ICP DAS USA PCI-1202 Series Instructions for use

PCI-1202/1602/1800/1802
Hardware User’s Manual
Warranty
All products manufactured by ICP DAS are warranted against defective materials for a
period of one year from the date of delivery to the original purchaser.
Warning
ICP DAS assume no liability for damages consequent to the use of this product. ICP
DAS reserves the right to change this manual at any time without notice. The information
furnished by ICP DAS is believed to be accurate and reliable. However, no responsibility is
assumed by ICP DAS for its use, nor for any infringements of patents or other rights of third
parties resulting from its use.
Copyright
Copyright © 1998~1999 by ICP DAS. All rights are reserved.
Trademark
The names used for identification only may be registered trademarks of their respective
companies.
Version: 4.4 (Dec.2009, PMH-014-42) ---- 1

Table of Contents
1. INTRODUCTION ..............................................................................................................................................5
1.1 GENERAL DESCRIPTION .............................................................................................................................. 5
1.2 THE BLOCK DIAGRAMS............................................................................................................................... 6
1.3 FEATURES ................................................................................................................................................... 7
1.4 SPECIFICATIONS .......................................................................................................................................... 8
1.4.1 PCI-1202L/H/LU/HU............................................................................................................................ 8U
1.4.2 PCI-1602/1602F.................................................................................................................................... 9
1.4.3 PCI-1800/1802.................................................................................................................................... 10
1.4.4 Analog Input Range............................................................................................................................. 11
1.4.5 A/D Trigger Methods .......................................................................................................................... 13
1.5 APPLICATIONS ................................................................................................................................. 14
1.6 PRODUCT CHECK LIST............................................................................................................................... 14
2. HARDWARE CONFIGURATION ................................................................................................................15
2.1 BOARD LAYOUT......................................................................................................................................... 15
2.2 JUMPER SETTING........................................................................................................................................ 20
2.2.1 JP1 : A/D Input Type Selection........................................................................................................... 20
2.2.2 J1 : D/A Reference Voltage Selection ................................................................................................. 20
2.2.3 D/I Port Setting (PCI-1202HU/LU/1602U/1602FU only)................................................................. 20
2.3 DAUGHTER BOARDS .................................................................................................................................. 21
2.3.1 DB-1825.............................................................................................................................................. 21
2.3.2 DB-8225.............................................................................................................................................. 21
2.3.3 DB37 ................................................................................................................................................... 21
2.3.4 DN37................................................................................................................................................... 21
2.3.5 DB-16P Isolated Input Board.............................................................................................................. 22
2.3.6 DB-16R Relay Board........................................................................................................................... 23
2.3.7 DB-24PR Power Relay Board............................................................................................................. 24
2.4 ANALOG INPUT SIGNAL CONNECTION....................................................................................................... 25
2.5 THE CONNECTORS..................................................................................................................................... 29
3. I/O CONTROL REGISTER...........................................................................................................................32
3.1 HOW TO FIND THE I/O ADDRESS ............................................................................................................... 32
3.2 THE ASSIGNMENT OF I/O ADDRESS........................................................................................................... 33
3.3 THE I/O ADDRESS MAP ............................................................................................................................. 33
3.4 SECTION 1: PCI CONTROLLER ................................................................................................................... 35
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver.4.2, Dec/2009, PMH-014-42)---- 2

3.5 SECTION 2: TIMER CONTROL..................................................................................................................... 36
3.6 SECTION 3: CONTROL REGISTER ............................................................................................................... 39
3.6.1 The control register.............................................................................................................................39
3.6.2 The status register...............................................................................................................................60
3.6.3 The A/D software trigger register .......................................................................................................61
3.7 SECTION 4: D/I/O REGISTER...................................................................................................................... 62
3.7.1 Digital Output/Digital Input................................................................................................................62
3.7.2 Card ID Register.................................................................................................................................63
3.8 SECTION 5: A/D &D/A REGISTER............................................................................................................. 64
4. A/D CONVERSION OPERATION ...............................................................................................................66
4.1 THE CONFIGURATION CODE TABLE .......................................................................................................... 66
4.2 THE UNIPOLAR/BIPOLAR........................................................................................................................... 67
4.3 THE INPUT SIGNAL RANGE........................................................................................................................ 67
4.4 THE SETTLING TIME .................................................................................................................................. 68
4.5 HOW TO DELAY THE SETTLING TIME ........................................................................................................ 68
4.6 THE AD CONVERSION MODE .................................................................................................................... 69
4.7 THE FIXED-CHANNEL MODE AD CONVERSION ......................................................................................... 71
4.8 THE MAGICSCAN MODE AD CONVERSION ............................................................................................... 72
4.8.1 The MagicScan Circular_Scan_Queue ...............................................................................................73
4.8.2 The Digital Filter of MagicScan..........................................................................................................74
4.8.3 The Different Sampling Rate of MagicScan ........................................................................................74
4.8.4 The High/Low Alarm of MagicScan....................................................................................................75
4.8.5 The MagicScan Function.....................................................................................................................76
4.8.6 The MagicScan Thread........................................................................................................................78
5. M_FUNCTION ................................................................................................................................................81
5.1 INTRODUCTION.......................................................................................................................................... 82
6. CONTINUOUS CAPTURE FUNCTIONS....................................................................................................86
6.1 GENERAL PURPOSE DRIVER ...................................................................................................................... 86
6.2 SAVE DATA IN PC MEMORY DRIVER ........................................................................................................ 90
7. CALIBRATION...............................................................................................................................................92
7.1 AD CALIBRATION ..................................................................................................................................... 92
7.2 D/A CALIBRATION .................................................................................................................................... 94
8. SOFTWARE AND DEMO PROGRAM........................................................................................................96
9. DIAGNOSTIC PROGRAM............................................................................................................................98
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver. 4.2, Dec/2009, PMH-014-42)---- 3

