Icom Ve-pg2 User manual

RoIP GATEWAY

Installation guide q

VE-PG2

[Connecting a PC using an Ethernet cable]

Use an Ethernet crossover cable when connecting the

VE-PG2 to a PC, because the VE-PG2 does not have the

Ethernet straight/crossover cable automatic detect function.

Also, be careful of the cable polarity when connecting the

VE-PG2 to a HUB that does not have the Ethernet straight/

crossover cable automatic detect function. If the polarity is

wrong, the [LAN] LED will not light.

OPC-2073

Connection cable (For the transceiver)

OPC-2074

Connection cable (For the repeater)

The VE-PG2 has two operating modes, “Bridge mode (default)” and “Selective call mode.”“Bridge mode (default)” and “Selective call mode.”Bridge mode (default)” and “Selective call mode.”” and “Selective call mode.”and “Selective call mode.”“Selective call mode.”Selective call mode.””

• The transceiver connected to the VE-PG2 and transceiver to be called must be set to the same channel.

The VE-PG2s can be transmitted signals to the transceivers through the IP network.

In the Bridge mode has “Multicast mode” and “Unicast mode” operations.“Multicast mode” and “Unicast mode” operations.Multicast mode” and “Unicast mode” operations.” and “Unicast mode” operations.and “Unicast mode” operations.“Unicast mode” operations.Unicast mode” operations.” operations.operations.

• In the Multicast mode, the VE-PG2 calls all transceivers that are connected to the VE-PG2 (default).

• In the Unicast mode, the VE-PG2 calls a specified transceiver that is connected to the VE-PG2.

e e

If the channel for transceiver

A2 and transceiver A3 is set

to CH2, transceivers in Area

A can communicate with

transceivers in Area B.

If the channel for transceiver

B1 and transceiver B2 is set

to CH18, transceivers in

Area B can communicate

with transceivers in Area A.

[Area A] Specified Icom transceiver

Channel: CH2 Channel: CH18

Transceiver A1 Transceiver A2 Transceiver A3

[Area B] Specified Icom transceiver

Transceiver B1 Transceiver B2 Transceiver B3

network

VE-PG2

192.168.0.2

VE-PG2

192.168.0.3

[LAN] [LAN]

OPC-2073 OPC-2073

Transmission from transceiver A1 to transceiver B3.

Transmission from transceiver B3 to transceiver A1.

Example of the Bridge mode operation

[TRX1] [TRX1]

Channel: CH2

Transceiver A

Channel: CH18

Transceiver B

Example of the Bridge mode operation: Calling a transceiver in another area (Transceiver A1 calls Transceiver B3).

qSet Transceiver A1’s channel to CH2, and while holding down [PTT], speak into the microphone at your normal voice level

to call Transceiver B3.

wWhen Transceiver A receives the AF signal from Transceiver A1, Transceiver A sends the AF signal to the VE-PG2 through

the OPC-2073.

eThe VE-PG2 ([Area A]) converts the AF signal to an RoIP signal, then transmits it from the [LAN] port to the VE-PG2 ([Area

B]) through the IP network.

rThe VE-PG2 ([Area B]) converts the RoIP signal to an AF signal, then Transceiver B receives the signal.

tTransceiver B3 receives the signal from Transceiver B.

yTransceiver B3 can also transmit a signal to communicate with Transceiver A1.

CAUTION: Use only the specified cable to connect a transceiver or repeater to the VE-PG2. Using another cable, like an

Ethernet cable may damage the VE-PG2, transceivers or repeaters.

This installation guide describes the VE-PG2 operating

mode (Bridge mode and Selective call mode), and the

sample connection settings.

Read “Installation guide“Installation guideInstallation guide w” for the sample connectionfor the sample connection

setting details.

Download the VE-PG2 instruction manual from Icom web

site (http://www.icom.co.jp/world/), if necessary.

Transmits to all transceivers in the network

Example of the Multicast mode operation

Transmits to the specified transceiver in the network

Example of the Unicast mode operation

network

Transmits to all transceivers in the network

Example of the Multicast mode operation

Transmits to the specified transceiver in the network

Example of the Unicast mode operation

network

This guide describes about the preparation, operation

mode, connection, setting screen and IP address setting.

