hygena 833/4431 User manual

Wall Cabinet
Dimensions
Width - 30cm
Depth - 15cm
Height - 50cm
Important – Please read these instructions fully before starting assembly
Assembly Instructions- please keep for future reference 833/4431
Issue 1 - 23/04/11
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 640 0800

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Care and maintenance
• Check you have all the
components and tools listed on
pages 1 and 2.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp
cloth and mild detergent, do
not use bleach or abrasive
cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
1 Top x 1
(30(w)cm x 15(d)cm)
2 Base x 1
(27(w)cm x 13.5(d)cm)
3 Right side x 1
(47(h)cm x 13.5(d)cm)
4 Left side x 1
(47(h)cm x 13.5(d)cm)
5 Support rail x 1
(24(w)cm x 6(h)cm)
6 Back panel x 1
(47.8(h)cm x 24.8(w)cm)
7 Door x 1
(46.5(h)cm x 23.5(w)cm)
8 Shelf x 1
(23.8(w)cm x 9.8(d)cm)
1

Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 0845 640 0800
Please check you have all the ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
A B C D
35mm Male camlock x 8 Female camlock x 8 16mm Bolt x 2 Handle x 1
E F G H
14mm Screw x 2 Magnetic catch x 1 10mm Screw x 9 Hinge x 2
I J K L
30mm Wooden dowel x 4 Catch plate x 1 Shelf bracket x 4 40mm Wall screw x 2
M N
Washer x 2 Rawl plug x 2
Tools required
Phillips
screwdriver
(medium &
large)
Drill (for wall
drilling only) Spirit level
Ruler – Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
2

3
Assembly Instructions
Step 1
Fix 4 x 35mm male
camlock A into
underside of top 1 as
shown.
Connect magnetic catch
F to underside of top
1 using 2 x 14mm
screw E as shown (a:).
Step 2
Fix 4 x 35mm male
camlock A base 2 as
shown.
Using Camlocks
Step 1
Connect the male
camlock as directed in
the assembly instructions
using a screwdriver.
Step 2
Insert the female
camlock as shown in the
instructions.
Note: ensure that the
arrow on the top of the
camlock points towards
the entry hole for the
male camlock.
Step 3
Push the male camlock
into the entry hole.
Step 4
Turn the female camlock
clockwise with a
screwdriver.
You should feel a click
when the camlock is
locked in place.
The joint is now secure.
1
A
F
E
a:
A
2

4
Assembly Instructions
Step 3
Screw 2 x male camlock
A into reverse of drawer
front 13 as shown.
Step 4
Connect hinges B to
top door 5 and bottom
door 6 using 15mm
screws F as shown.
Step 5
Insert 4 x 15mm female
camlock E into under
side of top base 7 as
shown.
Insert 4 x small wooden
dowel D into top shelf
9 as shown.
Assembly Instructions
Step 3
Insert 2 x 30mm wooden
dowel I into each end
of support rail 5 as
shown.
Step 4
Insert 4 x female
camlock B into right
side 3 and left side 4
as shown.
Step 5
Connect left side
4 and right side 3
to support rail 5 as
shown.
Note: the unit is upside
down at this point.
I
5
3
4
B
4
3
5

5
Assembly Instructions
Step 6
Connect top base 7
and top shelf 9 to top
right side 2.
Tighten female camlocks
in under side of top base
7 with a screwdriver.
Step 7
Connect top left side 1
to exposed ends of top
base 7 and top shelf
9 as shown
Tighten female camlocks
in under side of top base
7 with a screwdriver.
Step 8
Screw 4 x male camlock
A into the under side of
top 10 as shown.
Step 9
Connect top 10 as
shown.
Tighten female camlocks
with a screwdriver.
Assembly Instructions
Step 6
Connect top 1 to
assembly completed
at Step 5 as shown
and tighten the female
camlocks inside the unit
with a screwdriver.
Step 7
Slide back panel 6 into
the slots of left and right
sides and push rmly
down to locate.
Note: the holes in the
back panel should point
downwards at this stage
and should line up with
the holes in support rail
5 when back panel is
fully inserted.
Step 8
Connect base 2 to
the assembly as shown
and tighten the female
camlocks inside the unit
with a screwdriver.
Turn the unit right way
up to complete the
remaining steps.
1
6
5
2

6
Assembly Instructions
Step 9
Connect door 7 to the
unit using 2 x hinge H
and 8 x 10mm screw G
as shown (b:).
Connect handle D to
door using 2 x 16mm
bolt C.
Connect catch plate J
to door using 1 x 10mm
screw G.
Note: catch plate J
must be attached with
the countersink facing
outwards so as to
accommodate the screw
head.
Step 9
Insert 4 x shelf bracket
K into holes inside
the unit at the desired
heights ensuring
that each set of shelf
brackets are level with
each other.
Set shelf 8 onto shelf
brackets as shown.
b:
D
C
J
G
H
G
K
8
7

7
Assembly Instructions
Step 10
Note: you may nd it
easier to have help from
another person at this
stage.
To x the unit to a wall
hold the unit in the
desired position against
the wall, using a spirit
level to ensure the unit is
horizonal/vertical.
Mark the wall through the
holes in the back panel
of the unit to establish
the screw positions.
Set the unit aside and
drill the wall at the
mark locations using an
appropriate drill bit.
Insert 1 x rawl plug N
into each hole.
Screw the unit to the
rawl plug using 2 x
40mm wall screw L
inserted through 2 x
washer M.
Note: see the back cover
for more information
on wall mounting and
the suitable use of the
supplied rawl plugs.
Warning:
Before drilling,
check wall for
hidden pipes
and cables.
Assembly complete.
N
L
M

8