I-care IC333 User manual

IC333 BED SYSTEM
OPERATING MANUAL &
WARRANTY
NEED HELP? CALL OUR TEAM
AU: 1800 105 853 | NZ: 0800 143 922

1. SPECIAL NOTES
2. GENERAL GUIDELINES
3. UNPACKING
4. ASSEMBLY
5. OPERATION
6. HEADBOARD INSTALLATION
7. WARRANTY TERMS

SIGNAL WORD MEANING
DANGER
Danger indicates an imminently hazardous
situation which if not avoided, will result in
death or serious injury.
WARNING
Warning indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
CAUTION
Caution indicates a potentially hazardous
situation which, if not avoided, may result in
property damage
NOTICE
The information contained in this document is subject to change without notice
SPECIAL NOTES:
Signal words are used in this manual and apply to hazards or unsafe practices which
could result in personal injury or property damage. Refer to the table below for defini-
tions of the signal words.
This model meets Australian and New Zealand Standards and is registered by the Thera-
peutic Goods Administration.

GENERAL GUIDELINES:
OPERATING INFORMATION
 DO NOT use near explosive gases
 Keep the product a minimum of 30cm away from any direct heat source
 Close supervision is necessary when this product is used by or near children
 Check all parts for shipping damage and test before using. In case of damage, DO
NOT use. Contact a qualified technician for further instructions
 After any adjustments, repair or service and before use, make sure all attaching hard-
ware is tightened securely.
 DO NOT let any individual underneath the bed or in between the raised bed frame
components at anytime.
 When the bed is not to be used for an extended period of time, unplug the electric
bed from the wall outlets.
 If a liquid is spilled in or around the electric bed, unplug the electric bed before clean-
ing, clean up the spill and allow the electric bed or the area around the electric beds
to dry thoroughly before using the electric controls again.
 Body weight should be evenly distributed over the surface of the bed. DO NOT lie, sit
or lean in such a way that your entire body weight is placed only on raised head or
foot sections of the bed.
 When operating/moving manual electric beds, always ensure that the individual utilis-
ing the bed is positioned properly within the confines of the bed. DO NOT let any ex-
tremities protrude over the side or between the bed rails when performing these func-
tions.
 After the manual/electric bed has been assembled, always test to make sure that all
sections of the manual/electric bed are properly and securely in place before using.
 If the unit is not working properly, call a qualified technician to examine the unit and
repair it.
 Keep all moving parts, including the main frame, mattress deck (head and foot
springs/sections) and all drive shafts, free of obstruction (i.e. blankets/sheets, heating
blankets/pads, tubing, wiring, etc. and other types of products using electric cords
which may get tangled around the bed, side rails or legs) during operation of manual/
electric bed.
 The manual/electric bed is equipped with locking castors. When transferring into or out
of the manual/electric bed, always lock the locking castor(s). Inspect the wheel locks
for correct locking action before actual use. Even with castors properly locked, some
flooring surfaces such as tile or wood, will allow the bed to move under some condi-
tions. To use on surfaces such as these must be evaluated by the care provider.

UNPACKING:
RECEIVING
1. Count cartons before signing shipping papers
2. Designate someone at the facility to receive and inspect all merchandise. Use the
master order acknowledgement to check off items as they are received.
3. Compare the number of cartons shipped with the number of cartons actually re-
ceived and note such on the consignee copy of the freight bill. Make sure to have
the truck driver sign the copy acknowledging the account.
4. If a shortage occurs, IMMEDIATLEY contact Sleep Systems Customer Service depart-
ment.
UNPACKING
NOTE: Check all the parts for shipping damage. In case of shipping damage, DO NOT
use. Contact Sleep Systems for further instructions.
TIP! ROLL BED OUT OF BOX ON THE FLAT & THEN STAND ON
ITS SIDE AS SEEN BELOW.
Remote control
Control Box
Power Cord & package of
Headboard Bolts
Electric Actuators
Retainer Bar

ASSEMBLY:
1: Remove power cord, hand piece and retainer bar from underneath the bed
2: Insert retainer bar into the holes at the end of bed
3: Move bed into desired position, plug into power. Then raise the bed and
lock all the castors

OPERATION:
IC333 ELECTRIC BED OPERATION
WARNING!
NEVER operate if the unit has a damaged cord or plug. If it is not working properly, call a
qualified technician for examination and repair.
Keep all electrical cords away from heated or hot surfaces.
Ensure all cables and cords are routed such that they will not become entangled or
pinched. Otherwise damage or injury may result.
CAUTION!
Allow a slight pause between adjustments and avoid pressing multiple buttons at the
same time. If pendant buttons are depressed too rapidly or multiple buttons are pressed
at the same time, the desired feature may not activate. Simply release the pendant but-
ton, permit a slight pause and then activate the next operation.
1. Before placing the bed into use, test it by operating it through all phases of its oper-
ation.
2. If any problems arise during the test, recheck all electrical and mechanical connec-
tions.
3. IC333 electrical beds use a ten function hand piece for all bed operations
REMOTE CONTROL
Head & Knee Lower
Knee Lower
Height Lower
Head lower
Reverse
Trendelenburg
Head & Knee Raise
Knee Raise
Height Raise
Head Raise
Trendelenburg

HEABOARD INSTALLATION:
STEP ONE: Unpack headboard
STEP 2: Place headboard in position (this may require two people)
STEP 3: Screw headboard bolts into the holes provided. Tip: screw
in the top ones for a start.

