I-care HOME2 User manual

Quick Guide
iCare HOME2
Quick Guide iCare HOME2
EN Quick Guide
FI Pikaohje
SV Snabbhandledning
DA Lynvejledning
NO Hurtigveiledning
EL Γρήγορος Οδηγός
CS Stručný návod

If you need help in using the iCare HOME2
tonometer, contact your healthcare
professional.
For safety information, read Chapter 1 in
the Instruction Manual before using the
tonometer.
PRECAUTION! Before taking measurements,
update the tonometer’s time to your
local time manually from the tonometer’s
settings or automatically by connecting
the tonometer to the iCare PATIENT2
application or to the iCare EXPORT
software.
Read this Quick Guide and watch
the HOME2 user instructions video
before using the tonometer. Follow
the instructions step by step.

1 Inserting the batteries 5
2 Inserting the probe 6
3 Switching on 7
4 Correct measurement position 8
5 Adjusting the supports and positioning the tonometer 9
6 Measuring eye pressure 11
7 Measuring eye pressure in the supine position 13
8 Troubleshooting 15
9 Switching off the tonometer and disposing of the probe 17
Step Page
ENGLISH

4
1Probe
2Probe base
3Cheek support
4Forehead support
5Measure button
6Select button
7Display
8Battery cover
9Wrist strap
10 Probe applicator
11 Screwdriver Torx TX8
Tonometer parts
5
7
9
4 3
12
10
11
8
6

54 Inserting the batteries
1
Open the battery
cover with the
screwdriver.
Insert the batteries, and close
the cover.
The batteries are in the tonometer carrying
case under the box of probes.
AA/LR6
AA/LR6
AA/LR6
AA/LR6

6
Inserting the probe
2
Place the probe
applicator over the
probe base.
Open the
packaging.
Remove the cap.
WARNING! To prevent contamination, keep unused probes in
their box. Do not touch a bare probe. Do not use a probe if it
touches a non-sterile surface such as a table or a floor.
Do not use a
probe if it has
touched your
hand, a table, or
other nonsterile
surface.

76
Drop the probe
from the
container to the
probe applicator.
Remove the probe applicator.

8
3Switching on
Press down
until you hear a
beep. The text
“Start” is shown
on the display.
Alternatively, press down until you
hear a beep. Then press again to
enter the measurement mode. The text
“Start” is shown on the display.
3s
3s
OR

98 Correct measurement position
4
Positioning the tonometer is instructed in the
following section.
Look straight ahead and the
tonometer is at a 90-degree
angle to your face. The probe is
about 5 mm from your eye and
points perpendicularly to the
center of your eye.
The forehead
support A rests
on your forehead
and the cheek
support B rests
on your cheek.
If you see a red light in the probe
base, the tonometer is tilted too
much downwards. You should
straighten your posture and lift
your chin.
START
<90°
START 90°

10
5Adjusting the supports and positioning the tonometer
START
WARNING! Only the probe should touch the eye. Do not touch your eye with any
other parts of the tonometer. Do not poke your eye with the tonometer.
Place the tonometer against your face and
look into the probe base. The probe points
perpendicularly to the center of your eye
when the blue and green rings in the probe
base are symmetrical.
Before the measurement,
adjust the forehead and
cheek supports to the
correct length. Start
with the supports at the
maximum length.
Shorten the supports
only two clicks at a
time to prevent the
tonometer from getting
too close to your eye.

1110
START
START
5 mm
Keep both eyes
open. Covering
the eye not being
tested may help
you see the rings
more clearly.
Shorten the supports by rotating them
clockwise two clicks at a time until you only
see a symmetrical green ring. The tonometer is
now at the correct distance from your eye.
If the rings are not symmetrical,
the probe does not point
perpendicularly to the center of
your eye. Correct the position of
the tonometer.

12
6Measuring eye pressure
Start the measurement
when you see only a
symmetrical green ring.
Press the Measure button
once. The probe gently
touches your eye.
If the probe base ashes
red and you hear multiple
beeps, the measurement
was not successful. See
Troubleshooting on page 17.
A single beep indicates a
successful measurement.
Continue taking measu-
rements until you hear a
long beep and the light in
the probe base turns off.
1x
START

1312
6x
A measurement sequence consists of
six measurements.
Tip: You can also take the measurement
sequence by pressing and holding the
Measure button down until all six
measurements have been taken.
When all six measure-
ments have been success-
fully taken, you hear a
longer beep, the light in
the probe base turns off,
and you see the result on
the display.
Press the Measure button
once and repeat the
measurement on your
other eye.
START

14
7Measuring eye pressure in the supine position
Before measuring, lie down
for a moment.
Avoid bending your head
backwards.
Take a comfortable position
on your back with a pillow
behind your neck. Look
straight ahead.

1514
Place the tono-
meter at a 90
degrees angle on
your face and take
the measurement
as previously
instructed.
After a successful
measurement, press
the Measure button
once and repeat the
measurement on your
other eye.
START

16
8Troubleshooting
If an error occurs, the probe base ashes red. The
display and sounds indicate the source of the error.
Look at the display, press the Measure button
once, make the necessary corrections, and repeat
the measurement.

1716
va u
Icon Display text Sound Problem Solution
TOO FAR 3 long The probe is too far away from the
eye. Press the Measure button once to acknowledge the error.
Shorten the forehead and cheek supports.
TOO NEAR 5 short The probe is too close to the eye. Press the Measure button once to acknowledge the error.
Lengthen the forehead and cheek supports.
INCORRECT
ALIGNMENT
2 short The probe was not perpendicular to
the cornea or the probe hit an
eyelid or eyelashes.
Press the Measure button once to acknowledge the error.
Position the tonometer so that the probe points perpendicu-
larly to the center of your eye. Keep your eye properly open.
REPEAT 2 short There was a problem with the
movement of the probe. Press the Measure button once to acknowledge the error.
Repeat the measurement.
DETECTION
ERROR
2 short The sensor could not identify the
measured eye (right or left).
Press , then press until the correct eye (right or left) is
shown on the display. Press , or press the return button to
cancel the measurement.

18
9Switching o the tonometer and disposing of the probe
Dispose of the probe
and the container in
a mixed waste bin.
Press and hold
the Select button
until you hear
3 beeps and the
display switches o.
Remove the probe
and place it back
into the probe
container.
3s

1918
Now you can transfer your measurement
results to your doctor’s iCare CLINIC or to
your private account in the iCare CLOUD by
using the iCare PATIENT2 app on your mobile
device or the iCare EXPORT software on your
computer.
START

Jos tarvitset apua iCare HOME2
-silmänpainemittarin käyttämisessä, ota
yhteyttä terveydenhuollon ammattilaiseen.
Lue käyttöohjeen luvussa 1
olevat turvallisuustiedot ennen
silmänpainemittarin käyttöä.
HUOMAUTUS! Päivitä silmänpainemittarin
aika-asetukset ennen mittauksia paikal-
liseen aikaan manuaalisesti silmänpaine-
mittarin asetuksista tai automaattisesti
yhdistämällä silmänpainemittari
iCarePATIENT2-sovellukseen tai i
CareEXPORT-ohjelmistoon.
Lue tämä pikaohje ja katso
HOME2-käyttöohjevideo ennen
silmänpainemittarin käyttöä.
Noudata ohjeita vaihe vaiheelta.