Hytronik HEC7028 User manual

Instruction Manual for Integrated SensorDIM LED Driver
Daylight Monitoring Version, Model No.:HEC7028
Technical Specifications
PRODUCT TYPE: Integrated sensorDIM LED driver
OPERATING VOLTAGE: 220-240VAC 50/60Hz
HF SYSTEM: 5.8GHz CW radar
TRANSMISSION POWER: <0.2mW
DETECTION ANGLE: 30 ~150
DETECTION RANGE: Max. 8 meters in diameter, adjustable
TIME SETTING: 2s, 30s~30min.
DAYLIGHT SENSOR: 2~50Lux; disable
STAND-BY PERIOD: 0s, 10s ~ +∞
STAND-BY DIMMING LEVEL: 10% ~30%
MOUNTING: Indoors, ceiling&wall mounted
INSTALLATION HEIGHT: ≤5M
WORKING TEMP.: -20~+50℃
°
°
This is a smart integration of microwave motion sensor and multiple
current selection LED driver, which gives pre-selected constant current
to drive the LEDs to work based upon movement detection. Designed
in the software and thanks to our worldwide patented circuit, the built-in
daylight sensor is prior to motion sensor so as to achieve utmost energy saving purpose.
Note: the high-frequency output of this sensor is <0.2mW; approximately just 1‰ of the transmission power of a mobile telephone or
the output of a microwave oven.
Daylight sensor
Cut-out size (L x D: 36 x 29.5mm)
Buzzer
L (Blue)
N (Brown)
Installation hole (4.1mm)
Installation hole
(screw D x L: 3 x 10mm)
Sensor antenna
LED current selection
LED
LED indication
Infrared remote receiver
Rotary switch
LED
HRC-05
HEC7028
Stand-by dimming level
Detection range
ON/
OFFAuto ModeReset
Power
80%
Test
2s
10%20%
30s 1min
100%
30min10min5min
0s 10s1min
30%
SC1SC2
SC3
Scene mode
10min
50%10%
30min
Hold-time
Stand-by period
5min
Lux
Disable
2Lux
10Lux
50Lux
DaylightSensor
SC4
Power
100% +
-
Dim
M/A
110
101.1
35.5 4.1
49.534.7
23.7 31.6
29
IMPORTANT
PLEASE READ THESE INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION AND RETAIN THIS LEAFLET IN A KNOWN
AND SAFE PLACE FOR FUTURE REFERENCE.
SECTION 1 INSTALLATION AND WIRING
1.1 Ensure that the electricity supply is switched off before installing or servicing this product.
1.2 Wiring diagram
LED
LED
N
N
L
L
+
-
3rd Floor, block C, complex building, 155#, Bai'gang road south,
Bai'gang village, Xiao Jin Kou town, Huicheng district, Huizhou 516023
Tel:[phone] F:86-752-2777877
E: [email protected] W:www.hytronik.com
CHINA FACTORY
Room D, 10/f, Tower A, Billion Center, 1 wang Kwong Road,
Kowloon Bay, Kowloon, Hongkong
T: 00852-35197525 F: 00852-30116936
E: [email protected]
HYTRONIK INDUSTRIAL LIMITED

SECTION 2 FUNCTION
This multiple current LED driver has a wide range of loading capacity:
Maximum load @ different currents:
Maximum voltage @ different currents:
3.5~17W (350mA) 5~24W (500mA) 5.5~25W (550mA)
7~28W (700mA) 7~28W (750mA) 9~28W (900mA)
10~48V (350mA) 10~48V (500mA) 10~46V (550mA)
10~40V (700mA) 10~37V (750mA) 10~31V (900mA)
Current
350mA
500mA
550mA
700mA
750mA
900mA
1 2 3
The current can be easily configured by choosing
the correct combination of the DIP switches (see
table on the left).
2.1 LED Current Selections
2.2 LED Maximum Load and Voltage
2.3 Settings (Rotary Switch on Sensor Antenna)
Channel Detection range Hold-time Daylight sensor Stand-by period Stand-by dimming level
0 100% 5s Disable 10s 10%
1 100% 30s 2Lux 1min 10%
2 100% 1min 2Lux 5min 10%
3 100% 1min 10Lux 10min 10%
4 100% 1min Disable +∞ 10%
5 100% 5min 2Lux 10min 10%
6 100% 5min 10Lux 30min 10%
7 100% 5min Disable +∞ 10%
8 100% 10min 2Lux 10min 10%
9 100% 10min 10Lux 30min 10%
A 100% 10min Disable +∞ 10%
B 50% 10min Disable 30min 10%
C 10% 10min Disable 10min 10%
D 100% 30min 10Lux 30min 10%
E100% 30min Disable +∞ 10%
F100% 5s 2Lux 10s 10%
2.4 Assembly
Note: end-user can also scan the QR
code on the housing for checking settings.
The sensor antenna features the rotary
switch and protrudes the LED panel.
This feature enables the end user to
access the sensor settings without
removing the gear tray / LED board.
Cut-out size: 36 x 29.5 (mm)
Sensor antenna