Read ““PRECAUTIONS” first if you have not read it.first if you have not read it.

Step1: Installation guide qStep2: Installation guide w

1. Preparation

Accessories Required items

Options

3. Operation mode

The DTMF tone code can be used for calling the specified station or controlling the external equipment in the Selective call

mode.

Example of the Selective call mode opration

Then starts communicating through the VE-PG2 A and VE-PG2 B.

VE-PG2 A transmits calling signal to the VE-PG2 B when DTMF code (example: “1”) is received.

(Transceiver A) (VE-PG2 A)

(VE-PG2 B)

(Transceiver B)

qTransmits a DTMF code (example: “1”) to communicate with Transceiver B through the IP network.

VE-PG2 finishes communicating when no audio is sent to transceivers A and B for 15 seconds.

Or, hold down transceiver’s [PTT] and [#] for 1 second to transmit a # DTMF signal from transceivers A or B.

network

2. Transceiver and repeater settings

Set the transceiver and repeater as shown in the following table before connecting to the VE-PG2.

Setting items Transceiver Repeater

Channel any any

Audio volume level Set the volume to the 12 o’clock position any

External I/O (D-sub 25) port setting*1– Ext. I/O 18 Output Low Voltage 2

Required optional connection cable*2OPC-2073 OPC-2074

*1The CS-FR5000 cloning software and OPC-1122U cloning cable are required when you set External I/O D-sub 25 port setting.

*2Use the specified connection cable when connecting the transceiver or repeater to the VE-PG2.

The following transceivers and repeaters are usable with the VE-PG2.

The optional connection cable is required, refer to the following table.

Model name Optional connection cable

IC-F121S/IC-F221S

OPC-2073 (approximately 5 m; 16.4 ft)

IC-F121/IC-F221

IC-F111S/IC-F211S

IC-F111/IC-F211

IC-FR5000/IC-FR6000 OPC-2074 (approximately 5 m; 16.4 ft)

Usable transceivers and repeaters

Bridge mode operation

Selective call mode operation

• AC adapter To set the VE-PG2, the following hardware and software are

required:

• PC (PC connected by an Ethernet cable)

Microsoft®Windows®XP, Microsoft®Windows Vista®or

Microsoft®Windows®7 is installed.

• Ethernet cable • Connection cable

• Ground wire (OPC-2073 or OPC-2074)

• Hub • Speciﬁed Icom transceiver

(100BASE-TX or faster products)

(The transceiver's instruction

manual)

+See “Installation guide w” for bridge and selective call mode setting examples.

Network and System default settings

Network setting IP address 192.168.0.1*

Subnet mask 255.255.255.0*

System setting

Administrator ID admin (Fixed)

Administrator

password wavemaster*

To set the VE-PG2 to the default setting, see “Precautions”“Precautions”Precautions””

for details.

*User settable.

4. Connection

Connect the Ethernet cable, HUB, the ground cable and AC adapter to the VE-PG2 by following steps qto ras shown

below.

(Connect the AC adapter with the VE-PG2 after connecting the Ethernet cable.)

• Disconnect the HUB from the established network before connecting the Ethernet cable, only if the VE-PG2 is in the default

mode.

• The VE-PG2 can be connected directly to the PC using the MDI-X (crossover) type Ethernet cable.

Set the static PC IP address (example: 192.168.0.100)

See the instruction manual which comes with the PC for

details on setting the PC IP address.

When you set the static VE-PG2 IP address, assign the IP

address by network administrator.

MODE DC LAN TRX1 TRX2 TRX3 IN

+ + +

OUT SW ABC

Connect the Ethernet cable

Start up the PC

Connect the AC adapter

to an AC outlet

Make sure the LEDs are lit.

To any unused

HUB port

HUB

To the VE-PG2 [LAN] port

To the DC jack

Supplied AC adapter VE-PG2

A Ethernet cable (purchase separately)

PC IP address

(example: 192.168.0.100)

12345

After turning the power ON, make sure [POWER], [LAN]

and [VoIP] are lit.

The LEDs light as a default or after resetting the VE-PG2.

