Hytronik HMW23 User manual

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 1/5
IP20RED
Stand-by power
EMC standard (EMC)
Safety standard (LVD)
Certication
Radio Equipment (RED)
EN55015, EN61000
Semko, CB, CE, EMC, RED, RCM
EN60669, AS/NZS60669
Model No. HMW23
9.5 ~ 22.5VDC
Operating voltage
Input current
EN300440, EN301489,
EN62479
<0.5W
Input Characteristics
Safety and EMC
Approx. 12mA
Sensor Data
HMW23
Operation temperature Ta: -20
O
C~ +50
O
C
Environment
IP20
IP rating
Model No.
<0.2mW
5.8GHz +/- 75MHz
High Frequency (microwave)Sensor principle
Operation frequency
Transmission power
Detection range
Detection angle
Max. ( Ox H) 12m x 6m
20s
Warming-up
HMW23
Tri-level Control for System DALI
Stand-alone HF Motion Sensor
Technical Data
Ambient daylight
threshold
One-Key
Commissioning
Rotary Switch
Programing Rotary Switch Grouping
6
0
6
Detection Pattern
synchronization
control
TX
TX
TX
RX
360O
Infrared receiver
Photocell
LED indicator
DALI group selection
Lens
1
3
4
2
70mm 64.7
Ø85
65
56
16
9
(1) Sensor inset
(2) Lens pluggable
(3) Protection cover
(4) Ceiling (drill hole Ø70mm).
Rotary switch preset
HF
Mechanical Structure
Note:We recommend the mounting distance between sensor to sensor should be more than 2m to prevent sensors
from false-triggering.

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 2/5
Functions and Features
Tri-level Control (Corridor Function)
1
Hytronik builds this function inside the motion sensor to achieve tri-level control, for some areas which require a light change notice
before switch-off. The sensor offers 3 levels of light: 100%-->dimmed light -->off; and 2 periods of selectable waiting time: motion
hold-time and stand-by period; Selectable daylight threshold and freedom of detection area.
Synchronisation Function
2
By connecting the DALI terminals in parallel (see wiring diagram), no matter which sensor detects motion, all HMW23 in the group
will turn on the lights when surrounding natural light is below the daylight threshold. The detection area could be widely enlarged in
this way.
This DALI sensor is designed for incoporated in the DALI system, taking command from the DALI master, accepting and carrying out the
grouping work with up to 64 lumanaires. It can switch on/off, or dim the assigned group members and feed back the status to the
DALI master.
With sufcient natural light, the
light does not switch on when
presence is detected.
With insufcient natural light,
the sensor switches on the light
automatically when presence is
detected.
After hold-time, the light dims to
stand-by level.
Light switches off automatically
after the stand-by period
elapses.
DALI Grouping Selection
DALI group conguration can be done either on PC, or on the rotary coding switch:
a. There are 16 channels available on the rotary switch. “0” is for DALI broadcast, the rest 15 channels are for end-user to dene
the application unit.
b. PC grouping can overwrite rotary switch grouping, and vise versa. The last setting controls.
The rotary switch channels are corresponding to the groups listed below:
Switch channel DALI group Switch channel DALI group
0
1
2
3
4
5
6
7
broadcast
group 0
group 1
group 2
group 3
group 4
group 5
group 6
group 7
group 8
group 9
group 10
group 11
group 12
group 13
group 14
8
9
A
B
C
D
E
F
DALI group selection

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 3/5
0 5s100% Disable
1 1min100% 2Lux
2 5min100% 10Lux
3 5min100% 30Lux
4 5min100% 10Lux
5 5min100% 30Lux
6 5min100% Disable
7 10min100% 2Lux
8 10min100% 10Lux
9 10min100% 30Lux
A 10min100% Disable
B 10min75% 30Lux
C 10min50% 10Lux
D 30min100% 50Lux
E30min100% Disable
F5s100%
10%
10%
10%
10%
Disable
10%
30%
10%
10%
10%
30%
10%
10%
10%
30%
10%2Lux
10s
5min
10min
30min
0s
+∞
+∞
10min
30min
+∞
+∞
+∞
+∞
+∞
+∞
10s
Detection
range
Channel Hold-time Stand-by
time
Stand-by
dim level
Daylight
sensor
A rotary switch is built inside the sensor for scene
selection / fast programming. Total 16 channels
are available:
Rotary switch preset
Rotary Switch Preset
Note: settings can also be changed by remote control
HRC-11. The last action controls.
Press the buttons to select light output at 80% (at initial 10,000 hours) or 100%.
Note: “Sensor off” and “Twilight” functions are disabled.
Power output
Settings (Remote Control HRC-11)
Press button “RESET”, all settings go back to rotary switch settings.
Reset Settings
Permanent ON/OFF function
Press button “ON/OFF” to select permanent ON or permanent OFF mode.
* Press button “AUTO”, “RESET” to quit this mode.
The mode will change to AUTO Mode after power failure.
AUTO mode
Press button “AUTO” to initiate automatic mode. The sensor starts working and all
settings remain as before the light is switched ON/OFF.
Note: the function of Semi-auto is disabled.
ON/
OFF
&
A
4
4 hhh
HRC-11
Press button “Shift”, the LED on the top left corner is on to indicate mode selection.
All values / settings in RED are valid for 20 seconds.
Shift Button

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 4/5
Press the buttons to adjust the light brightness during hold-time.
Brightness +/-
Scene program - 1-key commissioning
Detection range
Press buttons in zone “Detection range” to set detection range at 100% / 75% / 50% / 10%.
Press buttons in zone “ Daylight threshold” to set daylight sensor at 2Lux/ 10Lux / 50Lux / 100Lux/ 300Lux/ 500Lux or Disable.
Daylight threshold
1. Press button “Shift”, the red LED starts to ash.
2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold.
Ambient daylight threshold
Hold-time
Press buttons in zone “hold-time” to set the hold-time at 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min.
Note: 1. To set hold-time at 30s / 5min / 15min / 30min, press “Shift” button rst.
2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.
*To exit from Test mode, press button “RESET” or any button in “Hold-time”.
1. Press button “Start” to program.
2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by time”, “Stand-by dimming level” to set all
parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s).
For example, to set detection range 100%, daylight threshold Disable, hold-time 5min, stand-by time +∞, stand-by dimming level 30%, the steps should be:
Press button “Start”, button ”100%”, “Disable”, “Shift”, “5min”, “Shift”, “+∞”, “30%”, “Memory”. By pointing to the sensor unit(s) and pressing “Apply”, all
settings are passed on the sensor(s).
Dual tech & RF mode
Stand-by dimming level
Stand-by time (corridor function)
Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞.
Note: “0s” means on/off control; “+∞” means bi-level control, the xture is 100% on when there is motion detected, and remains at the stand-by dimming level
when no presence after motion hold-time.
Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10% / 20% / 30% / 50%.
All buttons are disabled.
Auto-conguration function
All buttons in this zone are disabled.

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 5/5
L
N
Wiring Diagram
DALI power
supply DALI driver
Bus-mastering
DALI master
DALI driver DA1 DA2
HMW23
DA1 DA2
HMW23
Detection Pattern
Ceiling mounted height(m)
6
0
6
10%
30%
75%
50%
Additional Information / Documents
1. Regarding precautions for microwave sensor installation and operation, please kindly refer to
www.hytronik.com/download ->knowledge ->Microwave Sensors - Precautions for Product Installation and Operation
2. Regarding Hytronik standard guarantee policy, please refer to
www.hytronik.com/download ->knowledge ->Hytronik Standard Guarantee Policy