LIMITED WARRANTY TERMS & CONDITIONS:
Sleep Systems warrants the IC333 Height Adjustable Bed and parts to the Customer against
defective materials and defective workmanship, from date of invoice.
Steel Frame of Bed - 10 Year Limited Warranty
Actuators - 5 Year Limited Warranty
Hand Piece - 2 Year Limited Warranty
Control Box - 5 Year Limited Warranty
Upholstered Surround and Fabric - 3 Year Limited Warranty
Castor wheels - 5 Year Limited Warranty
Any warranty does not apply in circumstances where:
a. The goods or services are not defective;
b. The goods were used or services required for a purpose other than which they are intended;
c. The goods were repaired, modified or altered by any person other than Sleep Systems;
d. The defect has arisen due to misuse, neglect or accident;
e. The defect has arisen due to the incorrect installation of the goods;
f. The goods have not been stored or maintained as recommended by Sleep Systems or agents;
g. The defect has arisen due to normal; wear and tear on the goods; or
h. The Customer is in breach of the conditions.
In order to make claim under this warranty, a person must:
a. Provide written details/pictures of any defect in the products together with documentary proof
of the date of purchase of the product within 30 days of identifying the defect;
b. Allow Sleep Systems or its employees or agents to inspect the products;
c. Provide any information requested by Sleep Systems in relation to the products or installation of
the products.
Where Sleep Systems supplied goods via a third party, the third party’s warranty is the only
warranty provided to the Customer.
Sleep Systems will use its best endeavours to meet any estimated dates but will in no circumstances
whatsoever be liable for any loss or damage suffered by the customer or third party for failure to
meet any estimated date.
The warranty is personal to the purchaser and is not able to transferred or assigned.

CONDITIONS
This warranty covers products where Sleep Systems has established there has been a manufactur-
ing or material defect within the warranty period. Sleep Systems will at its discretion either repair or
replace the faulty products. The original warranty expiry date will still apply to the repaired or re-
placed products. All warranty issues and returns are to be directed to the Original Equipment Man-
ufacturer or Supplier of the original equipment the Sleep Systems products has been used in. Sleep
Systems obligation is to the original Equipment Manufacturer that has purchased the products and
incorporated them into the finished equipment. Fair wear and tear is not covered by warranty.
Warranty will be void where the products have been altered, varied, modified, adjusted, repaired
or attended to in any way without Sleep Systems written consent or in the event that the products
have been damaged, abused or used improperly or negligently in any way. This statement does
not confer, extend or vary any rights to parties or alter or extend any warranties offered by the
Original Equipment Manufacturer. Sleep Systems has sold the products to the Original Equipment
Manufacturer subject to our terms and conditions of sale.
LIABILITY
Except as specifically set out in these conditions, or contained in any warranty statement provided
with the goods or services, any term condition or warranty in respect of the quality, merchantabil-
ity, fitness for purpose, condition, description, assembly, manufacture, design or performance of
the goods or services, whether implied by stature, common law, trade usage, custom or otherwise,
is expressly excluded.
Replacement or repair of the goods or retroversion of the services is the absolute limit of Sleep Sys-
tem Liability arising under or in connection with the description, quality, condition, performance,
assembly, manufacturer, design, merchantability or fitness for purpose of the goods or services or
alternatively the sale, use of, storage or any other dealings with the goods or service by the cus-
tomer or any third party.
Sleep Systems is not liable for any indirect or consequential losses or expenses suffered by the Cus-
tomer or any third party, howsoever caused, including but not limited to loss of turnover, profits,
business or goodwill or any liability to any other party.
Sleep Systems will not be liable for any loss or damage suffered by the Customer where Sleep Sys-
tems has failed to meet any delivery date or cancel or suspends the supply of goods or services.
Nothing in these conditions is to be interpreted as excluding, restricting or modifying or having the
effect of excluding, restricting or modifying the application of any state or federal legislation appli-
cable to the sale of goods or the provision of services which cannot be excluded, restricted or
modified.
The Customer indemnifies Sleep Systems against all liabilities and cost (including) all legal costs on
an indemnity basis, expense, losses, damages or claims in any way as a result of the Customer fail-
ure to comply with any part of these conditions.