Hytronik HIM31 Quick guide

1. Technical Specifications
Product type Tri-level control dual sense sensor
Operating voltage 220-240VAC 50/60Hz
800VA(Capacitive)
1000W(Resistive)
Power consumption < 1W
Detection angle 360o
Detection area (Max.)*
Detection range 10% / 50% / 75% / 100%
Hold time 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min
Stand-by time 0s / 10s / 1min / 5min / 10min / 30min / 1h / + ∞
Stand-by dimming level 10% / 20% / 30% / 50%
Daylight threshold 2 ~ 500Lux, Disable
Warmming up time 30s
Operating temperature -20oC ~ +50oC
IP rating IP65
Sensor mode HF, PIR, HF+PIR, HF / PIR
2. Rotary Switch Settings
A rotary switch is built inside the sensor for
scene selection / fast programming. Total of
16 channels available:
Note: settings can also be changed by remote control HRC-11. The last action controls.
Detection
range
Channel
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
75%
50%
100%
100%
100%
5s
1min
5min
5min
5min
5min
5min
10min
10min
10min
10min
10min
10min
30min
30min
5s
10s
5min
10min
30min
0s
+∞
+∞
10min
30min
+∞
+∞
+∞
+∞
+∞
+∞
10s
10%
10%
10%
10%
Disable
10%
30%
10%
10%
10%
30%
10%
10%
10%
30%
10%
Disable
2Lux
10Lux
30Lux
10Lux
30Lux
Disable
2Lux
10Lux
30Lux
Disable
30Lux
10Lux
50Lux
Disable
2Lux
Hold
time
Stand-by
time
Stand-by
dimming level
Daylight
threshold
3. Functions
Hytronik builds this function inside the motion sensor to achieve tri-level control, for some areas it requires
a light change notice before switch-off.
It offers 3 levels of light: 100%-->dimmed light-->off; and 2 periods of selectable waiting time: motion
hold-time and stand-by period; Selectable daylight threshold and freedom of detection area.
The built-in daylight sensor can read ambient natural light and switch off the fixture automatically
whenever artificial light is unnecessary (natural light lux level exceeds daylight threshold).
Note: if the stand-by time is preset at "+∞", the fixture never switches off even when natural light
is sufficient.
3.1 Tri-level Control (Corridor Function)
3.2 Lux Off Function
HIM31-20230620-A1
Rated load
The light will flash ONCE rapidly after receiving the command from the remote controller.
Note: There is no load indication (the light will not flash) when button ON/OFF, POWER 100%
or POWER 80% is pressed.
3.3 Load Indication
4. Installation
Warnings:
1. Installation of the sensor involves connecting it to the mains supply. This work must be
carried out by a specialist in accordance with electrotechnical regulations.
2. Disconnect power supply before installing.
5. Wiring Diagram
HIM31
Brown
LED driver
L
N
1-10V+
1-10V-
L
N
Blue
Grey
Red
Black
Installation and Instruction Manual
HIM31
HIGH BAY DUAL SENSE SENSOR
———This product should be installed by a qualified electrician.
Note:We recommend the mounting distance between sensor to sensor
should be more than 2m to prevent sensors from false-triggering.
A. Ceiling mount
B. Screw to the Luminaire by conduit
C. Attach to the shade by clamp
HIM31-20230620-A1
Rotary switch preset (Please
see the location in 2. Installation)
Max installation height：15m (forklift)/12m (human)
Max detection range：
HF: Ø = 24m (forklift)/14m (human)
PIR: Ø = 24m (forklift)/20m (human)
12
6. Three Options for PIR Lens and Detection Patterns
(End user can choose the suitable lens in real application for various requirements)
* For single person walking across, the detection range is reduced by 1/3.
3
Detection pattern for human
PIR detection: Ø = 24m (max.)
HF detection: Ø = 24m (max.)
PIR detection: Ø = 24m (max.)
HF detection: Ø = 24m (max.)
PIR detection: Ø = 24m (max.)
HF detection: Ø = 24m (max.)
Detection pattern for forklift
15m(forklift)
PIR & HF: max. 24m
PIR
HF
PIR & HF: max. 24m
PIR
HF
15m(forklift)
PIR & HF: max. 24m
PIR
HF
15m(forklift)
HF detection: Ø = 14m (max.)
PIR detection: Ø = 20m (max.)
HF detection: Ø = 14m (max.)
PIR detection: Ø = 20m (max.)
