Icop PEX-090T-8A User manual

i
DM&P Vortex86EX Panel
PC with 9” TFT LCD
Model:
PEX-090T-5A / PEX-090T-8A
User’s Manual
(Revision 1.1A)

i
Revision
Date Version Description
2016/11/18 Version 1.0 Initial Release
2017/01/10 Version 1.1 Specification correction

ii
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
Copyright
The information in this manual is subject to change without notice for
continuous improvement in the product. All rights are reserved. The manufacturer
assumes no responsibility for any inaccuracies that may be contained in this
document. And makes no commitment to update or to keep current the
information contained in this manual.
No part of this manual may be reproduced, copied, translated or transmitted,
in whole or in part, in any form or by any means without the prior written
permission of the ICOP Technology Inc.
Copyright 2017 ICOP Technology Inc.
Manual No. IUMPEX090-01 Ver.1.1A Jan, 2017
Trademarks Acknowledgment
Vortex86EXis the registered trademark of DMP Electronics Inc. Other brand
names or product names appearing in this document are the properties and
registered trademarks of their respective owners. All names mentioned herewith
are served for identification purpose only.
Safety Information
Read these Safety instructions carefully.
Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
Do not expose your Panel PC to rain or moisture, in order to prevent shock
and fire hazard.
Keep PEX-090T away from humidity.
Do not open the cabinet to avoid electrical shock. Refer to your nearest
dealer for qualified personnel servicing.
Never touch un-insulated terminals or wire unless your power adaptor is
disconnected.
Locate your Panel PC as close as possible to the socket outline for easy access
and to avoid force caused by entangling of your arms with surrounding cables
from the Panel PC.
USB connectors are not supplied with Limited Power Sources.
If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
DO NOT ATTEMPT TO OPEN OR TO DISASSEMBLE THE CHASSIS (ENCASING)OF THIS
PRODUCT.PLEASE CONTACT YOUR DEALER FOR SERVICING FROM QUALIFIED TECHNICIAN.

iii
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
Table of Contents
Table of Contents............................................................................................. iii
1.General Information ............................................................................. 1
1.1 Product Description............................................................ 1
1.2 Product Specification ......................................................... 2
1.3 Inspection standard for TFT-LCD Panel .............................. 4
1.4 Product Dimension............................................................. 7
1.5 Panel Mounting Instruction................................................ 8
1.6 Ordering Information ....................................................... 10
1.7 Packing List ....................................................................... 10
2.System Installation ............................................................................. 11
2.1 CPU Board Outline............................................................ 11
2.2 Connector Summary......................................................... 12
2.3 Connector Pin Assignments.............................................. 13
2.4 External I/O Overview ...................................................... 15
2.5 External I/O Pin Assignment............................................. 16
2.6 System Mapping............................................................... 18
2.7 Watchdog Timer............................................................... 21
3.Driver Installation ............................................................................... 22
3.1 PEX-090T Development Note........................................... 23
Warranty......................................................................................................... 24

1
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
1.General Information
1.1 Product Description
PEX-090T is an ultra-compact platform for the present demanding embedded
and productive applications. It has new Vortex86EX SoC CPU which consumes only
minimum power requirement when running at 400MHz, and DDR3 memory
provides faster data transfer rate. By using 9” TFT LCD, PEX-090T becomes the
perfect choice for a limited budget. In additional, the integrated 10/100M
Ethernet port supplies the communication capability which makes PEX-090T can
be more widely used when running with DOS, Linux, Windows CE, Windows
Embedded environments to become the perfect solution for system integration.

2
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
1.2 Product Specification
Table 1-1 Product Specification
CPU Board Specifications
CPU DM&P Vortex86EX - 400MHz
Cache
L1:16KB I-Cache, 16KB D-Cache
L2: 128KB Cache
BIOS Coreboot BIOS
Memory 1GB DDR3 onboard
Watchdog Timer
Software programmable from
30.5u to 512 seconds x 2 sets
LAN Integrated 10/100M Ethernet
Audio HD Audio-Realtek ALC262 CODEC
Internal Drives Micro SD slot
I/O
RS-232/422/485 x 1
USB ports (Ver2.0) x 2
RJ-45 Port x 1
Mechanical & Environment
Power Requirement
Single Voltage +5VDC ( 5A )
Multi Voltage +8~+35VDC ( 8A )
Power Consumption 10 Watt
Operating
Temperature -20~+60℃( -22 ~ +140℉)
Storage Temp. -30 ~ +70℃( 14 ~ +158℉)
Operating Humidity 0% ~ 90% relative humidity, non-condensing
Dimensions 236.6 x 146 x 35mm (9.31 x 5.75 x 1.38 inches)

3
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
Weight 760g
Front Panel
Protection
IP 65
Certification CE / FCC / VCCI / Vibration / Shock
LCD Specifications
Display Type 9” TFT LCD
Backlight Unit LED
Display Resolution 1024(W) x 600(H)
Brightness (cd/m2) 300 nits
Contrast Ratio 500 : 1
Display Color 262, 144
Pixel Pitch (mm) 190.5 (H) x 189 (V)
Viewing Angle
Vertical 120o,
Horizontal 140o
Backlight Lifetime 18,000 hrs
Touchscreen
Type Analog Resistive
Resolution Continuous
Transmittance 80%
Controller PS / 2 interface
Software Driver Linux, Win CE
Durability 1 million

