IBASE Technology IB995 User manual

IB995
Intel®8th or 9th Gen. Xeon. Core™ i7/i5/i3
Full-Size CPU Card
User’s Manual
Version 1.0
(Oct. 2019)

ii
IB995 User’s Manual
Copyright
©2019 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval
system, translated into any language or transmitted in any form or by any
means, electronic, mechanical, photocopying, or otherwise, without the prior
written consent of IBASE Technology, Inc. (hereinafter referred to as
“IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the
products described in this document without prior notice. Every effort has
been made to ensure the information in the document is correct; however,
IBASE does not guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising
from misapplication or inability to use the product or the information
contained herein, nor for any infringements of rights of third parties, which
may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for
identification purposes only and may be trademarks and/or registered
trademarks of their respective owners.

IB995 User’s Manual
iii
Compliance
In a domestic environment, this product may cause radio interference in
which case users may be required to take adequate measures.
This product has been tested and found to comply with the limits for a Class
A device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with manufacturer’s
instructions, may cause harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household
waste, in accordance with the EU directive of for waste
electrical and electronic equipment (WEEE - 2012/19/EU).
Instead, it should be disposed of by returning it to a
municipal recycling collection point. Check local
regulations for disposal of electronic products.
Green IBASE
This product is compliant with the current RoHS
restrictions and prohibits use of the following substances in
concentrations exceeding 0.1% by weight (1000 ppm)
except for cadmium, limited to 0.01% by weight (100 ppm).
•Lead (Pb)
•Mercury (Hg)
•Cadmium (Cd)
•Hexavalent chromium (Cr6+)
•Polybrominated biphenyls (PBB)
•Polybrominated diphenyl ether (PBDE)

iv
IB995 User’s Manual
Important Safety Information
Carefully read the precautions before using the board.
Environmental conditions:
•Use this product in environments with ambient temperatures between
0˚C and 60˚C.
•Do not leave this product in an environment where the storage
temperature may be below -20°C (-4°F) or above 80°C (176°F). To
prevent from damages, the product must be used in a controlled
environment.
WARNING.
Attention during use:
•Do not use this product near water.
•Do not spill water or any other liquids on this product.
•Do not place heavy objects on the top of this product.
Anti-static precautions
•Wear an anti-static wrist strap to avoid electrostatic discharge.
•Place the PCB on an anti-static kit or mat.
•Hold the edges of PCB when handling.
•Touch the edges of non-metallic components of the product instead of
the surface of the PCB.
•Ground yourself by touching a grounded conductor or a grounded bit of
metal frequently to discharge any static.
CAUTION
Danger of explosion if the internal lithium-ion battery is replaced by an
incorrect type. Replace only with the same or equivalent type recommended
by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions or recycle them at a local recycling facility or
battery collection point.

IB995 User’s Manual
v
Warranty Policy
•IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of
shipment cannot be ascertained, the product serial numbers can be
used to determine the approximate shipping date.
•3rd-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are
not manufactured by IBASE, such as CPU, CPU cooler, memory,
storage devices, power adapter, panel and touchscreen.
＊PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL
BE TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL
BE BILLED FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest
information about the product.
2. If you need any further assistance from your distributor or sales
representative, prepare the following information of your product and
elaborate upon the problem.
•Product model name
•Product serial number
•Detailed description of the problem
•The error messages in text or in screenshots if there is any
•The arrangement of the peripherals
•Software in use (such as OS and application software, including the
version numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the
form and contact your distributor or sales representative.

