IBASE Technology IP413 Series User manual

IP413
ATX COM Express Type 6 Baseboard
User’s Manual
Version 1.0
(July 2017)

ii
IP413 User’s Manual
Copyright
©2017 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval system,
translated into any language or transmitted in any form or by any means,
electronic, mechanical, photocopying, or otherwise, without the prior written
consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the products
described in this document without prior notice. Every effort has been made to
ensure the information in the document is correct; however, IBASE does not
guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising from
misapplication or inability to use the product or the information contained herein,
nor for any infringements of rights of third parties, which may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for
identification purposes only and may be trademarks and/or registered trademarks
of their respective owners.

IP413 User’s Manual
iii
Compliance
In a domestic environment, this product may cause radio interference in which
case users may be required to take adequate measures.
This product has been tested and found to comply with the limits for a Class A
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with manufacturer’s instructions, may cause
harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household
waste, in accordance with the EU directive of for waste
electrical and electronic equipment (WEEE - 2012/19/EU).
Instead, it should be disposed of by returning it to a
municipal recycling collection point. Check local
regulations for disposal of electronic products.
Green IBASE
This product is compliant with the current RoHS
restrictions and prohibits use of the following substances
in concentrations exceeding 0.1% by weight (1000 ppm)
except for cadmium, limited to 0.01% by weight (100 ppm).
•Lead (Pb)
•Mercury (Hg)
•Cadmium (Cd)
•Hexavalent chromium (Cr6+)
•Polybrominated biphenyls (PBB)
•Polybrominated diphenyl ether (PBDE)

iv
IP413 User’s Manual
Important Safety Information
Carefully read the precautions before using the board.
Environmental conditions:
•Use this product in environments with ambient temperatures between 0˚C
and 60˚C.
•Do not leave this product in an environment where the storage temperature
may be below -20°C or above 80°C. To prevent from damages, the product
must be used in a controlled environment.
Care for your IBASE products:
•Before cleaning the PCB, unplug all cables and remove the battery.
•Clean the PCB with a circuit board cleaner or degreaser, or use cotton swabs
and alcohol.
•Vacuum the dust with a computer vacuum cleaner to prevent the fan from
being clogged.
WARNING.
Attention during use:
•Do not use this product near water.
•Do not spill water or any other liquids on this product.
•Do not place heavy objects on the top of this product.
Anti-static precautions
•Wear an anti-static wrist strap to avoid electrostatic discharge.
•Place the PCB on an anti-static kit or mat.
•Hold the edges of PCB when handling.
•Touch the edges of non-metallic components of the product instead of the
surface of the PCB.
•Ground yourself by touching a grounded conductor or a grounded bit of metal
frequently to discharge any static.
CAUTION
Danger of explosion if the internal lithium-ion battery is replaced by an incorrect
type. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s
instructions or recycle them at a local recycling facility or battery collection point.

IP413 User’s Manual
v
Warranty Policy
•IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of shipment
cannot be ascertained, the product serial numbers can be used to determine
the approximate shipping date.
•3rd-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are not
manufactured by IBASE, such as CPU, CPU cooler, memory, storage
devices, power adapter, panel and touchscreen.
＊PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE
TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED
FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest information
about the product.
2. If you need any further assistance from your distributor or sales
representative, prepare the following information of your product and
elaborate upon the problem.
•Product model name
•Product serial number
•Detailed description of the problem
•The error messages in text or in screenshots if there is any
•The arrangement of the peripherals
•Software in use (such as OS and application software, including the
version numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and
contact your distributor or sales representative.

