IBASE Technology SP-63ER User manual

SP-63ER
8th Gen Intel® Core™
Video Wall Player with
MXM GTX1080 Graphics
User’s Manual
Version 1.0a
(January 2022)

ii
SP
-
63ER
User Manual
Copyright
© 2022 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval system, translated
into any language or transmitted in any form or by any means, electronic, mechanical,
photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc.
(hereinafter referred to as “IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the products described in
this document without prior notice. Every effort has been made to ensure the information in
the document is correct; however, IBASE does not guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising from
misapplication or inability to use the product or the information contained herein, nor for any
infringements of rights of third parties, which may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

SP
-
63ER
User Manual
iii
Compliance
In a domestic environment, this product may cause radio interference in which case
users may be required to take adequate measures.
This product has been tested and found to comply with the limits for a Class B
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with manufacturer’s instructions, may cause
harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household waste, in
accordance with the EU directive of for waste electrical and electronic
equipment (WEEE - 2012/19/EU). Instead, it should be disposed of by
returning it to a municipal recycling collection point. Check local
regulations for disposal of
electronic products.
Green IBASE
This product is compliant with the current RoHS restrictions and
prohibits use of the following substances in concentrations exceeding
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by
weight (100 ppm).
• Lead (Pb)
• Mercury (Hg)
• Cadmium (Cd)
• Hexavalent chromium (Cr6+)
• Polybrominated biphenyls (PBB)
• Polybrominated diphenyl ether (PBDE)

iv
SP
-
63ER
User Manual
Important Safety Information
Carefully read the precautions before using the device.
Environmental conditions:
 Lay the device horizontally on a stable and solid surface in case the device may
fall, causing serious damage.
 Leave plenty of space around the device and do not block the openings for
ventilation. NEVER DROP OR INSERT ANY OBJECTS OF ANY KIND INTO
THE VENTIILATION OPENINGS.
 Use this product in environments with ambient temperatures between 0˚C and
45˚C.
 DO NOT LEAVE THIS DEVICE IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY IS BELOW -20° C OR ABOVE 80° C. This
could damage the device. The device must be used in a controlled environment.
Care for your IBASE products:
 Before cleaning the device, turn it off and unplug all cables such as power in case
a small amount of electrical current may still flow.
 Use neutral cleaning agents or diluted alcohol to clean the device chassis with a
cloth. Then wipe the chassis with a dry cloth.
 Vacuum the dust with a computer vacuum cleaner to prevent the air vent or slots
from being clogged.
WARNING
Attention during use:
 Do not place heavy objects on the top of the device.
 Operate this device from the type of power indicated on the marking label. If you
are not sure of the type of power available, consult your distributor or local
power company.
 Do not walk on the power cord or allow anything to rest on it.
 If you use an extension cord, make sure that the total ampere rating of the
product plugged into the extension cord does not exceed its limits.
Avoid Disassembly
Do not disassemble, repair or make any modification to the device. Doing so could
generate hazards and cause damage to the device, even bodily injury or property
damage, and will void any warranty.

SP
-
63ER
User Manual
v
CAUTION
There is danger of explosion if internal lithium-ion battery is replaced by an incorrect
type. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
Warranty Policy
 IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of shipment
cannot be ascertained, the product serial numbers can be used to determine
the approximate shipping date.
 3rd-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are not
manufactured by IBASE, such as CPU, CPU cooler, memory, storage devices,
power adapter, panel and touchscreen.
＊ PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE
TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED
FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest information about
the product.
2. If you need any further assistance from your distributor or sales representative,
prepare the following information of your product and elaborate upon the
problem.
 Product model name
 Product serial number
 Detailed description of the problem
 The error messages in text or in screenshots if there is any
 The arrangement of the peripherals
 Software in use (such as OS and application software, including the version
numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and
contact your distributor or sales representative.

vi
SP
-
63ER
User Manual
Table of Contents
Chapter 1 General Information ................................................................. 1
1.1 Introduction ............................................................................................. 2
1.2 Features .................................................................................................. 2
1.3 Packing List ............................................................................................ 3
1.4 Specifications .......................................................................................... 3
1.5 Product View ........................................................................................... 4
1.6 Dimensions ............................................................................................. 6
Chapter 2 Hardware Installation & Motherboard Information .............. 7
2.1 Installation / Replacement ....................................................................... 8
2.1.1 Wall Mounting Bracket .............................................................. 8
2.1.2 Rack Mounting Ears ................................................................. 9
2.1.3 Top Cover ............................................................................... 10
2.1.4 SSD Storage .......................................................................... 11
2.1.5 Graphics Card ........................................................................ 12
2.1.6 Memory .................................................................................. 13
2.1.7 Mini-PCIe & M.2 Cards ........................................................... 13
2.2 Setting the Jumpers .............................................................................. 14
2.3 Jumper & Connector Locations on Motherboard ................................... 15
2.4.6 SW1 / J1 : ATX Power ON Switch ......................................................... 16
2.4.7 J2: M.2 B-key / SIM card slot ................................................................ 17
2.4.8 CN5 : SIM card SOCKET from J2 M.2 B-key ........................................ 17
2.4.9 J3: M.2 E-key ........................................................................................ 18
2.4.10 J4: Digital I/O Connector ....................................................................... 18
2.4.11 J5: 80 Port ............................................................................................ 19
2.4.12 J7: For Debug Use ................................................................................ 19
2.4.13 J8: Reset Button ................................................................................... 19
2.4.14 J9: For SPI Debug Tools Pin Header .................................................... 19
2.4.15 J10 / J11: DDR4 SO-DIMM Slots .......................................................... 20
2.4.16 J12 : ISMART MCU Program Header ................................................... 20
2.4.17 J13 : ATX Connector ............................................................................. 21
2.4.18 ATX_12V_2X1: ATX 12V Power Connector .......................................... 21
2.4.19 J14: Mini PCI-E Socket ......................................................................... 22
2.4.20 CN7: SIM Card Socket .......................................................................... 22
2.4.21 J15: MXM SRC Power .......................................................................... 22

SP
-
63ER
User Manual
vii
2.4.22 J16 : USB3.1 Connectors ...................................................................... 23
2.4.23 J17 : USB 2.0 Connector ...................................................................... 24
2.4.24 CN6: MXM Socket ................................................................................ 24
2.4.25 CN8, CN9: SATA Connectors ............................................................... 25
2.4.26 CPU_FAN1: CPU Fan Power Connector .............................................. 25
2.4.27 CN1: COM1 RS-232/422/485 Ports ...................................................... 26
2.4.28 CN2 / CN3: GbE LAN Port and Dual USB 3.1 Ports .............................. 26
2.4.29 CN4: Audio Connector .......................................................................... 27
2.4.30 LED1: Power LED / HDD LED .............................................................. 27
Chapter 3 Driver Installation ................................................................. 28
3.1 Introduction ........................................................................................... 29
3.2 Intel® Chipset Software Installation Utility .............................................. 29
3.3 NVIDIA Graphics Driver Installation ...................................................... 31
3.4 Realtek High Definition Audio Driver Installation ................................... 34
3.5 LAN Driver Installation .......................................................................... 36
3.6 Intel® Management Engine Components Drivers Installation ................. 38
Chapter 4 BIOS Setup ............................................................................ 40
4.1 Introduction ........................................................................................... 41
4.2 BIOS Setup ........................................................................................... 41
4.3 Main Settings ........................................................................................ 42
4.4 Advanced Settings ................................................................................ 42
4.5 Chipset Settings .................................................................................... 54
4.6 Security Settings ................................................................................... 59
4.7 Boot Settings......................................................................................... 61
4.8 Save & Exit Settings.............................................................................. 62
Appendix ...................................................................................................... 63
A. I/O Port Address Map ............................................................................ 64
B. Interrupt Request Lines (IRQ) ............................................................... 66
C. UMCC Quick Guide................................................ 錯誤! 尚未定義書籤。

1
Chapter 1
General Information
The information provided in this chapter includes:
 Features
 Packing List
 Accessories
 Specifications
 Product View
 Dimensions

2
SP
-
63ER
User Manual
1.1 Introduction
The SP-63ER is an 8th Gen Intel® Core™ Desktop Processor Video Wall
Player with Nvidia (GTX1080) MXM module and 16 HDMI outputs. It is the
perfect system for displaying 8K/12K video wall or menu boards. The platform
comes with built-in an MXM slot for installing the MXM GTX1080 graphics
module to power 16x HDMI 1.3 outputs. Its rugged design features Intel®
vPro™ and MARS technologies and advanced iSMART intelligent energy-
saving & Observer remote monitoring technologies.
1.2 Features
● Perfect for displaying 8K/12K video wall or menu board contents
● Supports 8th Gen Intel® Core™ desktop processors
● Up to 16 x HDMI 1.3 (w/o audio) with built-in hardware EDID emulation
function
● 1x MXM slot supports MXM GTX1080 16x HDMI 1.3
● Rugged design with Intel® vPro™ and MARS technologies
● iSMART intelligent energy-saving & Observer remote monitoring
technologies
● Supports display monitoring functions

General Information
SP
-
63ER
User Manual
3
1
1.3 Packing List
Your product package should include the items listed below.
 SP-63ER Digital Signage Player
Intel® Core™ i7-8700 Processor (12M cache, up to 3.2GHz), 1x MXM Nvidia
GTX 1080 8G GDDR5X GPU card, 16x HDMI, 2x 8GB DDR4-2666/2400 SO-
DIMM memory, 2x 128GB SATA III 2.5”HDD Dock, 850W PSU
 Power Cord
1.4 Specifications
Product SP-63ER
Mainboard MBD63E
Operating System Windows 10 IoT Enterprise 64-bit
CPU Intel® Core™ i7-8700 Processor (12M cache, up to
3.2GHz)
Chipset Intel® Q370PCH or Nvidia MXM Graphic card
Memory 2x 8GB DDR4-2666/2400 SO-DIMM memory
Graphics MXM Nvidia GTX 1080 8G GDDR5X GPU card,
LAN Controller 1x Intel® I219LM GbE, 1x Intel® I210AT GbE
Expansion Slots
1x Mini PCI-E;
1x M.2 (M-key, type:2280)
1x M.2 (E-key, type:2230);
1x MXM slot (for NVDIA module)
I/O Interface
16x HDMI 1.3 with hardware EDID emulation
4x USB 3.1 ports;
2x RJ45 for Gigabit LAN;
1x D-Sub for RS232
2x Audio connectors for Line-out/Mic-in
Power LED for power on/off & HDD
1x Power button
1x AC power inlet
Power Supply AC 110V~220V
Operating Temperature 0°C~ 45°C (32°F~113°F)
Storage Temperature -20°C ~ 80°C (-4°F~176°F)
Relative Humidity 5~90% @ 45°C, (non-condensing)
Vibration mSATA: 5 grms / 5~500Hz / random operation
Certification CE, FCC Class B, cULus,
Dimensions (W x H x D)
395mm(W) x 438mm(D) x 88mm(H)
15.5”(W) x 17.2”(D) x 3.46”(H)

4
SP
-
63ER
User Manual
1.5 Product View
Front View
No. Function No. Function
1 AC inlet (110V~220V) 5 Lin-out
2 1x D-Sub for RS232 6 Mic
3 2x GbE ports 7 HDD Activity and Power
LED
4 4x USB 3.1 ports 8 Power button
* Listed from left to right.
Rear View
* The number of HDMI ports will depend on the number of HDMI module tray
installed. This picture is for reference only.

General Information
SP
-
63ER
User Manual
5
1
Rear View
No. Part No. Part
1 Chassis Base 8 Backplance
2 Top Cover 9 2.5” SATA / HDD
3 Backplace Bracket 10 Power Supply
4 Base Cover Bracket 11 CPU Heatsink + Fan
5 4x HDMI Module Tray 12 12V Fan 60 x 60 x 15mm
6 2x 2.5” SATA Bracket 13 I/O Cobbecter Gasket
7 Motherboard

6
SP
-
63ER
User Manual
1.6 Dimensions
Unit: mm

7
Chapter 2
Hardware Installation &
Motherboard Information
The information provided in this chapter includes:
 Installations
 Wall Mounting Bracket
 Rack Mounting Ears
 Top Cover
 SSD Storage
 Graphics Card
 Memory
 Mini-PCIe & M.2 Cards
 Information and locations of connectors

8
SP
-
63ER
User Manual
2.1 Installation / Replacement
To install or replace internal parts or external accessories, follow the
instructions in the next pages.
2.1.1 Wall Mounting Bracket
Use the eight (8) screws shown below to install/ remove the wall
mounting bracket. The screw holes are located at the bottom of the
system.

Hardware Configuration
SP
-
63ER
User Manual
9
2
2.1.2 Rack Mounting Ears
Use the ten (10) screws shown below to install/ remove the rack
mounting ears.

10
SP
-
63ER
User Manual
2.1.3 Top Cover
To remove the top cover, remove the eight (8) screws shown below. The
top cover has to be removed when installing/replacing internal parts such
as the SSD storage or graphics card.

Hardware Configuration
SP
-
63ER
User Manual
11
2
2.1.4 SSD Storage
To replace or install the SSD storage, remove the top cover as shown in
the previous page and then remove the two (2) screws holding the SSD
storage kit.

12
SP
-
63ER
User Manual
2.1.5 Graphics Card
To replace or install the graphics card, remove the top cover as shown in
the previous page and then remove the four (4) screws holding the graphics
card kit as shown below.