Hytronik HC419VRC/R User manual

INSTRUCTION MANUAL FOR MICROWAVE MOTION SENSOR
Model No.:HC419VRC/R
Technical Specifications
PRODUCT TYPE: Microwave Motion Sensor
OPERATING VOLTAGE: 120-277VAC 50Hz/60Hz
HF SYSTEM: 5.8GHz CW radar
RATED LOAD:120VAC / 3.4A / 400W
230VAC / 3.5A / 800W
277VAC / 3.7A / 1000W
DETECTION ANGLE: 30 ~150
POWER CONSUMPTION: <1W
DETECTION RANGE: Max.16 meters in diameter, adjustable
TIME SETTING: 5s~30min.
DAYLIGHT SENSOR: 2~50Lux; disable
STAND-BY PERIOD: 0s, 10s~1h, +
STAND-BY DIMMING LEVEL: 10%~30%
MOUNTING:Indoors,ceiling & wall mounted
INSTALLATION HEIGHT: ≤15M
WORKING TEMP.: -20 ~ +60℃
HC419VRC/R HRC-05
The sensor is an active motion detector; it emits a high-frequency electro-magnetic wave 5.8GHz and receives its echo. The sensor detects the change
in echo from movement in its detection zone. A microprocessor then triggers the switch light ON command. Detection is possible through doors, panels
of glasses thin walls.
Note: the high-frequency output of this sensor is <0.2mW; approximately just 0.2‰of the transmission power of a mobile telephone or the output of a
microwave oven.
IMPORTANT
PLEASE READ THESE INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION AND RETAIN THIS LEAFLET IN A KNOWN
AND SAFE PLACE FOR FUTURE REFERENCE.
SECTION 1 INSTALLATION AND WIRING
1.1 Ensure that the electricity supplyis switched off before installing or servicing thisproduct.
1.2 Wiring diagram
°°
(capacitive load) Sensor antenna
Buzzer LED indication
Detection area
Infrared remote receiver
Hold-time
Daylight threshold
Stand-by period
Stand-by dimming level
Daylight sensor
Installation hole
Push
L
N
L ’
SYNC
SYNC
1-10V
+
Stand-by dimming level
Detection range
ON/
OFFAuto ModeReset
Power
80%
Test
2s
10%20%
30s 1min
100%
30min10min5min
0s 10s1min
30%
SC1 SC2
SC3
Scene mode
10min
50%10%
30min
Hold-time
Stand-by period
5min
Lux
Disable
2Lux
10Lux
50Lux
Daylight Sensor
SC4
Power
100% +
-
Dim
M/A
8
Note: this 1-10V output is isolated, SELV output.Do not connect the
1-10V terminals on driver X to Driver Y.
Wiring diagram for synchronization function
LED Driver
LED1-10V
SYNCV01-1
LED Driver
LED1-10V
V01-1V01-1
LED1-10V LED Driver
Max.10pcs
SYNC SYNC
3rd Floor, block C, complex building, 155#, Bai'gang road south,
Bai'gang village, Xiao Jin Kou town, Huicheng district, Huizhou 516023
Tel:[phone] F:86-752-2777877
E: [email protected] W:www.hytronik.com
CHINA FACTORY
Room D, 10/f, Tower A, Billion Center, 1 wang Kwong Road,
Kowloon Bay, Kowloon, Hongkong
T: 00852-35197525 F: 00852-30116936
E: [email protected]
HYTRONIK INDUSTRIAL LIMITED

SECTION 2 REMOTE CONTROL
Permanent ON/OFF [ ]
1. Press button , the light goes to permanent ON or permanent OFF mode.
2. Press button to quit from this mode.
3. The mode will change to AUTO Mode after power failure.
(
Please refe
r
to explanation accordingly)
Auto Mode [ ]
Press button goes to auto mode, the sensor starts working and all settings remain the same as the latest status before the light was switched ON/OFF.
RESET [ ]
Press button , all settings go back tothe value of DIP settings.
Test 2s function [ ]
1. Press button , the sensor goes to test mode(hold time 2s), stand-by period and daylight sensor are disabled.
2. Press button to quit from this mode, and the sensor setting is changed accordingly.
Ambient daylight threshold [ ]
Press button , the latest surrounding lux value overwrites previous lux value learend, and is set as the daylight threshold.This feature enables the fixture
to function well in any real application circumstance.
Detection range[ ]
Press buttons in zoneto set detection range at 100% / 50% / 10%.
Hold time [ ]
Press buttons in zoneto set hold time at 30s / 1min / 5min / 10min / 30min.
Stand-by period [ ]
Press buttons in zoneto set stand-byperiod at 0s / 10s / 1min / 10min / 30min / +∞.
Note: “0s” means on/off control; “+∞” means bi-leve of dimming control, light never switches off.
Stand-by dimming level [ ]
Press buttons in zoneto set the stand-by dimming level at 10% / 20% / 30% .
Daylight sensor [ ]
Press buttons in zone to set daylight sensor at 2lux / 10lux / 50lux.
1
2
3
234
button 1
button 2
button 3
8
3
5
6
11
13
12
7
4
11
button 8
button
10
Power output [ ]
Press button , the output shifts between 80% (at initial 10,000 hours) and 100%, for energy saving purpose.
10
button 5
Dim +/- [ ]
Press button to adjust the light brightness during hold-time.”+” means dimming up, “-” means dimming down.
9
button 9
Lux disable [ ]
Press button , the built-in daylight sensor stops working, and all motion detected could turn on the lighting fixture, no matter how bright the natural light is.
14
button
14
Manual override/ absence detection [ ]
Press button , the sensor goes to manual override or absence detection function.
Note: The buzzer beeps twice if it’s manual override function, and beeps once if shifts to absence detection function.
button
15
15
zone6
zone
11
zone
12
zone
7
zone13
5
9
4
11
12
Stand-by dimming level
Detection range
ON/
OFFAuto ModeReset
Power
80%
Test
2s
10%20%
30s1min
100%
30min10min
5min
0s 10s 1min
30%
SC1 SC2
SC3
Scene mode
10min
50% 10%
30min
Hold-time
Stand-by period
5min
Lux
Disable
2Lux
10Lux
50Lux
Daylight Sensor
SC4
Power
100% +
-
Dim
M/A
3
1
2
7
8
6
10
13
14
15
HRC-05
Note: the buzzer beeps one time when RC
receives signal successfully