vi
IP413 User’s Manual
Table of Contents
Compliance.....................................................................................iii
Important Safety Information........................................................iv
Warranty Policy ...............................................................................v
Technical Support & Services .......................................................v
Chapter 1 General Information.............................................1
1.1 Introduction .........................................................................................2
1.2 Features..............................................................................................2
1.3 Specifications......................................................................................3
1.4 Overview.............................................................................................5
1.5 Dimensions .........................................................................................7
Chapter 2 HardwareConfiguration..........................................8
2.1 Setting the Jumpers ............................................................................9
2.2.1 How to Set Jumpers...............................................................9
2.2 Connector Locations on IP413 ..........................................................10
2.3 Jumpers Quick Reference.................................................................11
2.3.1 AT/ATX Power Selection (J9)..............................................11
2.3.2 LVDS Panel Power (JP10)..................................................12
2.3.3 LVDS Backlight Power Selection (JP8) ...............................13
2.3.4 COM1 RS-232/422/485 Selection (JP2, JP3, JP4)..............14
2.3.5 PS/2 KB/MS Power Selection (JP12)..................................15
2.3.6 COM1 & COM2 RS-232 Power Selection (JP6, JP5)..........16
2.4 Connectors Quick Reference.............................................................17
2.4.1 SATA HDD Power Connector (J10).....................................18
2.4.2 PS/2 Keyboard and Mouse Connector (J6) .........................19
2.4.3 COM1 & COM2 RS-232/422/485 Ports (CN3).....................20
2.4.4 Audio Connector for Chassis Front Panel (JP1)..................21
2.4.5 BIOS Boot Selection (SW1) ................................................22
2.4.6 COM3 & COM4 RS-232 Port (J2, J1)..................................23
2.4.7 ATX Power Supply Connector (J12)....................................24
2.4.8 DC-In 12V Power Connector (J11)......................................25
2.4.9 Panel Inverter Power Connector (JP7) ................................25
2.4.10 LVDS Connector (CN9, CN8)..............................................26

IP413 User’s Manual
vii
2.4.11 USB 2.0 Ports (JP9)............................................................27
2.4.12 System Function Connector (J8).........................................28
2.4.13 Parallel Port (LPT1).............................................................29
2.4.14 Fan Power Connector (CPU_FAN, SYS_FAN)....................30
2.4.15 DVI Port (JP13)...................................................................31
2.4.16 VGA Port (VGA1)................................................................32

viii
IP413 User’s Manual
This page is intentionally left blank.

1
Chapter 1
General Information
The information provided in this chapter includes:
•Features
•Specifications
•Board Overview
•Board Dimensions

2
IP413 User’s Manual
1.1 Introduction
IP413 is a ATX COM Express Type 6 baseboard, offering expansion slots like ISA
and PCI and rich peripheral ports as the photo shown below. It is able to be
operated at the ambient operating temperature ranging from 0 ~ 60 °C and even
from -20 ~ 80 °C for storage.
Photo of IP413-ATX
1.2 Features
•1x PCI-E(x16), 1x PCI-E(x4), 3x PCI-E(x1) expansion slots
•Rich peripheral ports: USB 3.0, USB 2.0, LAN, DP, HDMI, audio jacks, serial
COM port
•On-board headers for serial port (from COMe module), PS/2 KB & MS,
DVI-D, CRT, and ATX power connector, and COM Express (Type 6)
connectors
•ATX power connector / DC-In 12V

General Information
IP413 User’s Manual
3
1
1.3 Specifications
Product Name
IP413
Form Factor
ATX COM Express Type 6 baseboard
Power Supply
ATX Power
Dimensions
305 x 244 mm (12” x 9.61”)
RoHS
Yes
I/O Ports / Connectors
Power Supply
•ATX Power
•DC-In 12V
Display
•1 x HDMI
•1 x DisplayPort
•1 x DVI-D
•1 x VGA
•1 x LVDS
LAN
1 x RJ45 10/100 Mbps LAN
USB
•4 xUSB 2.0 (2 are on the I/O coastline, and 2 are
on-board box-headers.)
•4 x USB 3.0
Serial
2 x COM ports:
•COM1: RS-232/422/485
(I/O coastline connector)
•COM2: RS-232 (full-function)
(I/O coastline connector)
•COM3 & COM4: RS-232 (TX and RX)
(from COMe module, via an on-board
box-header)
Audio Jacks
•1 x Line-In
•1 x Line-Out
•1 x Microphone Input

4
IP413 User’s Manual
Keyboard &
Mouse
1 x PS/2 keyboard / mouse on-board header
Battery for
RTC/CMOS
1 x Lithium battery cell for RTC of COM Express
module
Expansion
Slots
•1 x PCIe (x16) slot
•1 x PCIe (x4) slot
•3 x PCIe (x1) slot
•1 x Full-sized mini-PCIe (x1) slot with PCIe only
(half-sized mounting hole is reserved.)
Environment
Temperature
•Operation: 0 ~ 60 °C
•Storage: -20 ~ 80 °C
Relative
Humidity
10 ~ 90 %
All specifications are subject to change without prior notice.