POWER VoIP TRX1 TRX2 TRX3LAN EXT

CAUTION:

Connect the Ethernet cable to ONLY the

[LAN] port. If it is connected to [TRX1],

[TRX2] or [TRX3] port, the VE-PG2 and

HUB may be damaged.

GROUND

RWARNING!

To prevent electrical shock, television interference (TVI), broadcast interference (BCI) and other problems, ground the

VE-PG2 through the ground terminal.

For best results, connect a heavy gauge wire or strap to a ground terminal of an AC outlet or a long ground rod. Make

the distance between the ground terminal and ground as short as possible.

NEVER connect the ground terminal to a gas or electric pipe. This may result in an electrical shock or cause a fire.

Click “LAN IP” in the “Network setting” to display the“LAN IP” in the “Network setting” to display theLAN IP” in the “Network setting” to display the” in the “Network setting” to display thein the “Network setting” to display the“Network setting” to display theNetwork setting” to display the” to display theto display the

“LAN IP” setting screen.LAN IP” setting screen.” setting screen.setting screen.

5. Accessing the VE-PG2 setting screen

6. VE-PG2 IP address setting

Accessing the VE-PG2 setting screen

The following procedure describes how to access the

VE-PG2 setting screen from a web browser on the PC.

http://192.168.0.1/ Enter

Open a web browser, and then enter the VE-PG2 IP

address in the address bar.

Push [Enter]. The login authentication window will

open.

Enter “admin” (default user name) and “wavemaster”

(default password) in their respective input field, and

then click [OK] to display the VE-PG2 setting screen.

The factory default IP address setting is shown as an

example.

Setting screen descriptions

See the instruction manual (PDF file: Download from the

Icom web site) for details of the setting screen.

About web browsers

Only Microsoft Internet Explorer 8 or later should be used

with the VE-PG2.

Activate the JavaScript and set to allow Cookies on your

web browser to display the setting screen correctly.

If other browsers are used, the screen may not be

displayed correctly.

q Enter

wClick

q Link to Icom web site

Click the Icom logo to link to

the Icom web site if your PC

is connected to the Internet.

w Selects the setting

screen

Displays the screen name

list on a menu line. When

you place the mouse

pointer on each menu title,

a list of items drops down

which you can use to select

the desire setting.

(Example: Place the mouse

pointer on “Connection set-“Connection set-Connection set-

ting”, and then click “Oper-”, and then click “Oper-, and then click “Oper-“Oper-Oper-

ating mode” shown on the” shown on the

list.).)

e Setting items and

value display

Displays the setting and

values when you click the

screen name (example:

Clicking “Operating mode”“Operating mode”Operating mode””

displays the setting screen).

r Setting buttons

Save or cancel setting

values.

If “The setting which should“The setting which should

be rebooted was changed.”

is displayed on the screen

when you click the [Save]

button, click the [Save and

Reboot] button.

The VE-PG2 reboots, and

the setting items and values

are updated.

The following message is

displayed on the screen

while the VE-PG2 is reboot-

ing.

• The setting screen does

not automatically return,

so click [Back] about

30 seconds after the

“VE- PG2 is r eboot ing”VE-P G2 is re booti ng””

message appears.

Select

2Set the IP address and subnet mask of the VE-PG2.

Be sure not to input the same IP address as another

device’s address.

When you update the firmware online, connect the

VE-PG2 to the Internet and set the default gateway

and DNS server addresses as the addresses used

in the network.

When finished, click [Save and Reboot].

Setting the PC IP address

q Enter

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-6838W-2US Printed in Japan

wClick

VE-PG2 is rebooting.

Click [Back] after VE-PG2 has re-

booted.

Microsoft, Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States and/or other countries.

All other products or brands are registered trademarks or trademarks of their respective holders.

This product includes in GoAhead WebServer software of GoAhead Software Inc.

RoIP GATEWAY

Installation guide w

VE-PG2

Step1: Installation guide qStep2: Installation guide w

1. Connects transceivers and LAN to the VE-PG2

MODE DC LAN TRX1 TRX2 TRX3 IN

+ + +

OUT SW ABC

12345

MODE DC LAN TRX1 TRX2 TRX3 IN

+ + +

OUT SW ABC

To the [LAN] port

To the [TRX1] port

HUB

(192.168.0.2)

The [TRX1] port number: 21500

Connect the transceiver’s microphone connector and speaker jack.