vi
IB995 User’s Manual
Table of Contents
Compliance..................................................................................... iii
Important Safety Information........................................................ iv
Warranty Policy............................................................................... v
Technical Support & Services....................................................... v
Chapter 1 General Information............................................. 1
1.1 Introduction......................................................................................... 2
1.2 Features ............................................................................................. 2
1.3 Packing List ........................................................................................ 3
1.4 Optional Accessories .......................................................................... 3
1.5 Specifications...................................................................................... 4
1.6 Block Diagram..................................................................................... 6
1.7 Board Pictures .................................................................................... 7
1.8 Dimensions......................................................................................... 8
Chapter 2 Hardware Configuration.......................................... 9
2.1 Essential Installations Before You Begin........................................... 10
2.1.1 Installing the CPU................................................................ 10
2.1.2 Installing the Memory........................................................... 11
2.2 Setting the Jumpers.......................................................................... 12
2.3 Jumper & Connector Locations on IB995.......................................... 13
2.4 Jumpers Quick Reference................................................................. 14
2.4.1 PCIe (x16) Bifurcation Selection (JP2 & JP3)...................... 15
2.4.2 LVDS Power Brightness Selection (JP4)............................. 16
2.4.3 LVDS Panel Power Selection (JP6) .................................... 16
2.4.4 Clearing ME Register (JP8) ................................................ 17
2.4.5 Clearing CMOS Data (JP9)................................................. 17

IB995 User’s Manual
vii
2.5 Connectors Quick Reference.............................................................18
2.5.1 COM1 RS-232/422/485 & COM2 RS-232 Serial Port (J25)..19
2.5.2 COM2~COM4 RS-232 Ports (J26, J5, J6) ...........................20
2.5.3 Digital I/O Connector (J2) ....................................................21
2.5.4 LCD Backlight Connector (J10)............................................21
2.5.5 ATX Power Connector (J7)..................................................22
2.5.6 USB3.0/2.0 Connector (J8, J9).............................................23
2.5.7 Dual USB 2.0 Connector (J16).............................................24
2.5.8 Front Panel Audio Connector (J18)......................................24
2.5.9 Front Panel Settings Connector (J3)....................................25
2.5.10 LVDS Connector (J11, J12).................................................26
2.5.11 Fan Power Connector (CPU_FAN1) ....................................27
2.5.12 DVI-D Connector (J20) .........................................................28
2.5.13 Parallel Port (J24).................................................................29
Chapter 3 Drivers Installation.............................................31
3.1 Introduction........................................................................................32
3.2 Intel®Chipset Software Installation Utility...........................................33
3.3 VGA Driver Installation.......................................................................35
3.4 HD Audio Driver Installation...............................................................38
3.5 LAN Driver Installation .......................................................................39
3.6 Intel®Management Engine Interface..................................................42

viii
IB995 User’s Manual
Chapter 4 BIOS Setup......................................................... 45
4.1 Introduction....................................................................................... 46
4.2 BIOS Setup....................................................................................... 46
4.3 Main Settings.................................................................................... 48
4.4 Advanced Settings............................................................................ 49
4.4.1 Connectivity Configuration................................................... 50
4.4.2 CPU Configuration............................................................... 51
4.4.3 PCH-FW Configuration........................................................ 52
4.4.4 Trusted Computing.............................................................. 53
4.4.5 ACPI Settings ...................................................................... 54
4.4.6 LVDS (eDP/DP) Configuration............................................. 55
4.4.7 F81964 Super IO Configuration ........................................... 56
4.4.8 F81964 Hardware Monitor ................................................... 57
4.4.9 USB Configuration............................................................... 58
4.4.10 Network Stack Configuration................................................ 59
4.4.11 CSM Configuration............................................................... 60
4.4.12 NVMe Configuration............................................................. 61
4.5 Chipset Settings................................................................................ 62
4.5.1 System Agent (SA) Configuration ........................................ 63
4.5.1.1 Graphics Configuration and VT-d Capability ........................ 63
4.5.2 PCH-IO Configuration.......................................................... 64
4.6 Security Settings............................................................................... 65
4.6.1 Secure Boot Configuration................................................... 66
4.6.1.1 Key Management................................................................. 67
4.7 Boot Settings .................................................................................... 69
4.8 Save & Exit Settings.......................................................................... 70
Appendix........................................................................................ 71
A. I/O Port Address Map........................................................................ 72
B. Interrupt Request Lines (IRQ)........................................................... 73
C. Watchdog Timer Configuration.......................................................... 74

1
Chapter 1
General Information
The information provided in this chapter includes:
•Features
•Packing List
•Optional Accessories
•Block Diagram
•Specifications
•Board Overview
•Board Dimensions