HF detection: Ø = 14m (max.)
PIR detection: Ø = 20m (max.)
PIR
HF
PIR: max. 20m
HF: max. 14m
12m(human)
PIR
HF
PIR: max. 20m
HF : max. 14m
12m(human)
PIR
HF
PIR: max. 20m
HF: max. 14m
12m(human)
81.5
4.1
66.6
91.5
80.7
75
4.1
Sensor module
PIR
Daylight sensor
LED indicator Infrared receiver
Rotary switch for programing
Cable entry
Installation rack
Cable entry
Sensor module
PIR
Daylight sensor
LED indicator Infrared receiver
Rotary switch for programing
59.6
66.6
89.9
0.825”
75
64
43.8
43
163.2
33.7
28.5
4.5
15
96.8
66.6
ぶ
4.5
93.8
84.5
59.3
ぶ
29
Sensor module
PIR
Daylight sensor
LED indicator Infrared receiver
Rotary switch for programing
Angle adjustment
Luminaire clamp
73.5
59.3 57.3
47.5
73.5
59.3
57.3
47.5
24.5

HIM31-20230620-A1 HIM31-20230620-A1
HRC-11
Sensor off Twilight
Shift
AUTO
100% 75% 50% 10%
2 Lux
100 Lux
10 Lux
300 Lux
50 Lux
500 Lux
Disable
Ambient
Memory Apply
Test
2 s
30 s
1 min 10 min
5 min 15 min 30 min
0s
10 s 1h
10% 20% 30% 50%
Dual tech & RF mode
SEMI-AUTO
Hold-time
Stand-by time
Stand-by dimming level & Auto-config.
Daylight threshold
Sensitivity & More functions
RX STBY%
PIR
RX 100%
HF HF+PIR HF/PIR
Shift Send
5 min 30 min
20 min
Power
100%
Power
80%
1 min 10 min +
Start
RESET
ON
OFF
24h 30s
12h 4h
Learn
Erase Transmit
Brightness
CCT-
CCT+
Tri-level Harvest Master ×
Exp 1 Exp 2 Lux off
In AUTO /SEMI-AUTO modes, press buttons in zone “hold-time” to set the hold-time at 2s
/ 30s / 1min / 5min / 10min / 15min / 20min / 30min.
Dual tech & RF mode
Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min
/ 10min / 30min / 1h / +∞.
Note: 1. To set stand-by-time at 10s/ 5min / 30min / 1h, press “Shift” button rst.
2. “0s” means on/off control;
3. “+∞” means bi-level control, the xture is 100% on when there is motion detected, and remains at the
stand-by dimming level when no presence after motion hold-time. Only when the stand-by time is set in "+∞" and
the ambient lux level is below the target lux level, the lux will auto-on.
Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10%
/ 20% / 30% / 50%.
Press buttons in zone “Daylight threshold” to set daylight sensor at 2Lux/ 10Lux / 50Lux
/ 100Lux / 300Lux/500Lux / Disable.
1. Press button “Shift”, the red LED on.
2. Press button “Ambient”, the surrounding lux level is sampled and set as daylight threshold
/ target Lux level.
In AUTO /SEMI-AUTO modes, press buttons in zone “Detection range” to set
detection range at 100%/75%/50%/10%.
Note: To set daylight sensor at 100Lux / 300Lux/500Lux , press “Shift” button rst.
Master
100% 75%
50% 10%
Tri-level
Harvest
2 Lux 100 Lux
10 Lux 300 Lux
50 Lux 500 Lux
Disable
Ambient
Test
2 s
30 s
1 min
10 min
5 min
15 min
30 min
20 min
0s 10 s
1h
5 min
30 min
1 min
10 min
+
10% 20%
30% 50%
24h
30s
12h
4h
PIR
HF
HF+PIR
HF/ PIR
Learn
Erase
Transmit
Note: 1. To set hold-time at 30s / 5min / 15min / 30min, press “Shift” button rst.
2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.
*To exit from Test mode, press button “RESET” or any button in “Hold-time”.
Short press”learn/erase” button to activate pairing mode, then press ”transmit” on a
primary mode and all the receiver modules will beep 3 times in 1s to indicate the
success of paring. Long press the “learn/erase” button for 3s will erase all the commands
received previously.
Press button RX100%, the light on receiver unit is 100% upon receiving RF on singal;
Press button “RX STBY%”, the light(s) oes to pre-set stand-by dimming level directly.