4
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
1.3 Inspection standard for TFT-LCD Panel
Table 1-2 Inspection Standard
DEFECT TYPE LIMIT Note
VISUAL
DEFECT
INTER
NAL
SPOT
φ＜0.15mm Ignore
Note1
0.15mm≦φ≦0.5mm N≦4
0.5mm＜φN=0
FIBER
0.03mm<W≦0.1mm, L≦
5mm N≦3
Note1
1.0mm＜W, 1.5mm＜L N=0
POLARIZER
BUBBLE
φ＜0.15mm Ignore
Note1
0.15mm≦φ≦0.5mm N≦2
0.5mm＜φN=0
Mura It’ OK if mura is slight visible through 6%ND filter
ELECTRICAL
DEFECT
BRIGHT DOT
A Grade B Grade
C
Area
O
Area Total C Area
O
Area Total Note3
N≦0 N≦2 N≦2 N≦2 N≦3 N≦5 Note2
DARK DOT N≦2 N≦3 N≦3 N≦3 N≦5 N≦8
TOTAL DOT N≦4 N≦5 N≦6 N≦8 Note2
TWO ADJACENT DOT N≦0 N≦1
pair
N≦1
pair
N≦1
pair
N≦1
pair
N≦1
pair Note4
THREE OR MORE
ADJACENT DOT NOT ALLOWED
LINE DEFECT NOT ALLOWED
(1) One pixel consists of 3 sub-pixels, including R, G, and B dot.
(Sub-pixel = Dot)
(2) LITTLE BRIGHT DOT ACCEPTITABLE UNDER 6 % ND-Filter
(3) If require G0 grand (Total dot N≦0), please contact region sales.

5
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
[Note 1] W : Width[mm], L : Length[mm], N : Number, φ: Average Diameter.
1. White / Black Spot
2. Polarizer Bubble
Fig 1-1
Fig 1-2
[Note 2] Bright dot is defined through 6% transmission ND Filter as following.
Fig 1-3

6
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
[Note 3]
C Area: Center of display area
O Area: Outer of display area
[Note 4]
Judge defect dot and adjacent dot as following. Allow below (as A, B, C and D
status) adjacent defect dots, including bright and dart adjacent dot. And they will
be counted 2 defect dots in total quantity.
R
R
G
G
R G
R
R
G
G
R G
R
R
G
G
R G
R
R
G
G
R G
R
R
G
G
RG
R
R
G
G
R G
R
RDefect Dot
Adjacent Dot
A
B
C
D
(1) The defects that are not defined above and considered to be problem shall
be reviewed and discussed by both parties.
Defects on the Black Matrix, out of Display area, are not considered as a defect or
counted.

7
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
1.4 Product Dimension
Fig 1-4 Product Dimension

8
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
1.5 Panel Mounting Instruction
1. Cut a mounting hole in the panel. (Refer to PEX-090T Dimensions on
page 7) (Note 1)
2. Check and remove the twelve M3 screws in a diagonal pattern as
image below if necessary.
3. Place PEX-090T face-down on a clean, flat surface.
4. Slide the panel cutout around the back of PEX-090T, until the panel
rests directly on the gasket. Make sure the screw holes align with the
screw holes on PEX-090T.
5. The screw size is M3*L (L=wall thickness + 6.0mm) (Note 2)
6. Insert all twelve M3 screws into the screw holes. (Note 2)
7. Finger-tighten the M3 screws. Finish tightening the M3 screws in a
diagonal pattern using an M3 screw driver (see the image as below);
maximum torque 1.18Nm (12 kgf-cm).

9
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
Note 1:
It is strongly recommended that a professional machine shop cut the
mounting hole in the panel.
Note 2:
The length for all twelve M3 screws will be according to the thickness of
mounting panel. For example: The length of standard M3 screws for PEX-090T
is 6mm. If the thickness of your mounting panel is 3mm and washer thickness is
1mm, you have to use 10mm M3 screw.

10
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
1.6 Ordering Information
Table 1-3 Ordering Information
PART NUMBER DESCRIPTION
PEX-090T-5A 9” Panel PC w/512MB
DDR3 / 2USB / Line-Out / LAN / COM / MicroSD /
Power Adapter
PEX-090T-8A 9” Panel PC w/512MB
DDR3 / 2USB / Line-Out / LAN / COM / MicroSD /
8-35 DC Support
1.7 Packing List
Table 1-4 Packing List
PART NUMBER PACKAGE
PEX-090T-5A PEX-090T-5A Power-20W-3PIN
PEX-090T-8A PEX-090T-8A
WLAN KIT
(Optional)
USB-WLAN-IPEX-KIT
WIRELESS-ANTENNA-157
WIRELESS-CABLE-150MM