NOTE: When using the repeater, connect the optional OPC-2074 to the repeater’s ACC connector.

Repeater’s rear panel

OPC-2074

ACC connector

[Area A]

[Area B]

Transceiver B

channel 2

Connect an Ethernet cable

VE-PG2

To the [TRX1] port

(192.168.0.3)

The [TRX1] port number: 21500

VE-PG2

To the [LAN] port

Connect the transceiver’s microphone connector and speaker jack.

Transceiver A

channel 2

Transceiver C

channel 10

Transceiver D

channel 10

NOTE: First, connect the transceiver

to the VE-PG2 using the optional

OPC-2073. Then turn ON the power

to the transceiver and the VE-PG2.

NOTE: First, connect the transceiver

to the VE-PG2 using the optional

OPC-2073. Then turn ON the power

to the transceiver and the VE-PG2.

Connect to the transceiver A’s speaker jack.

Connect to the transceiver C’s speaker jack.

CAUTION:

To connect the transceivers or repeaters, use only the following cables:

OPC-2073 (For the transceivers) or OPC-2074 (For the repeaters).

Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.

Using another cable, like an Ethernet cable may damage the VE-PG2,

transceivers or repeaters.

CAUTION:

To connect the transceivers or repeaters, use only the following cables:

OPC-2073 (For the transceivers) or OPC-2074 (For the repeaters).

Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.

Using another cable, like an Ethernet cable may damage the VE-PG2,

transceivers or repeaters.

MODE DC LAN TRX1 TRX2 TRX3 IN

+ + +

OUT SW ABC

Connect the optional OPC-2074 to

[TRX1], [TRX2] or [TRX3] only.

GROUND

Turn the transceivers’ power ON,

and then set the transceiver A

volume to the 12 o’clock position.

Turn the transceivers’ power ON,

and then set the transceiver C

volume to the 12 o’clock position.

If you connect the VE-PG2 to an

IP network, instead of the hub as

shown in this illustration, you can

communicate anywhere through

the IP network.

Set External I/O (D-sub 25) port setting* to Ext. I/O 18 Output Low Voltage 2.

*The CS-FR5000 cloning software and OPC-1122U cloning cable are required when you set External I/O D-sub 25 port setting.

• A static (fixed) IP address must be set to the VE-PG2, and connects as figure below. (Refer to the Installation guide qfor

details.)

• For the Unicast mode, after making the connections as illustrated below, set the VE-PG2 as described in the page to the

right.

• Refer to the Installation guide qfor details of the Multicast mode and the Unicast modes.

• Connect the VE-PG2 according to steps q– yin the illustration below.

Bridge mode setting

2 Sets the VE-PG2 to the Bridge mode (Unicast mode)

1. “IP communication mode setting” setting“IP communication mode setting” settingIP communication mode setting” setting” settingsetting

2.“IP network connection”–“Tranceiver 1 (TRX1)”setting“IP network connection”–“Tranceiver 1 (TRX1)”settingIP network connection”–“Tranceiver 1 (TRX1)”setting”–“Tranceiver 1 (TRX1)”setting–“Tranceiver 1 (TRX1)”setting“Tranceiver 1 (TRX1)”settingTranceiver 1 (TRX1)”setting”settingsetting

Set transceivers A and C AF volume to the 12 o’clock’clockclock

position.

3. Transceiver setting

4. How to communicate

While holding down transceiver D’s [PTT] of Area B,

speak into the microphone at your normal voice level

to reply to transceiver B in Area A.

Release transceiver D’s [PTT] to receive.

While holding down transceiver B’s [PTT] in Area A,

speak into the microphone at your normal voice level

to call transceiver D in Area B.

Release transceiver B’s [PTT] to receive.

Bridge mode setting

Turn transceivers B and D power ON, and select the

same operating channel as transceivers A and C.

• Set the same channel for all the transceivers, to

communicate with transceivers A and C.

See the transceiver’s instruction manual when

setting the channel, if necessary.

(Example) I n t h e i l l u s t r a t i o n t o t h e l e f t , s e t

transceiver A and B (Area A) to channel

2, and transceiver C and D (Area B) to

channel 10.

