hygena Valencia User manual

MADE IN
BRITAIN
Dimensions
Width - 60cm
Depth - 59cm
Height - 213cm
Valencia - 600mm Larder Cabinet
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 05/08/14
Important - Please read these instructions fully before starting assembly
ALR2657
hygena
633/7777
633/2923
633/2758
198/9405
633/2844
194/7605
If you are fitting a
Fridge/Freezer inside
this unit please refer to
the instructions that
were supplied with the
appliance.
We recommend that you
contact a registered
installer.
05/09/11 - Four SC2777 (F65) screws added to the kit and these are now used to fit the Small Back instead of using 4 of the SC2802’s (F50).
Cabinet
Black Door Pack
Cream Door Pack
Oak Door Pack
White Gloss Door Pack
White HN Door Pack
Issue 3 - 05/08/14 - Replaced Grey and Plum codes with Oak and White HN codes.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 47kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill

Components - Panels
Please check you have all the panels listed below
2
1
80%
x 2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
2
4
3
5
6
7
Loose Shelf (DPF079A)
(568 x 431mm) x 3
Back (DPF109A)
(579 x 1976mm)
Valencia Door (DPF148B)
(597 x 716mm)
8Valencia Larder Door (DPF156B)
(597 x 1258mm)
9
Left Side (DPF106B)
(1980 x 560mm)
Right Side (DPF107B)
(1980 x 560mm)
Fixed Shelf (DPF108B)
(569 x 494mm)
Top/Base (DPF078B)
(569 x 494mm) x 2
Small Back
(D1148)
(164.5 x 570mm)

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 18
B
Metal dowel (F901) x 12
C
D
Large locking
nut (F900) x 12
F
G H I a
I c
I d
I e
I b
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K
13mm Screw (F63) x 10
E
13mm Screw (F79) x 2
Connecting Sleeve (F432) x 2 19mm Connecting bolt (F461) x 2
L M
25mm Screw (F50) x 9
N
Hinge Cover (F119) x 5
Bracket (F945) x 2 Shelf support (F110) x 12
Hinge Plate
(F117) x 5
Hinge Arm (F118) x 5
Leg Bracket
(F127) x 2
Leg Socket
(F120) x 4
Leg Clip
(F128) x 2
16mm Screw
(F129) x 16
Leg (F122) x 4
hygena
O
O
a
b
25mm Screw (F132) x 4
Handle (F214) x 2
45mm Screw (F65) x 4
P

4
Step 1
J
E
Step 2
Prepare the left side
Refer to step 1 and, if
required, fit 5 hinge
plates onto the left
side , as shown.
Screw 6 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Fit a bracket
to the left side
using screw ,
flush with the top
edge and back
edge, see
diagram.
B
B
B
B
B
B
B
B
L
L
L
L
L
J
J
1
1
1
1
1
E
Choose which way
you would like the
doors to open
You can fit the doors to
the left side or right side.
Assembly Instructions If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1
L
L
If you would
like your doors
to open this
way, fit the
hinge plates to
the left side
If you would
like your doors
to open this
way, fit the
hinge plates to
the right side
IMPORTANT
Only carry out this step if you are building a Larder Cupboard.
If you are building a housing for a fridge/freezer go to Step 3.

5
Step 3
Step 4
Assembly Instructions
L
J
E
Prepare the right side
Refer to step 1 and, if
required, fit 5 hinge
plates onto the right
side , as shown.
Screw 6 metal dowels
into the holes shown on
the right side .
Fit a bracket to the
right side , flush with
the top edge and back
edge, see diagram.
Secure the bracket
using screw .
2
B
2
J
J
2
E
B
B
B
B
B
B
L
L
L
L
J
2
2
2L
L
J
E
Step 2
Prepare the left side
Refer to step 1 and, if
required, fit 5 hinge
plates onto the left
side , as shown.
Screw 6 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Fit a bracket
to the left side
using screw ,
flush with the top
edge and back
edge, see
diagram.
B
B
B
B
B
B
L
L
L
L
L
J
J
1
1
1
1
1
E
1
L
L
J
E
B
B
B
B
B
L
L
L
L
J
1
1
1
L
L
B
B
IMPORTANT
Only carry out this step if you are building a housing for a
fridge/freezer. If you are building a Larder Cupboard you have
already prepared this panel in Step 2.
B
B
IMPORTANT
Only carry out this step if you are building a Larder Cupboard.
If you are building a housing for a fridge/freezer go to Step 5.

Assembly Instructions
6
Step 5
L
J
E
Prepare the right side
Refer to step 1 and, if
required, fit 5 hinge
plates onto the right
side , as shown.
Screw 6 metal dowels
into the holes shown on
the right side .
Fit a bracket to the
right side , flush with
the top edge and back
edge, see diagram.
Secure the bracket
using screw .
2
B
2
J
J
2
E
B
B
B
B
L
L
L
L
J
2
2
2L
L
IMPORTANT
Only carry out this step if you are building a housing for a
fridge/freezer. If you are building a Larder Cupboard you have
already prepared this panel in Step 4.
A
A
A
A
A
A
C
C
C
C
A
A
A
A
A
A
C
C
C
Prepare the base and
top
Insert 4 large locking
nuts into the base
and top as shown.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap 4 wooden dowels
into the base and top
. as shown.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
C
C4
4
10mm
A
A
4
4
Step 6
4
4
C
B
B

Assembly Instructions
7
Step 7
Finished
front edge
Finished
front edge
Join the base and top
to the right side
Push the top and
base onto the right
side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top and base .
Note: Turn the large
locking nuts as far
as they will go - more
than 1/2 a turn.
4
4
44
2
C
C
Step 8
B
C
4
4
2
I a
I b
b: c: d:
Fit the legs to the
base
a: Push the leg sockets
. into the holes in the
base as shown.
b: Secure each leg
socket with 3
screws .
c: Tap in the centre plug
on each leg socket .
d: Push the leg into
the leg socket .
I a
I a
I a
I e
I e
4
x 3
I a
I a
I b
I a
I a
I a
4
I a
NOTE: Hinge plates
are not shown as
you may have fitted
them to the left side.
If you are building a
housing for a
fridge/freezer these
2 metal dowels...
...will be here

A
A
A
Assembly Instructions
8
Step 9
Step 10
Finished
front edge
Fit the fixed shelf
Push the fixed shelf
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the fixed shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
6
2
C
C
2
6
6
A
A
A
C
C
C
C
Prepare the fixed
shelf
Insert 4 large locking
nuts into the fixed
shelf as shown.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap 6 wooden dowels
into the fixed shelf .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
C
6
A
6
6
If you are building a
housing for a
fridge/freezer this
fixed shelf...
...must be fitted here

9
Assembly Instructions
Step 11
Fit the small back
Position the small back
. between the top
and fixed shelf , as
shown and secure it into
position using 4 screws
. .
2
6
P
P
IMPORTANT
Only carry out this step if you are building a housing for a
fridge/freezer. If you are building a Larder Cupboard please
ignore this step.
9
4
Step 12
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the large locking
nuts fitted to the
base , top and
fixed shelf .
Note: Turn the
large locking
nuts as far
as they will go
- more than
1/2 a turn.
6
6
1
C
C
4 4
4
4
1
If you are building a
housing for a
fridge/freezer this
fixed shelf...
...will be fitted here
P
P
94
6
P