11
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
2.System Installation
2.1 CPU Board Outline
Fig 2-1 PEX CPU Board

12
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
2.2 Connector Summary
Table 2-1 Summary Table
Nbr Description Type of Connections Pin nbrs.
J3 USB External USB Connector 6-pin
J4 USB External USB Connector 6-pin
J5 USB (Optional) 2.0mm 5-pin wafer 5-pin
J8 PS/2 Keyboard 2.54mm 5-pin box header 5-pin
J9 PS/2Keyboard External Mini DIN Socket 6-pin
J10 COM1(RS232/422/485) External D-Sub Male Connector 9-pin
J14 VGA 2.0mm 10-pin box header 10-pin
J18 Micro SD Card Socket Micro SD socket
J23 Audio Line-Out 1.25mm Phone Jack
J24 Audio Mic-In 2.0mm 4-pin wafer 4-pin
J25 COM3 (TX, RX) 1.25mm 3-pin wafer 3-pin
J26 COM4 (TX, RX) 1.25mm 3-pin wafer 3-pin
J30 SOM CPU Board Socket SOM CPU Board Socket 200-pin
J31 4-Wires Touch connector 1.25mm 4-pin wafer 4-pin
J32 USB (WLAN Optional) Internal USB Connector 6-pin
RJ45 Ethernet External RJ45 Connector 8-pin
PWR Power Connector (5A) External Mini DIN Socket 3-pin
PWR Power Connector (8A) External Power Plug 2-pin

13
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
2.3 Connector Pin Assignments
J3: USB
Pin # Signal Name Pin # Signal Name
1 VCC 2 USBD2-
3 USBD2+ 4 GND
5 GND 6 GND
J4: USB
Pin # Signal Name Pin # Signal Name
1 VCC 2 USBD3-
3 USBD3+ 4 GND
5 GND 6 GND
J5: USB (Optional)
Pin # Signal Name
1 VCC
2 USBD1-
3 USBD1+
4 GND
5 GND
J8: PS/2 Keyboard
Pin # Signal Name Pin # Signal Name
1 KBCLK 2 KBDAT
3 NC 4 GND
5 VCC
J9: PS/2 Keyboard
Pin # Signal Name Pin # Signal Name
1 KBCLK 2 MSCLK
3 GND 4 KBDATA
5 MSDATA 6 VCC
7 GND 8 GND
9 GND
J10: COM1 RS232/422/485
(Change setting by BIOS)
Pin # Signal Name Pin # Signal Name
1
DCD1/
422TX- /
RS485-
2
RXD1 /
422TX+ /
RS485+
3
TXD1 /
422RX+
4
DTR1 /
422RX-
5 GND 6 DSR1
7 RTS1 8 CTS1
9 RI1

14
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
J14: VGA
Pin # Signal Name Pin # Signal Name
1 R OUT 2 GND
3 G OUT 4 GND
5 B OUT 6 GND
7 HSYNC 8 GND
9 VSYNCD 10 GND
J24: MIC-IN
Pin # Signal Name
1 MICVREF
2 GND
3 GND
4 MIC-IN
J25: COM3 (TX, RX)
Pin # Signal Name
1 GND
2 TXD3
3 RXD3
J26: COM4 (TX, RX)
Pin # Signal Name
1 GND
2 TXD4
3 RXD4
J31: 4-Wires Touch connector
Pin # Signal Name
1 Y-
2 X-
3 Y+
4 X+
J32: USB (WLAN Optional)
Pin # Signal Name Pin # Signal Name
1 VCC 2 USBD2-
3 USBD2+ 4 GND
5 GND 6 GND
PWR: Power Connector (5A)
Pin # Signal Name
1 +5V
2 GND
3 NC
4 GND
PWR: Power Connector (8A)
Pin # Signal Name
1 + 8 ~ 35V
2 GND

15
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
2.4 External I/O Overview
{ PEX-090T-8A }
Fig 2-2 PEX-090T-8A I/O overview
{ PEX-090T-5A }
Fig 2-3 PEX-090T-5A I/O overview
{Note}
1. WLAN is optional
2. COM1 RS232/422/485 is selected by BIOS. For RS422 or
RS485 signals, please contact your region sales for custom
BIOS .

16
PEX-090TDM&P Vortex86EX Panel PC with 9” WSVGA TFT LCD
2.5 External I/O Pin Assignment
Power Switch
Pin # Status
| ON
O OFF
Power Connector (5A)
Pin # Signal Name
1 +5V
2 GND
3 NC
Power Connector (8A)
Pin # Signal Name
1 +8 ~ 35V
2 GND
Audio Line-Out
Pin # Signal Name
1 GND
2 LOUTL
3 Open Touch
4 Open Touch
5 VREFOUT
USB Port
Pin # Signal Name
1 VCC
2 USB0-
3 USB0+
4 GND
5 GGND
6 GGND
PS/2 Keyboard
Pin # Signal Name
1 KBCLK
2 PMCLK
3 GND
4 KBDAT
5 PMDAT
6 SB5V