Detection range[ ]
Press buttons in zoneto set detection range at 100% / 50% / 10%.
Hold time [ ]
Press buttons in zoneto set hold time at 30s / 1min / 5min / 10min / 30min.
Stand-by period [ ]
Press buttons in zoneto set stand-by period at 0s / 10s / 1min / 10min / 30min / +∞.
Note: “0s” means on/off control; “+∞” means bi-leve of dimming control, light never switches off.
Stand-by dimming level [ ]
Press buttons in zoneto set the stand-by dimming level at 10% / 20% / 30% .
Daylight sensor []
Press buttons in zone to set daylight sensor at 2lux / 10lux / 50lux.
6
11
13
12
7
M/A [ ]
Note: this button is disabled.
button
15
zone 6
zone
11
zone
12
zone
7
zone 13
SECTION 3 REMOTE CONTROL
Permanent ON/OFF [ ]
1. Press button , the light goes to permanent ON or permanent OFF mode.
2. Press button to quit from this mode.
3. The mode will change to AUTO Mode after power failure.
(
Please refe
r
to explanation accordingly)
Auto Mode [ ]
Press button goes to auto mode, the sensor starts working and all settings remain the same as the latest status before the light was switched ON/OFF.
RESET [ ]
Press button , all settings go back to the value of rotary switch.
Test 2s function [ ]
1. Press button , the sensor goes to test mode(hold time 2s), stand-by period and daylight sensor are disabled.
2. Press button to quit from this mode, and the sensor setting is changed accordingly.
Ambient daylight threshold [ ]
Press button , the latest surrounding lux value overwrites previous lux value learend, and is set as the daylight threshold. This feature enables the fixture
to function well in any real application circumstance.
1
2
3
234
button 1
button 2
button 3
8
3
10
4
11
button 8
button
10
Power output [ ]
Press button , the output shifts between 80% (at initial 10,000 hours) and 100%, for energy saving purpose.
5
button 5
Dim +/- [ ]
Press button to adjust the light brightness between 10%~100% during hold-time.“+” means dimming up, “-” means dimming down.
9
button 9
Lux disable [ ]
Press button , the built-in daylight sensor stops working, and all motion detected could turn on the lighting fixture, no matter how bright the natural light is.
14
button
14
5
9
4
11
12
Stand-by dimming level
Detection range
ON/
OFFAuto ModeReset
Power
80%
Test
2s
10%20%
30s 1min
100%
30min10min5min
0s 10s1min
30%
SC1SC2
SC3
Scene mode
10min
50%10%
30min
Hold-time
Stand-by period
5min
Lux
Disable
2Lux
10Lux
50Lux
Daylight Sensor
SC4
Power
100% +
-
Dim
M/A
3
1
2
7
8
6
10
13
14
15
HRC-05
Note: the buzzer beeps one time when RC
receives signal successfully

SECTION 4 TROUBLE SHOOTING
YDEMERESUACYDEMERESUACNOITCNUFLAM
Incorrect light-control setting selected Adjust setting
daolecalpeRytluafdaoL
The load will not work
NOhctiwSFFOhctiwssniaM
The load is always on Continuous movement in the detection zone Check zone setting
The sensor is not mounted for reliably detecting
movementSecurely mount enclosure
The load is on withoutanyidentifiable
movementMovement occurred, but not identified by the sensor
(movement behind wall, movement of small object in
immediate lamp vicinity etc.)
Check zone setting
The load will not work despite movement Rapid movements are being suppressed to minimise
malfunctioning or the detection radius is too small Check zone setting
Scene mode options [ ]
Note:end-user can adjust the settings by pressing buttons of detection range / hold time / stand-by period / stand-by dimming level
/daylight sensor , the last setting stays in validity.
611
13
12
7
zone 4
There are 4 scene modes built-in the remote control for different applications:
Scene options Detection range Hold time Stand-by period Stand-by dimming leve Daylight sensor
SC1 100% 1min 10min 10% 2Lux
SC2 100% 5min 10min 10% 2Lux
SC3 100% 10min 30min 10% 10Lux
SC4 100% 10min + 10% 50Lux
8