
as shown.
Screw 4 metal dowels
into the holes shown on
the left end panel .
Note: Tighten metal
dowels up fully against
the panels.
Fit a hanging bracket
to the left side using
2 screws , making
sure that the hook is
towards the back edge.
1
B
1
J
1
G
B
B
B
B
B
This will be the
left end panel
1
J
K
K
K
G
G

Assembly Instructions
5
Step 3
Step 4
Prepare the base and
top
Insert 4 large locking
nuts into the base
and top as shown.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap 4 wooden dowels
into the base and top
as shown.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
C
C
2
10mm
A
A
2
K
Prepare the right end
panel
Refer to step 1 and, if
required, fit 2 hinge
plates onto the right
end panel , orientated
as shown.
Screw 4 metal dowels
into the holes shown on
the right end panel .
Note: Tighten metal
dowels up fully against
the panels.
Fit a hanging bracket
to the right side using
2 screws , making
sure that the hook is
towards the back edge.
1
B
1
J
1
G
A
A
C
C
C
AA
A
C
2
A
A
C
C
C
AA
A
C
2
B
B
B
B
1
This will be the
right end panel
J
K
K
K
G
G

Finished
front edge
Assembly Instructions
6
Step 5
Join the right side and
base
Push the base onto
the right end panel .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
B
C
2
2
1
C
C
Step 6
2
1
1
2
Fit the top
Push the top onto
the right end panel .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
2
1
C
C
NOTE: Hinge plates are not
shown as you may have
fitted them to the left side.

Assembly Instructions
7
Step 7
Step 8
Fit the back
Slide the back along
the grooves in the top
and base and into
the groove of the right
end panel .
Important: Make sure
that the cut-outs on the
back are at the top of
the assembly.
2
2
14
4
4
2
2
1
C
Fit the left end panel
Push left end panel
onto the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the base and top .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
1
2
2
2
2
C
1
Cut-outs
at the top

I
I
564mm
8
Step 9
18mm
37mm
564mm
18mm
Outline of
the unit
Warning: The
unit is heavy.
Lift with care.
Fit the unit to the wall
If you are joining this unit
to another one, also refer
to step 10.
To fix the unit to the wall,
place the unit in the
required position and
lightly mark the outline of
the top corners of the
unit with a pencil.
Fit the 2 wall brackets
to the dimensions shown
in the top diagram.
The screws and plugs
are not supplied as they
need to be the correct
type to suit your wall.
Place your unit onto the
wall brackets , via the
hanging brackets
which you have fitted to
the sides of the unit.
Use the screw at the top
of the wall brackets to
adjust the height of the
unit.
Finally, pull the unit up
against the wall by
tightening up the bottom
screw in the hanging
brackets .
Warning: Take
care when
drilling the wall
that you do not drill into
any pipes, wires etc. If in
doubt, consult an expert.
I
I
J
1
Assembly Instructions
1
1
I
I
464mm
18mm
37mm
464mm
18mm
Outline of
the unit
Warning: The
unit is heavy.
Lift with care.
1
1
J
J
I
J
To adjust the
height of the
unit on the wall,
turn the top
screw
Pull the unit up against
the wall by tightening
the bottom screw
I I
I I

Assembly Instructions
9
Step 10
5mm
Joining units together
Fittings have been
supplied so you are able
to join units together.
Make sure that your first
unit is level.
Push the other unit up
against first unit and
ensure both units are
level.
Check that the ends are
flush and in line, then
clamp them together.
Using a 5mm drill bit,
drill 2 holes (approximate
positions shown circled)
in the side panel into the
adjoining side panel of
the other unit.
Push the connecting
sleeves into the holes
and then screw the
connecting bolts in
from the other side.
E
F
E
F