2
IB995 User’s Manual
1.1 Introduction
The IB995AF PICMG1.3 SHB Express CPU Card is based
on the latest 8th or 9th Gen. Intel® Xeon® E / Core™ /
Pentium® / Celeron® processor with speeds of up to 4.7GHz
and features an integrated graphics core that work with
LVDS, DVI-I and DVI-D display outputs.
IB995 utilizes the dramatic increase in performance provided
by Intel’s latest cutting-edge technology. Measuring 338mm
x122mm, IB995 offers fast 6Gbps SATA support (up to 8
ports), USB3.1 (5 ports) and interfaces for two Gigabit LAN.
Photo of IB995
1.2 Features
•2 x DDR4-2400/2666 UDIMM, expandable up to 32GB, ECC
supported per CPU SKUS.
•Dual Gigabit LAN
•1 x DVI-I , 1 x DVI-D, 1 x 24-bit dual channel LVDS
•5 x USB 3.1, 8 x SATA III, 4 x serial ports
•PCIe (x16), M.2 M2280 (for IB995AF series only) and M.2 E2230
expansion slots
•Configurable watchdog timer, digital I/O, TPM

General Information
IB995 User’s Manual
3
1
1.3 Packing List
Your IB995 package should include the items listed below. If any of
the items is missing, please contact the distributor or dealer from
whom you have purchased the product.
•IB995AF PICMG1.3 SHB x 1
•I/O shield
•SATA cable (SATA-5)
•COM port cable (PK1-150)
•Disk (including chipset drivers)
•This user’s manual
1.4 Optional Accessories
•Audio cable (Audio-34)
•DVI-D cable (DVIK-3)
•USB cable (USB-29)
•USB3.0 cable (USB-3K)
•Printer port cable (PK3K)

4
IB995 User’s Manual
1.5 Specifications
Product
Name
IB995AF Series
IB995EF
Form Factor
PICMG 1.3 SHB Express full size CPU card
System
Operating
System
•Microsoft Windows 10 (64-bit)
•Linux Ubuntu (64-bit)
CPU &
Chipset
9th / 8th Gen. Intel®Xeon®E / Core™ / Pentium®/
Celeron® , up to 4.7 GHz
Memory
2 x DDR4 UDIMM 2666 / 2400 MHz, up to 32 GB
*ECC will be supported by identified CPU SKUs.
Storage
M.2 M2280 slot (NVMe
supported)
N/A
Graphics
Intel®UHD Graphics P630
LAN
1st LAN: Intel®I219LM GbE
2nd LAN: Intel®I210AT /
I211AT GbE
1st LAN: Intel®I219V GbE
2nd LAN: Intel®I211AT GbE
Security
TPM 2.0
Super I/O
Fintek F81964D-I
Digital I/O
4-In / 4-Out
Audio
Codec
Built HD audio with Realtek ALC662
Watchdog
Timer
Yes (256 segments, 0, 1, 2…255 sec / min)
BIOS
AMI BIOS
iSmart
N/A
RAID
RAID 0/1/5
N/A
iAMT
11.6 (with E-Xeon®/ Core i7/ i5
DT CPU SKUs)
N/A
TPM
2.0
Dimensions
338mm x 126mm
RoHS
Yes
Certification
CE, FCC