1.Press button “Shift” ,the red LED on.
2. Choose one of the four detecion mode “HF only”, “PIR only”, “HF& PIR” or“ HF/PIR”.
Stand-by time mode
Hold-time mode
Daylight threshold
Sensitivity & More functions
Stand-by dimming level & Auto-cong.
This key is not appliable on this product.
This key is not appliable on this product.
This key is not appliable on this product.
7. Descriptions of the Button Functions (remote control HRC-11)
Press button “ON/OFF” to select permanent ON or permanent OFF mode.
* Press button “AUTO”/“RESET” to exit this mode.
For Sensor LED indicator references: Remains on 2s, initiate "Semi-auto" mode from "Auto" mode.
HRC-11
Press button “Shift”, the LED on the top left corner is on to indicate mode selection. All
values / settings in RED are valid for 20 seconds.
For example, to set detection range 100%, daylight threshold Disable, hold-time 5min,
stand-by time +∞, stand-by dimming level 30%, the steps should be:
Press button “Start”, button ”100%”, “Disable”, “Shift”, “5min”, “Shift”, “+∞”, “30%”,
“Memory”. By pointing to the sensor unit(s) and pressing “Apply”, all settings are passed
on the sensor(s).
Lux off
Exp 1
Exp 2
Press button “AUTO” to initiate automatic mode. The sensor starts working and all settings
remain as before the light is switched ON/OFF;
1. Press button “Shift” ,the red LED on.
2. Press button "SEMI-AUTO" to initiate Semi-auto mode. The sensor is only activated
with the manual press of push switch. To exit this mode, simply press button "AUTO".
1. Press button “Start” to program.
2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by
time”, “Stand-by dimming level” to set all parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s).
"Exp" refer to Expansion, these two buttons are reserved functions and pending future
development.
CCT+
CCT-
Sensor off Twilight
Shift
AUTO
100% 75% 50% 10%
2 Lux
100 Lux
10 Lux
300 Lux
50 Lux
500 Lux
Disable
Ambient
Memory Apply
Test
2 s
30 s
1 min 10 min
5 min 15 min 30 min
0s
10 s 1h
10% 20% 30% 50%
Dual tech & RF mode
SEMI-AUTO
Hold-time
Stand-by time
Stand-by dimming level & Auto-config.
Daylight threshold
Sensitivity & More functions
RX STBY%
PIR
RX 100%
HF HF+PIR HF/PIR
Shift Send
5 min 30 min
20 min
Power
100%
Power
80%
1 min 10 min +
Start
RESET
ON
OFF
24h 30s
12h 4h
Learn
Erase Transmit
Brightness
CCT-
CCT+
Tri-level Harvest Master ×
Exp 1 Exp 2 Lux off
This key is not appliable on this product.
This key is not appliable on this product.
This key is not appliable on this product.
Press buttons in zone “Power out” to select the light output at 80% (at initial 10,000 hours) or
100%.
Press these two buttons to adjust the light output brightness and set a new target lux level.
The daylight sensor can measure ambient daylight level and ignore the LED light, so as to
calculate how much articial light is needed to maintain the target lux level.
Press button “RESET”, perform DIP Switch/Rotary Switch settings.
*The default settings are: Detection range 100%; Hold-time 5min; Stand-by time +∞; Stand-by
dimming level 30%; Daylight threshold disable; HF/PIR detection mode.

8. Trouble Shooting
MALFUNCTION CAUSE REMEDY CAUSE REMEDY
The fixture does not light up
The fixture is always on
Check detection area setting
The fixture is on when it should not
Incorrect daylight threshold setting
Continous movement in the detection zone
Sudden change in temperature due to weather (wind, rain, snow) or air
expelled from fans, open windows
Detection zone not targeted
Faulty fixture
No power supply
Adjust daylight threshold setting
Replace fixture
Check power to sensor
Check detection area setting
Adjust zone, change installation site
HIM31-20230620-A1
9. Additional Information / Documents
1. Regarding precautions for microwave sensor installation and operation, please kindly refer to www.hytronik.com/download ->knowledge ->Microwave Sensors - Precautions for Product Installation and Operation
2. Regarding precautions for PIR sensor installation and operation, please kindly refer to www.hytronik.com/download ->knowledge ->PIR Sensors - Precautions for Product Installation and Operation
3. Regarding Hytronik standard guarantee policy, please refer to www.hytronik.com/download ->knowledge ->Hytronik Standard Guarantee Policy