This setting example refers to the connections in the far top

left illustration.

This setting example refers to the connections in the far top

left illustration.

2.“IP network connection”–“Tranceiver 1 (TRX1)” setting (Continued)“IP network connection”–“Tranceiver 1 (TRX1)” setting (Continued)IP network connection”–“Tranceiver 1 (TRX1)” setting (Continued)”–“Tranceiver 1 (TRX1)” setting (Continued)–“Tranceiver 1 (TRX1)” setting (Continued)“Tranceiver 1 (TRX1)” setting (Continued)Tranceiver 1 (TRX1)” setting (Continued)” setting (Continued)setting (Continued)

Click [Connect] in “IP network connection status”,“IP network connection status”,IP network connection status”,”,,

and then confirm that “During transmit” appears in“During transmit” appears inDuring transmit” appears in” appears inappears in

“Status”.Status”.”..

This guide describes bridge and selective call mode

connection examples.

Read this guide after reading “Installation guide q”.

qAfter making the connections as shown to the

left, turn transceivers A and C power ON, then

open the setting screen with your browser (see

Installation guide q).

wClick “Operating mode” in the “Connection“Operating mode” in the “ConnectionOperating mode” in the “Connection” in the “Connectionin the “Connection“ConnectionConnection

setting”, and select “Unicast mode” in the”, and select “Unicast mode” in the, and select “Unicast mode” in the“Unicast mode” in theUnicast mode” in the” in thein the

“Transceiver 1 (TRX1):” of “IP communicationTransceiver 1 (TRX1):” of “IP communication” of “IP communicationof “IP communication“IP communicationIP communication

mode setting”.”..

eClick [Save and Reboot].

Select [Unicast mode] in both Area A and Area B.

Select

Click

Enter

Confirm

The dialog shown below appears, and then click [OK].

NOTE: “IP network connection” is initialized after“IP network connection” is initialized afterconnection” is initialized after” is initialized afteris initialized after

changing “IP communication mode setting”.“IP communication mode setting”..

Save the VE-PG2 setting as a setting file, if

necessary.

Refer to the instruction manual (PDF file:

Download from the Icom web site) for details.

Approximately 30 seconds after clicking [OK], move

the mouse pointer to [BACK] and click. After system

reboots, the setting screen will open.

qClick “Transceiver 1 (TRX1)” in “IP network“Transceiver 1 (TRX1)” in “IP networkTransceiver 1 (TRX1)” in “IP network” in “IP networkin “IP network“IP networkIP network

connection setting” in the “Connection setting”.” in the “Connection setting”.in the “Connection setting”.“Connection setting”.Connection setting”.”..

wInput the Connection IP address in the “IP network“IP networkIP network

connection”.”..

(Example) Input “192.168.0.3” to VE-PG2s in Area“192.168.0.3” to VE-PG2s in Area192.168.0.3” to VE-PG2s in Area” to VE-PG2s in Areato VE-PG2s in Area

A, and “192.168.0.2” to VE-PG2s in“192.168.0.2” to VE-PG2s in192.168.0.2” to VE-PG2s in” to VE-PG2s into VE-PG2s in

Area B illustrated to the left.

eClick [Save].

Click

“Connection IP address” for Area A ; “192.168.0.3”Connection IP address” for Area A ; “192.168.0.3”” for Area A ; “192.168.0.3”for Area A ; “192.168.0.3”“192.168.0.3”192.168.0.3””

“Connection IP address” for Area B ; “192.168.0.2”Connection IP address” for Area B ; “192.168.0.2”” for Area B ; “192.168.0.2”for Area B ; “192.168.0.2”“192.168.0.2”192.168.0.2””

Click “Connect” in both Area A and Area B.“Connect” in both Area A and Area B.Connect” in both Area A and Area B.” in both Area A and Area B.in both Area A and Area B.

Confirm “Status” in both Area A and Area B.“Status” in both Area A and Area B.Status” in both Area A and Area B.” in both Area A and Area B.in both Area A and Area B.

