IBASE Technology IP414 User manual

IP414
ATX COM Express Type 6 Baseboard
User’s Manual
Version 1.0
(July 2023)

ii
IP414 User’s Manual
Copyright
©2023 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval system,
translated into any language or transmitted in any form or by any means,
electronic, mechanical, photocopying, or otherwise, without the prior written
consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the products
described in this document without prior notice. Every effort has been made to
ensure the information in the document is correct; however, IBASE does not
guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising from
misapplication or inability to use the product or the information contained herein,
nor for any infringements of rights of third parties, which may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for
identification purposes only and may be trademarks and/or registered trademarks
of their respective owners.

IP414 User’s Manual
iii
Compliance
In a domestic environment, this product may cause radio interference in which
case users may be required to take adequate measures.
This product has been tested and found to comply with the limits for a Class A
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with manufacturer’s instructions, may cause
harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household
waste, in accordance with the EU directive of for waste
electrical and electronic equipment (WEEE - 2012/19/EU).
Instead, it should be disposed of by returning it to a
municipal recycling collection point. Check local
regulations for disposal of electronic products.
Green IBASE
This product is compliant with the current RoHS
restrictions and prohibits use of the following substances in
concentrations exceeding 0.1% by weight (1000 ppm)
except for cadmium, limited to 0.01% by weight (100 ppm).
•Lead (Pb)
•Mercury (Hg)
•Cadmium (Cd)
•Hexavalent chromium (Cr6+)
•Polybrominated biphenyls (PBB)
•Polybrominated diphenyl ether (PBDE)

iv
IP414 User’s Manual
Important Safety Information
Carefully read the precautions before using the board.
Environmental conditions:
•Use this product in environments with ambient temperatures between 0˚C
and 60˚C.
•Do not leave this product in an environment where the storage temperature
may be below -20°C or above 80°C. To prevent from damages, the product
must be used in a controlled environment.
Care for your IBASE products:
•Before cleaning the PCB, unplug all cables and remove the battery.
•Clean the PCB with a circuit board cleaner or degreaser, or use cotton swabs
and alcohol.
•Vacuum the dust with a computer vacuum cleaner to prevent the fan from
being clogged.
WARNING.
Attention during use:
•Do not use this product near water.
•Do not spill water or any other liquids on this product.
•Do not place heavy objects on the top of this product.
Anti-static precautions
•Wear an anti-static wrist strap to avoid electrostatic discharge.
•Place the PCB on an anti-static kit or mat.
•Hold the edges of PCB when handling.
•Touch the edges of non-metallic components of the product instead of the
surface of the PCB.
•Ground yourself by touching a grounded conductor or a grounded bit of metal
frequently to discharge any static.
CAUTION
Danger of explosion if the internal lithium-ion battery is replaced by an incorrect
type. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s
instructions or recycle them at a local recycling facility or battery collection point.

IP414 User’s Manual
v
Warranty Policy
•IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of shipment
cannot be ascertained, the product serial numbers can be used to determine
the approximate shipping date.
•3rd-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are not
manufactured by IBASE, such as CPU, CPU cooler, memory, storage
devices, power adapter, panel and touchscreen.
＊PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE
TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED
FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest information
about the product.
2. If you need any further assistance fromyour distributor or sales representative,
prepare the following information of your product and elaborate upon the
problem.
•Product model name
•Product serial number
•Detailed description of the problem
•The error messages in text or in screenshots if there is any
•The arrangement of the peripherals
•Software in use (such as OS and application software, including the
version numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and
contact your distributor or sales representative.