General Information
IB995 User’s Manual
5
1
Model
IB995AF Series
IB995EF
I/O Ports
Display
•1 x DVI-D (1920 x 1080 at 60 Hz)
•1 x DVI-I (1920 x 1080 at 60 Hz)
•1 x 24-bit dual channel LVDS (1920 x 1080 at 60 Hz)
LAN
•2 x RJ45 GbE LAN
•1 x M.2 (E-key@2230), Support CNVi
USB
•1 x USB 3.1 (I/O coastline
connectors)
•4 x USB 3.1 (via two onboard
pin-header)
•1 x USB 2.0 ports (via M.2
E2230)
•1 x USB 2.0 (Vertical type A)
•2 x USB 2.0 (via an onboard
pin-header)
•4 x USB 2.0 to Backplane
•1 x USB 3.1 (I/O
coastline connectors)
•1 x USB 2.0 (Vertical
type A)
•4 x USB 2.0 to
Backplane
Serial
4 x COM ports:
•COM1: RS-232/422/485
(Support Ring-in with power
at 500mA, selectable for 5V
or 12V)
•COM2 ~ COM4: RS-232 only
(via onboard box-headers)
4 x COM ports:
•COM1: RS-232/422/485
(Support Ring-in with
power at 500mA,
selectable for 5V or 12V)
•COM2 ~ COM4: RS-232
only (via onboard
box-headers))
SATA
•IB995AF-C246 support 8 ports, 5 x SATAIII (3.0) 6Gbps
•IB995AF(Q370) support 6 ports, 3 x SATAIII (3.0) 6Gbps
•IB995EF(H310); support 4 ports, 2 x SATAIII (3.0) 6Gbps
Digital IO
4-In & 4-Out
Expansion
Slots
•1 x PCIe (x16)
•1 x M.2 M2280
•1 x M.2 E2230
•1 x PCIe (x16)
•1 x M.2 E2230
Environment
Temperature
•Operating: 0 ~ 60 °C (32 ~ 140 °F)
•Storage: -20 ~ 80 °C (-4 ~ 176 °F)
Relative Humidity
0 ~ 90 %, non-condensing at 60 °C
All specifications are subject to change without prior notice.

6
IB995 User’s Manual
1.6 Block Diagram

General Information
IB995 User’s Manual
7
1
1.7 Board Pictures
Top View
Bottom View
I/O View
＊The photos above are for reference only.

8
IB995 User’s Manual
1.8 Dimensions

9
Chapter 2
Hardware Configuration
This section provides information on jumper settings and
connectors on the IB995 in order to set up a workable system.
On top of that, you will also need to install crucial pieces such as
the CPU and the memory before using the product. The topics
covered are:
•Essential installations before you begin:
CPU and the memory
•Jumper and connector locations
•Jumper settings and information of connectors

10
IB995 User’s Manual
2.1 Essential Installations Before You Begin
Follow the instructions below to install the CPU and the memory.
2.1.1 Installing the CPU
The IB995 board supports an LGA1151 Socket (shown below) for
Intel®Xeon®E3 v5 family or Intel®6th Gen. CoreTM i7 / i5 / i3 DT
processor processors. Follow the instructions below to install the
CPU.
1. Unlock the socket by pressing the lever sideways, then lift up the
lever and the metal lid.
2. Position the CPU above the socket such that the CPU corner
aligns with the gold triangle matching the socket corner with a
small triangle.
3. Carefully insert the CPU into the socket and push down the lever
to secure the CPU.
Then you can install the CPU cooler and fan.
Note: Ensure that the CPU cooler and the CPU top surface are in total
contact to avoid CPU overheating problem that would cause your
system to hang or be unstable.

Hardware Configuration
IB995 User’s Manual
11
2
2.1.2 Installing the Memory
The IB995 board supports two DDR4 memory socket for a maximum
total memory of 32GB in DDR4 UDIMM memory type. To install the
modules, locate the memory slot on the board and perform the
following steps:
1. Hold the module so that the key of the module aligned with that
on the memory slot.
2. Gently push the module in an upright position until the clips of the
slot close to hold the module in place when the module touches
the bottom of the slot.
To remove the module, press the clips outwards with both hands

12
IB995 User’s Manual
2.2 Setting the Jumpers
Set up and configure your IB995 by using jumpers for various settings
and features according to your needs and applications. Contact your
supplier if you have doubts about the best configuration for your use.
2.2.1 How to Set Jumpers
Jumpers are short-length conductors consisting of several metal pins
with a non-conductive base mounted on the circuit board. Jumper
caps are used to have the functions and features enabled or
disabled. If a jumper has 3 pins, you can connect either PIN1 to PIN2
or PIN2 to PIN3 by shorting.
Pin# 1 23
A 3-pin jumper
A jumper cap
Refer to the illustration below to set jumpers.
Pin closed
Oblique view
Illustration
Open
1 2 3
1-2
1 2 3
2-3
1 2 3
When two pins of a jumper are encased in a jumper cap, this jumper
is closed, i.e. turned On.
When a jumper cap is removed from two jumper pins, this jumper is
open, i.e. turned Off.