2 Sets the VE-PG2 to Selective call mode

1 Connects transceivers and LAN to the VE-PG2

MODE DC LAN TRX1 TRX2 TRX3 IN

+ + +

OUT SW ABC

GROUND

[TRX2] Calling number (DTMF): 2

To the [TRX2] port

To the [TRX1] port

(192.168.0.2)

[TRX1] Calling number (DTMF): 1

[Area A]

[Area B]

VE-PG2

Connect the transceiver’s microphone connector and speaker jack.

Transceiver A

channel 1

Transceiver C

channel 2

Transceiver B

channel 1

Transceiver D

channel 2

Connect the transceiver’s microphone connector and speaker jack.

NOTE: First, connect the transceiver

to the VE-PG2 using the specified

connection cable. Then turn ON the

power to the transceiver and the

VE-PG2.

NOTE: First, connect the transceiver

to the VE-PG2 using the specified

connection cable. Then turn ON the

power to the transceiver and the

VE-PG2.

CAUTION:

To connect the transceivers or repeaters, use only the following cables:

OPC-2073 (For the transceivers) or OPC-2074. (For the repeaters)

Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.

Using another cable, like an Ethernet cable or connect the cables to [LAN]

may damage the VE-PG2, transceivers or repeaters.

Turn the transceivers’ power ON,

and then set the transceiver A

volume to the 12 o’clock position.

Turn the transceivers’ power ON,

and then set the transceiver C

volume to the 12 o’clock position.

Connect to the transceiver’s speaker jack.

CAUTION:

To connect the transceivers or repeaters, use only the following cables:

OPC-2073 (For the transceivers) or OPC-2074. (For the repeaters)

Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.

Using another cable, like an Ethernet cable, or connecting the cables to

[LAN] may damage the VE-PG2, transceivers or repeaters.

NOTE: When using the repeater, connect the optional OPC-2074 to the repeater’s ACC connector.

Repeater’s rear panel

OPC-2074

ACC connector

MODE DC LAN TRX1 TRX2 TRX3 IN

+ + +

OUT SW ABC

Connect the specified cables to

[TRX1], [TRX2] or [TRX3] only.

Set External I/O (D-sub 25) port setting* to Ext. I/O 18 Output Low Voltage 2.

*The CS-FR5000 cloning software and OPC-1122U cloning cable are required when you set External I/O D-sub 25 port setting.

1. “Operating mode setting” setting“Operating mode setting” settingOperating mode setting” setting” setting

Select

Click

Selective call mode setting

5. How to communicate

Confirm the “Call destination number setting list” as“Call destination number setting list” asCall destination number setting list” as” asas

shown below.

NOTE:

• If you construct RoIP system with some VE-PG2s,

you can construct the system only to set each “Call“CallCall

destination number setting list”.”..

• “Call destination number setting list” has below 3“Call destination number setting list” has below 3Call destination number setting list” has below 3

buttons.

[Edit] : Click this button to edit the index setting.

[Delete] : Click this button to delete the index setting.

[Delete all] : Click this button to delete all data in the list.

2 Sets the VE-PG2 to Selective call mode (Continued)

This setting example refers to the connections in the far

top left illustration. Follow the steps for transceiver B calling

transceiver D.

qSet “Call destination number setting” for the Area“Call destination number setting” for the AreaCall destination number setting” for the Area” for the Areafor the Area

B shown to the left.

(Example) Set “Index” to “2”, “Call destination number”“Index” to “2”, “Call destination number”Index” to “2”, “Call destination number”” to “2”, “Call destination number”to “2”, “Call destination number”“2”, “Call destination number”2”, “Call destination number””, “Call destination number”, “Call destination number”“Call destination number”Call destination number””

to “2”, “Call destination VE-PG2 address”“2”, “Call destination VE-PG2 address”2”, “Call destination VE-PG2 address””, “Call destination VE-PG2 address”, “Call destination VE-PG2 address”“Call destination VE-PG2 address”Call destination VE-PG2 address””

to “192.168.0.2” and “Call destination“192.168.0.2” and “Call destination192.168.0.2” and “Call destination” and “Call destinationand “Call destination“Call destinationCall destination

VE-PG2 port” to “Transceiver 2(TRX2)”.” to “Transceiver 2(TRX2)”.to “Transceiver 2(TRX2)”.“Transceiver 2(TRX2)”.Transceiver 2(TRX2)”.”..

wClick [Save].