General Information
IP413 User’s Manual
5
1
1.4 Overview
Top View
IP413-ATX
IP413-DC
＊The photos above are for reference only. Some minor components may differ.

6
IP413 User’s Manual
I/O View
No.
Name
No.
Name
1
COM1 RS-232/422/485 Port
6
DisplayPort
2
COM2 RS-232 Port
7
USB 3.0 Ports
3
GbE LAN Port
8
Audio Line-In
4
USB 2.0 Ports
9
Audio Line-Out
5
HDMI Port
10
Microphone Input

General Information
IP413 User’s Manual
7
1
1.5 Dimensions
243.84
237.49
165.1
33.02
10.16
28.38
0
35.52
31.05
6.35 16.6 48.62 70.62 92.36 111.96 128.99 146.12 163.83 288.29 304.8
0
0

8
Chapter 2
Hardware Configuration
This section provides information on jumper settings and connectors
on the IP413 in order to set up a workable system.
•Jumper and connector locations
•Jumper settings and information of connectors

Hardware Configuration
IP413 User’s Manual
9
2
2.1 Setting the Jumpers
Set up and configure your IP413 by using jumpers for various settings and
features according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your use.
2.2.1 How to Set Jumpers
Jumpers are short-length conductors consisting of several metal pins with a
non-conductive base mounted on the circuit board. Jumper caps are used to have
the functions and features enabled or disabled. If a jumper has 3 pins, you can
connect either PIN1 to PIN2 or PIN2 to PIN3 by shorting.
Pin# 1 23
A 3-pin jumper
A jumper cap
Refer to the illustration below to set jumpers.
Pin closed
Oblique view
Schematic illustration in the manual
Open
1 2 3
1-2
1 2 3
2-3
1 2 3
When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e.
turned On.
When a jumper cap is removed from two jumper pins, this jumper is open, i.e.
turned Off.

10
IP413 User’s Manual
2.2 Connector Locations on IP413
PCIEX1-3 PCIEX4-1 PCIEX16 PCIEX1-2 PCIEX1-1
Battery
JP9
JP7
VGA1
JP8
JP10 J2
J1
J3
SYS_FAN1
J10
JP1
1
1
9
2
10
1
210
CN10
CN11
CN8
RESC2 RESC1
CN9
CN12 CN13
1
1
2
1
3
4J11 J12
J7
1
1
15
1
16
5
9
16
5
9
1
9
2
10
12
1920
JP12
SW1
SW2 SW3
J5 J4
J6
LPT1
JP11
CPU_FAN1
JP2
JP4
JP6
JP5
JP3
CN3
CN7CN1CN2CN5CN4
CN6
J8
J9
JP13
1
11
1
11
1
11
1
13
1
1
1
7
7
1 2
19 20
1
1
13
Board diagram of IP413

Hardware Configuration
IP413 User’s Manual
11
2
2.3 Jumpers Quick Reference
Function
Jumper Name
Page
AT/ATX Power Selection
J9
11
LVDS Panel Power
JP10
12
LVDS Backlight Power Selection
JP8
13
COM1 RS-232/422/485 Selection
JP2, JP3, JP4
14
PS/2 Keyboard & Mouse Power
Selection
JP12
15
COM1 & COM2 RS-232 Power
Selection
JP6 (for COM1),
JP5 (for COM2)
16
2.3.1 AT/ATX Power Selection (J9)
1
Function
Pin closed
Illustration
ATX
(default)
Open
1
AT
Close
1

12
IP413 User’s Manual
2.3.2 LVDS Panel Power (JP10)
1
Function
Pin closed
Illustration
3.3V
(default)
1-2
1
5V
2-3
1