vi
IP414 User’s Manual
Table of Contents
Chapter 1 General Information.............................................1
1.1 Introduction .........................................................................................2
1.2 Features..............................................................................................2
1.3 Specifications......................................................................................3
1.4 Board View..........................................................................................5
1.5 Dimensions .........................................................................................7
Chapter 2 HardwareConfiguration..........................................8
2.1 Setting the Jumpers.............................................................................9
2.2 Connector Locations on IP414...........................................................10
2.3 Jumpers Quick Reference.................................................................11
2.3.1 LVDS Panel Power (JP1)....................................................11
2.3.2 eDP / LVDS Selection (JP2)................................................12
2.3.3 eDP Panel Brightness Selection (JP3).................................13
2.3.4 LVDS Backlight Power Selection (JP4)................................14
2.3.5 eDP Panel Power (JP5).......................................................15
2.4 Connectors Quick Reference.............................................................16
2.4.1 USB 3.0 Connector (CN1, CN5)...........................................17
2.4.2 DisplayPort (CN2, CN3, CN4) ..............................................18
2.4.3 2.5G Gigabit LAN (CN6).......................................................19
2.4.4 SATA Connectors (CN7, CN8, CN9, CN10) .........................20
2.4.5 LVDS Connector (CN11, CN12)..........................................21
2.4.6 eDP Connector (CN13) ........................................................22
2.4.7 DC-In Power DIN 4P 8V~20V Input (CN14)..........................23
2.4.8 Fan Power Connector (CPU_FAN1, SYS_FAN1).................24
2.4.9 VGA Port (VGA1).................................................................25
2.4.10 SATA Power Connector (J2, J3)...........................................26
2.4.11 COM1 & COM2 RS-232 Ports (J6, J5) .................................27
2.4.12 M.2 M-Key 2280 (J7)............................................................28
2.4.13 USB 2.0 Connector (J9) .......................................................30
2.4.14 M.2 E-Key (2230) Connector PCIe (x1), USB 2.0 (J10)........31
2.4.15 Panel Inverter Power Connector (J11).................................32
2.4.16 M.2 B-Key (3052) Connector PCIe (x1), USB 2.0,
USB 3.0 SIM Card (J16).......................................................33
2.4.17 System Function Connector ( J17) .......................................34
2.4.18 Digital I/O Connector (J18)...................................................35

IP414 User’s Manual
vii
2.4.19 COM3 & COM4 RX/TX Port (J19, J20).................................36
2.4.20 ATX Power Connector (J23).................................................37
2.4.21 ATX 12V Power Connector (J24)..........................................38
2.4.23 PCIe (x4) Slot (PCIE1, PCIE2).............................................39
2.4.24 PCIe (x16) Slot (PCIEX16)...................................................40
2.4.25 PCIe (x1) Slot (PCIE3, PCIE4) .............................................41

viii
IP414 User’s Manual
This page is intentionally left blank.

1
Chapter 1
General Information
The information provided in this chapter includes:
•Features
•Specifications
•Board View
•Board Dimensions

2
IP414 User’s Manual
1.1 Introduction
IP414 / IP414-DC is a carrier board with ATX form factor for COM Express Type 6
CPU module; it is compatible with the ET980 COMe module and features
expansion slots including PCIe (x1), PCIe (x4) PCIe (x16) and M.2 E-Key / B-Key /
M-Key and video outputs (eDP / LVDS, DP++, VGA).
IP414
1.2 Features
•Supports 2x PCIe (x1) 2x PCIe (x4)and 1x PCIe (x16)
•Data transmission and I/O ports: USB 3.0, USB 2.0, 2.5Gb LAN, DisplayPort,
audio
•On-board headers for serial ports and eDP / LVDS / audio derived from the
COMe module ET980