2. “Numbering plan” setting“Numbering plan” settingNumbering plan” setting” setting

qMove the mouse pointer to “Connection setting”,“Connection setting”,Connection setting”,”,,

and click “Numbering plan”.“Numbering plan”.Numbering plan”.”..

wSet “Call destination number setting” for the Area

A shown to the left.

(Example) Set “Index” to “1”, “Call destination number”“Index” to “1”, “Call destination number”Index” to “1”, “Call destination number”” to “1”, “Call destination number”to “1”, “Call destination number”“1”, “Call destination number”1”, “Call destination number””, “Call destination number”, “Call destination number”“Call destination number”Call destination number””

to “1”, “Call destination VE-PG2 address”“1”, “Call destination VE-PG2 address”1”, “Call destination VE-PG2 address””, “Call destination VE-PG2 address”, “Call destination VE-PG2 address”“Call destination VE-PG2 address”Call destination VE-PG2 address””

VE-PG2 port” to “Transceiver 1(TRX1)”.” to “Transceiver 1(TRX1)”.to “Transceiver 1(TRX1)”.“Transceiver 1(TRX1)”.Transceiver 1(TRX1)”.”..

eClick [Save].

qAfter making the connections as shown to the

above, turn transceivers A and C power ON, then

open the setting screen with your browser (see the

Installation guide q).

wClick the “Operating mode setting” in the“Operating mode setting” in theOperating mode setting” in the” in thein the

“Connection setting”, and then select “SelectiveConnection setting”, and then select “Selective”, and then select “Selective, and then select “Selective“SelectiveSelective

call mode”.”..

eClick the [Save and Reboot] button.

rClick [Back] on the screen after reboot finishes

(about 30 seconds later).

Click [OK] when the dialog box below appears.

• “Connection setting” will be return to default when“Connection setting” will be return to default whenConnection setting” will be return to default when” will be return to default whenwill be return to default when

the “Operating mode” setting is modified.“Operating mode” setting is modified.Operating mode” setting is modified.” setting is modified.setting is modified.

• Save the VE-PG2 setting to the setting file, if

necessary.

Refer to the VE-PG2 instruction manual (PDF file:

Download from the Icom web site) for details.

Hold down transceiver B’s [PTT], and push [2]

and [#] to transmit 2 and # DTMF signals to call to

transceiver D.

Release transceiver B’s [PTT] to receive.

Transceiver D sounds beep tone, then start

communication via the VE-PG2.

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-6838W-3US Printed in Japan

4. Transceiver setting

Turn transceivers B and D power ON, and select the

same operating channel as transceivers A and C.

• Set the same channel for all the transceivers, to

communicate with the transceivers A and C.

See the transceiver’s instruction manual when

setting the channel, if necessary.

(Example) I n t h e i l l u s t r a t i o n t o t h e l e f t , s e t

transceivers A and B (Area A) to channel

1, and transceivers C and D (Area B) to

channel 2.

This setting example refers to the connections in the far top

left illustration.

Select

Click

Enter

Select

Click

Enter

Select

Confirm

While holding down transceiver D’s [PTT], speak into

the microphone at your normal voice level.

Release transceiver D’s [PTT] to receive.

While holding down transceiver B’s [PTT], speak into

the microphone at your normal voice level.

Release transceiver B’s [PTT] to receive.

VE-PG2 finishes communication when no audio is

applied to transceivers B and D for 15 seconds. Or hold

down the transceiver’s [PTT] and [#] for 1 second to

transmit a # DTMF signal from the transceivers B or D.

3. Transceiver control setting

3. Transceiver control setting (Continued)

Select

Click

Selective call mode setting

Set transceivers A and C AF volume to the 12 o’clock’clockclock

position.

qMove the mouse pointer to “Connection setting”“Connection setting”Connection setting”

and then to the drop down menu “TRX/EXT”, then“TRX/EXT”, thenTRX/EXT”, then

click “Transceiver 1 (TRX1)”.

wSet “Calling notice tone to Transceiver” to “Notice“Calling notice tone to Transceiver” to “NoticeCalling notice tone to Transceiver” to “Notice“NoticeNotice

tone 2”.