Scene mode options [ ]
Note:end-user can adjust the settings by pressing buttons of detection range / hold time / stand-by period / stand-by dimming level
/daylight sensor , the last setting stays in validity.
611
13
12
7
zone4
There are 4 scene modes built-in the remote control for different applications:
Scene options Detection range Hold time Stand-by period Stand-by dimming leveDaylight sensor
SC1 100% 1min 10min 10%2Lux
SC2 100% 5min 10min 10%2Lux
SC3 100% 10min 30min 10%10Lux
SC4 100% 10min + 10%50Lux
8
SECTION 3 SETTINGS
This is the time period you would like to keep at the low light output level before it is completely switched off in the long absence of people.
Stand-by period (corridor function)
This is the dimmed low light output level you would like to have after the hold-time in the absence of people.
Stand-by dimming level
The daylight threshold can be set on DIP switches, tofit for particular application.
Daylightsensor
Detection area can be reduced by selecting the combination on the DIP switches tofit precisely for each specific application.
Hold-time means the time period to keep the lamp on 100%, after all motion has ceased (detection area vacated).
Hold-time
Detection area
I – 100%
II – 50%
I – 0s
II – 10s
III – 1min
IV – 5min
V – 10min
VI – 30min
VII – 1h
VIII – +∞
I – Disable
II – 50Lux
III – 10Lux
IV – 2Lux
I– 10%
II – 30%
I – 5s
II – 3min
III – 10min
IV – 30min
1h
10min
30min
5min
1min
10s
8
76
+∞
0s
50%
100%
1
I
II
54
50Lux
10Lux
2Lux
Disable
I
II
III
IV
I
II
III
IV
V
VI
VII
VIII
30%
10%
1
I
II
32
3min
10min
30min
5s
I
II
III
IV
Note: “0s” means on/off control;
“+ ” means bi-level dimming control, fixture never switches off when daylight sensor is disabled.
8

SECTION 5 TROUBLE SHOOTING
SECTION 4 FUNCTIONS
YDEMERESUACYDEMERESUACNOITCNUFLAM
The load does not work
gnittestsujdAdetcelesgnitteslortnoc-thgiltcerrocnI
daolecalpeRytluafdaoL
NOhctiwSFFOhctiwssniaM
gnittesenozkcehCenoznoitcetedehtnitnemevomsuounitnoCnosyawlasidaolehT
The load is on without any identifiable
movement
The sensor is not mounted for reliably detecting movement Securely mountenclosure
Movement occurred, but not identified by the sensor
(movement behind wall, movement of small object in
immediate lamp vicinity etc.)
Check zone setting
The load does not work despite movement Rapid movements are being suppressed to minimize
malfunctioning or the detection radius is too small Check zone setting
4.1 Zero-cross Relay Operation
4.2 Synchronization Function
4.3 Manual Override
4.4 Absence Detection Function
4.5 Daylight Monitoring Function
Designed in the software, sensor switches on/off the load right at the zero-cross point, to ensure the in-rush current is minimised, enabling the
maximum lifetime of the relay.
Note: if the surrounding natural light of the sensor which detects movement is sufficient,all lights in the group will not be triggered on.
By connecting the “SYNC” terminals in parallel (maximum 10pcs, see wiring diagram), no matter which sensor detects motion, all HC419VRC/R in
the group will turn on the lights when surrounding natural light is below daylight threshold. The sensor antenna is shared and the detection area
could be widely enlarged in this way. Other settings such as hold-time, stand-by period, stand-by dimming level and daylight threshold on each
individual unit stay the same.
Motion sensor is employed, but only activated on the maunal press of the push switch, light keeps on in the presence, and dimmed down in the
absence, and eventually switch off in the long absence.
Hytronik specially design this function in software for deep energy-saving purpose. A built-in daylight sensor is designed to provide “smart photocell”
function. This function can only be activated when stand-by period is set to “+∞ ”.
This sensor reserves the access of manual override function for end-user to switch on/off, or adjust the brightness by push-switch, which makes
the product more user-friendly and offers more options to fit for some extra-ordinary demands:
* Short push (<1s): on/off function;
On → off: the light turns off immediately and can not be lighten for a certain time (equals to hold-time preset) even movement is detected.
After this period, the sensor goes to sensor mode.
Off →on: the light turns on and goes to sensor mode, no matter if ambient Lux level exceeds the daylight threshold or not.
* Long push (>1s): dim up/down the hold-time brightness between 10% and 100%. Both the settings on DIP switch and manual override can
overwrite each other, the latest action controls.
Note: if end-user do not want this manual override function, just leave the “push” terminal alone and don’t connect it to any wire.