General Information
IP414 User’s Manual
3
1
1.3 Specifications
Models
•IP414 (supports ATX Power)
•IP414-DC (supports DC-In)
Form Factor
ATX COM Express Type 6 baseboard
Dimensions
305 x 244 mm (12” x 9.61”)
RoHS
Yes
I/O Ports / Connectors
Power
•ATX Power
•DC-In (If your CPU module supports 12V only,
please use a 12V power adaptor to avoid
malfunction or any damage to your equipment.)
Video Output
•3x DisplayPort
•1x VGA
•1x 24-bit dual channel LVDS
•1x eDP
LAN
•Derived from COMe module as 2.5GbE #1
USB
•Derived from COM Express module
•2x USB 2.0 ports (2 for USB 2.0 @ M.2, 2 for
internal box headers)
•1x USB 2.0 port
•3 x USB 3.2 ports (3 for standard USB 3.2 @
edge I/O)
SATA
•4 for SATA 3.0 [blue] connector
Serial
•COM1 / COM2 (DF11 2x5 box header)
(from Super I/O)
•COM3 / COM4 (DF11 2x5 box header)
(from COMe, Tx/Rx only, TTL)
Audio
•ALC888S
•DF11 2x6 pin box header

4
IP414 User’s Manual
Battery for
RTC/CMOS
1 x Lithium battery cell for RTC of COM Express
module
Mini Type Slots
•1x M.2 (B3052)
•1x M.2 (M2080)
•1x M.2 (E2230)
Expansion
Slots
•1 x PCIe (x16) slot
•2 x PCIe (x4) slot
•2 x PCIe (x1) slot
Environment
Temperature
•Operation: 0 ~ 60 °C
•Storage: -20 ~ 80 °C
Relative
Humidity
10 ~ 90 %
All specifications are subject to change without prior notice.

General Information
IP414 User’s Manual
5
1
Board View
Top View
IP414
IP414-DC

6
IP414 User’s Manual
I/O View
No.*
Connector
1
DP connector x 3
2
USB 3.2 connector x 2
3
USB 3.2 + USB 2.0
Type A stack connector
4
RJ45 connector (2.5G)
* Listed from left to right positions.
DC-In Power DIN 4P 8V~20V Input
*Warning: The DC-in power connector can be used only with COM Express
Modules that supports modules 8V~20V power. If your CPU module supports 12V
only, please use a 12V power adaptor to avoid malfunction or any damage to your
equipment (e.g., ET980).

General Information
IP414 User’s Manual
7
1
1.4 Dimensions

8
Chapter 2
Hardware Configuration
This section provides information on jumper settings and connectors
on the IP414 in order to set up a workable system.
•Jumper and connector locations
•Jumper settings and information of connectors

Hardware Configuration
IP414 User’s Manual
9
2
2.1 Setting the Jumpers
Set up and configure your IP414 by using jumpers for various settings and features
according to your needs and applications. Contact your supplier if you have doubts
about the best configuration for your use.
2.2.1 How to Set Jumpers
Jumpers are short-length conductors consisting of several metal pins with a
non-conductive base mounted on the circuit board. Jumper caps are used to have
the functions and features enabled or disabled. If a jumper has 3 pins, you can
connect either PIN1 to PIN2 or PIN2 to PIN3 by shorting.
Pin# 1 23
A 3-pin jumper
A jumper cap
Refer to the illustration below to set jumpers.
Pin closed
Oblique view
Illustration
Open
1 2 3
1-2
1 2 3
2-3
1 2 3
When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e.
turned On.
When a jumper cap is removed from two jumper pins, this jumper is open, i.e.
turned Off.

10
IP414 User’s Manual
2.2 Connector Locations on IP414

Hardware Configuration
IP414 User’s Manual
11
2
2.3 Jumpers Quick Reference
Function
Jumper
Page
LVDS Panel Power
JP1
11
eDP / LVDS Selection
JP2
12
eDP Panel Brightness Selection
JP3
13
LVDS Backlight Power Selection
JP4
14
eDP Panel Power
JP5
15
2.3.1 LVDS Panel Power (JP1)
Function
Pin closed
Illustration
3.3V (default)
1-2
1
5V
2-3
1

12
IP414 User’s Manual
2.3.2 eDP / LVDS Selection (JP2)
Function
Pin closed
Illustration
eDP (default)
1-2
1
LVDS
2-3
1