9.1 POWER-ON PLUG&PLAY TEST .................................................................................................................. 98
9.2 DRIVER PLUG&PLAY TEST ....................................................................................................................... 98
9.3 D/O TEST .................................................................................................................................................. 99
9.4 D/A TEST .................................................................................................................................................. 99
9.5 A/D TEST .................................................................................................................................................. 99
10. PERFORMANCE EVALUATION............................................................................................................ 100
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver.4.2, Dec/2009, PMH-014-42)---- 4

1. Introduction
1.1 General Description
The PCI-1800(H/L) and PCI-1802(H/L) are high performance, multifunction analog, digital
I/O board for PC and compatible computers in a 5 V PCI slot. This series features a continuous,
330 k Samples/Sec., gap-free data acquisition under DOS, Windows 95/98 and Windows NT
3.51/4.0. This family has the same features: one 12-bit 330 k AD converter, two 12-bit
independent DA converter, 16 channels TTL compatible DI and 16 channels TTL compatible
DO. The 1800H/L provides 16 channels single-ended or 8 channel differential inputs. The
1802H/L provides 32 channels single-ended or 16 differential inputs. The letter ｀L＇denotes
the low gain and the ｀H＇denotes the high gain. Two DACs of this multifunction card are
independent bipolar voltage output with jumper selectable voltage output range. The AD scan
function of 1800 series is very amazing; we call it “MagicScan＂. It scans with two modes:
the fix channel mode and the channel scan mode, both modes can be up to 330 k samples per
second. We also provide three trigger modes for this series: software trigger, pacer trigger and
external trigger; each trigger mode uses “MagicScan＂to perform the data acquisition. The
external trigger can be programmed to one of the three trigger methods : pre-trigger, post-
trigger and middle-trigger. The PCI-1800/1802 fully supports “Plug and Play ＂under
Windows 95/98/2000/XP.
The PCI-1202HU/LU,PCI-1602U/FU are new version of PCI-1202H/L and PCI-1602
they can be installed in 3.3 V, 5 V or 3.3 V/5 V Universal PCI-Bus. The PCI-1202H/L and
PCI-1602/1602F could be replaced with PCI-1202HU/LU and PCI-1602U/1602FU without
modifying software.
The PCI-1202(H/L/HU/LU) is very similar to PCI-1802(H/L). The different items between the
PCI-1802 and PCI-1202 are given as follows:
*A/D sampling rate is 110 k Samples/Sec.for PCI-1202(L/LU)
*FIFO size is 1 k samples
The PCI-1602/PCI-1602U(FU) is very similar to PCI-1802L. The different items between
the PCI-1802 and PCI-1602 are given as follows:
*A/D is 16-bit
*A/D sampling rate is 200 k Samples/Sec.for PCI-1602F/FU
*A/D sampling rate is 100 k Samples/Sec.for PCI-1602(U)
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver. 4.2, Dec/2009, PMH-014-42)---- 5

1.2 The Block Diagrams
The block diagram of PCI-1202/1602/1800/1802 is given as follows:
Analog Output
X86 System
PCI BUS
PCI Interface System EPROM
Local System Controller Status
Control
16 bits DI
16 bits DO
2 channels
12 bit DA
Converter
FIFO
2/8K
Analog Input
Digital Output
Digital Input
DAC OUT 0
DAC OUT 1
Magic Scan Controller
12/16bit A/D
Converter Mu
x
Gain
Figure 1-1 The block diagram of PCI-1202/1602/1800/1802
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver.4.2, Dec/2009, PMH-014-42)---- 6

1.3 Features
The general features of PCI-1202/1602/1800/1802 series are given as follows:
*Bus: 5 V PCI ( Peripherals Component Interface) bus for PCI-1202/1602/180x H/L
*Universal PCI card, supports both 5 V and 3.3 V PCI bus for PCI-1202HU/LU,1602U/FU
*A/D:
1. PCI-1800(L)/1802(L) : A/D converter = 330 k Samples/Sec.
PCI-1800(H)/1802(H) : A/D converter = 44 k Samples/Sec.
PCI-1602(F/FU): A/D converter = 200 k Samples/Sec.
PCI-1602(U): A/D converter = 100 k Samples/Sec.
PCI-1202(L/LU): A/D converter = 110 k Samples/Sec.
PCI-1202(H/HU): A/D converter = 44 k Samples/Sec.
2. 32 single-ended / 16 differential analog inputs for PCI-1202/1602/1802 H/L/HU/LU.
3. Three different A/D triggers: software, pacer and external trigger
. 4. Provides three different external triggers: pre-trigger, middle-trigger and post-trigger
5. Programmable input signal configuration.
6. