IBASE Technology BYTEM-123-PC User manual

BYTEM-123-PC
Industrial Panel PC for Railway
User’s Manual
Version 1.0
(December 2020)

ii
BYTEM-123-PC User Manual
Copyright
©2016 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval system, translated
into any language or transmitted in any form or by any means, electronic, mechanical,
photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc.
(hereinafter referred to as “IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the products described in
this document without prior notice. Every effort has been made to ensure the information in
the document is correct; however, IBASE does not guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising from
misapplication or inability to use the product or the information contained herein, nor for any
infringements of rights of third parties, which may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

BYTEM-123-PC User Manual
iii
Compliance
This product has passed CE tests for environmental specifications and limits. This
product is in accordance with the directives of the Union European (EU). If users
modify and/or install other devices in this equipment, the CE conformity declaration
may no longer apply.
This product has been tested and found to comply with the limits for a Class B
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with manufacturer’s instructions, may cause
harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household waste, in
accordance with the EU directive of for waste electrical and electronic
equipment (WEEE - 2012/19/EU). Instead, it should be disposed of by
returning it to a municipal recycling collection point. Check local
regulations for disposal of electronic products.

iv
BYTEM-123-PC User Manual
Green IBASE
This product is compliant with the current RoHS restrictions and
prohibits use of the following substances in concentrations exceeding
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by
weight (100 ppm).
•Lead (Pb)
•Mercury (Hg)
•Cadmium (Cd)
•Hexavalent chromium (Cr6+)
•Polybrominated biphenyls (PBB)
•Polybrominated diphenyl ether (PBDE)
Important Safety Information
Carefully read the precautions before using the device.
Environmental conditions:
Lay the device horizontally on a stable and solid surface during installation in
case the device may fall, causing serious damage.
Leave plenty of space around the device for ventilation.
Use this product in environments with ambient temperatures between -40˚C and
70˚C.
DO NOT LEAVE THIS DEVICE IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY BE BELOW -40°C OR ABOVE 85°C. To
prevent from damages, the device must be used in a controlled environment.
Keep the device away from humidity to avoid fog or condensation from
accumulating on the inner surface of the panel.
WARNING
Attention during use:
Do not use this product near water.
Do not spill water or any other liquids on your device.
Operate this device from the type of power indicated on the marking label. If you
are not sure of the type of power available, consult your distributor or local
power company.
If you use an extension cord, make sure that the total ampere rating of the
product plugged into the extension cord does not exceed its limits.
Avoid Disassembly
You are not suggested to disassemble, repair or make any modification to the device.
Disassembly, modification, or any attempt at repair could generate hazards and
cause damage to the device, even bodily injury or property damage, and will void any
warranty.
Attention during use:

BYTEM-123-PC User Manual
v
Warranty Policy
IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of shipment
cannot be ascertained, the product serial numbers can be used to determine
the approximate shipping date.
3rd-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are not
manufactured by IBASE, such as CPU, CPU cooler, memory, storage devices,
power adapter, panel and touchscreen.
＊Products, however, that fail due to misuse, accident, improper installation or
unauthorized repair shall be treated as out of warranty and customers shall be
billed for repair and shipping charges.

vi
BYTEM-123-PC User Manual
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest information about
the product.
2. If you need any further assistance from your distributor or sales representative,
prepare the following information of your product and elaborate upon the
problem.
Product model name
Product serial number
Detailed description of the problem
The error messages in text or in screenshots if there is any
The arrangement of the peripherals
Software in use (such as OS and application software, including the version
numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and
contact your distributor or sales representative.

BYTEM-123-PC User Manual
vii
Table of Contents
Compliance....................................................................................................iii
Important Safety Information.......................................................................iv
WARNING ......................................................................................................iv
Warranty Policy..............................................................................................v
Technical Support & Services .....................................................................vi
Chapter 1 General Information................................................................1
1.1 Introduction.............................................................................................2
1.2 Features..................................................................................................2
1.3 Packing List ............................................................................................3
1.4 Specifications..........................................................................................4
1.5 Overview.................................................................................................6
1.6 Dimensions.............................................................................................8
Chapter 2 Hardware Installation & Motherboard Information ............10
2.1 Hardware Installation ............................................................................11
2.1.1 Membrane Keypad Extension.................................................11
2.1.2 Memory Installation ................................................................14
2.1.3 VESA Mount & Wall Mount Installation...................................15
2.2 Setting the Jumpers..............................................................................16
2.2.1 How to Set Jumpers ...............................................................16
2.3 Jumper & Connector Locations on Motherboard...................................17
2.4 Jumpers Quick Reference.....................................................................19
2.4.1 LVDS Panel Power Selection (J5)........................................19
2.4.2 LVDS Panel Brightness Control Selection (JP2) ..................20
2.4.3 ME Register Clearance (JP5)...............................................20
2.4.4 CMOS Data Clearance (JP6)...............................................21
2.5 Connectors Quick Reference................................................................22
2.5.1 Motherboard Power Button (SW1) .......................................23
2.5.2 LED Indicators for Power and HDD (LED1)..........................23
2.5.3 SATA II / mSATA Port (CN1) ...............................................23
2.5.4 SATA II Port (CN2)...............................................................24
2.5.5 USB 3.0 Port (CN3)..............................................................24
2.5.6 LAN Port (GbE) (CN4, CN5) ................................................24

viii
BYTEM-123-PC User Manual
2.5.7 USB 2.0 Port (CN6)..............................................................25
2.5.8 Display Port (CN7)...............................................................25
2.5.9 COM1 Port (RS-232/422/485) (CN8) ...................................26
2.5.10 Audio Connector (J1)...........................................................27
2.5.11 Amplifier Connector (J2) ......................................................27
2.5.12 DDR3L SO-DIMM Socket (J3, J7)........................................28
2.5.13 LVDS Connector (J4, J6) .....................................................28
2.5.14 SATA HDD Power Connector (J10) .....................................29
2.5.15 Smart Battery Connector (J11).............................................29
2.5.16 Full-Sized Mini-PCIe / mSATA Connector (J12)...................30
2.5.17 Half-Sized Mini-PCIe Connector (J13)..................................30
2.5.18 USB 2.0 Connector (J14).....................................................30
2.5.19 COM2 (RS-232) Port (J15)...................................................31
2.5.20 VGA Port (J16).....................................................................31
2.5.21 Digital I/O Connector (J17)...................................................32
2.5.22 Motherboard Power Input Connector (J18) ..........................32
2.5.23 Reset Switch Connector (J19)..............................................33
2.5.24 Power Switch Connector (J20).............................................33
2.5.25 LCD Backlight Connector (JP3)............................................34
2.5.26 System Fan Power Connector (SYS_FAN1)........................34
Chapter 3 Driver Installation .................................................................35
3.1 Introduction...........................................................................................36
3.2 Intel®Chipset Software Installation Utility..............................................37
3.3 VGA Driver Installation..........................................................................38
3.4 HD Audio Driver Installation..................................................................39
3.5 Intel®Trusted Execution Engine Installation..........................................40
Chapter 4 BIOS Setup............................................................................41
4.1 Introduction...........................................................................................42
4.2 BIOS Setup...........................................................................................42
4.3 Main Settings........................................................................................43
4.4 Advanced Settings................................................................................44
4.4.1 ACPI Settings.........................................................................45
4.4.2 LVDS Configuration................................................................46
4.4.3 iSMART Controller..................................................................47
4.4.4 Super IO Configuration...........................................................48
4.4.5 Hardware Monitor...................................................................49
4.4.6 CPU Configuration..................................................................50
4.4.7 CPU PPM Configuration.........................................................51
4.4.8 IDE Configuration...................................................................52

BYTEM-123-PC User Manual
ix
4.4.9 SDIO Configuration ................................................................53
4.4.10 USB Configuration..................................................................54
4.5 Chipset Settings....................................................................................55
4.5.1 North Bridge...........................................................................55
4.6 Security Settings...................................................................................56
4.7 Boot Settings.........................................................................................57
4.8 Save & Exit Settings..............................................................................58
Appendix ......................................................................................................59
A. I/O Port Address Map............................................................................60
B. Interrupt Request Lines (IRQ)...............................................................61
C. Digital I/O Sample Code........................................................................62
D. Watchdog Timer Configuration..............................................................67

1
Chapter 1
General Information
The information provided in this chapter includes:
Features
Packing List
Specifications
Overview
Dimensions

2
BYTEM-123-PC User Manual
1.1 Introduction
BYTEM-123-PC is a 12.1” industrial projected touch panel PC that is railway
compliant. With Intel®Atom™ E3845 Quad-Core based processor, the device
carries the level of IP65 ingress protection for the panel to provide good
quality of water-tight. The readability is especially enhanced for operating on
rolling shock on the railway. It is able to be operated at the ambient operating
temperature ranging from -40 to 70 °C, and even from -40 to 85 °C for
storage.
1.2 Features
Intel®Atom™ E3845 Quad-Core Processor
EN50155 certified railway application
24V DC power input, available options of 72V DC or 110V DC
IP65 protection for the front panel and IP54 for the whole unit
Projected capacitive touchscreen with optical bonding

General Information
BYTEM-123-PC User Manual
3
1
1.3 Packing List
Your BYTEM-123-PC package should include the items listed below. If any of
the items below is missing, contact the distributor or the dealer from whom
you purchased the product.
BYTEM-123-PC x 1
Keypad Cover x 1
Extension Cable (for Membrane Keypad) x 1
LAN Cable x 2
USB Cable x 1
Power Cable x 1
Disk x 1
Terminal Block x 1
Rack Mount Kit x 1
M3 Screw (for Rack Mount Kit) x 8
M4 Screw (for wall mount installation) x 6

4
BYTEM-123-PC User Manual
1.4 Specifications
Product Name
BYTEM-123-PC
System
Motherboard
IB897
Operating
System
Windows 8 (32-bit / 64-bit)
Windows 7 Pro for Embedded (64-bit)
Windows Embedded Standard 7 (64-bit)
CPU
Intel® Atom™ E3845 Quad-Core (1.91 GHz)
Chipset
Integrated
Memory
1 x DDR3L SO-DIMM 4 GB, expandable up to 8GB
Graphics
Intel®HD graphics Gen. 7 with 4EU
Supports DX 11, OGL 3.0, OCL 1.1, OGLES 2.0
Super I/O
Nuvoton NCT5523D
LVDS
Dual channel 24-bit
Audio Codec
Realtek ALC662, two-way audio
Membrane
Control
1 x Membrane Control Keypad
(Power, Brightness+, Brightness-, Volume+, Volume-, Power
LED, HDD LED)
Power Supply
24V DC-In
(Optional: 72V DC & 110V DC)
BIOS
AMI BIOS
Watchdog
Watchdog Timer 256 segments, 0, 1, 2…255 sec/min
iSMART
iSMART 2.0 (auto-scheduler / power resume)
Chassis
Aluminum front bezel and back cover
Mounting
VESA 75 x 75 mm
Dimensions
(W x H x D)
335 x 267 x 72.6 mm
(13.18” x 10.5” x 28.58”)
Net Weight
3.6 kg (7.94 lb)
Ingress
Protection
IP65 for front bezel
IP54 for the whole unit with I/O cover
Certificate
CE, FCC Class B, EN50155

General Information
BYTEM-123-PC User Manual
5
1
Panel
Display Type
12.1” TFT-LCD
Touch Type
Projected capacitive touch
Resolution
Max. 1024 x 768
Color
Max. 16.7M
View Angle
(H/V)
178°/ 178°
Light
Transmission
86 %
Luminance
500 cd/m2
Contrast
1000:1
Backlight
Lifetime
30000 hrs
I/O Ports
LAN
Intel®I210IT
2 x Gigabit Ethernet (RJ45)
2 x 10/100 Mbps LAN (M12 D-code)
USB
1 x USB 3.0
1 x USB 2.0 (Type A)
1 x USB 2.0 (M12 A-code)
Serial
1 x COM1 port (RS-232/422/485) for jumper-less selection
1 x COM2 (RS-232 only)
Storage
1 x 2.5” drive bay for SATA II HDD
SATA
2 x SATA II connector
Display
1 x Display Port
Audio
2 x internal speaker
Digital I/O
4 in & 4 out
Expansion
1 x Mini PCIe (x1) slot (half-sized) with USB
Environment
Temperature
Operating: -40 ~ 70 °C (-40 ~ 158 °F)
Storage: -40 ~ 85 °C (-40 ~ 185 °F)
Relative
Humidity
10 ~ 90% (non-condensing)
All specifications are subject to change without prior notice.

6
BYTEM-123-PC User Manual
1.5 Overview
Oblique View
No.
Name
No.
Name
1
Volume Control
4
LED Indicator for Power
2
Brightness Control
5
Power Button
3
LED Indicator for HDD

General Information
BYTEM-123-PC User Manual
7
1
Rear View
No.
Name
No.
Name
1
Additional Rack Mount Kit
4
LAN Port (10/100)
2
Power Port
The Pin definition of external
power cable as following:
5
I/O Cover
3
USB 2.0 Port

8
BYTEM-123-PC User Manual
I/O View
No.
Name
No.
Name
1
2.5” Drive Bay
4
LAN Port (GbE)
2
USB 2.0 Port
5
Display Port
3
USB 3.0 Port
6
COM Port
1.6 Dimensions
Unit: mm
Without Additional Rack Mount Kit

General Information
BYTEM-123-PC User Manual
9
1
With Additional Rack-Mount Kit

10
Chapter 2
Hardware Installation &
Motherboard Information
The information provided in this chapter includes:
Memory installation and membrane keypad extension
Information and locations of connectors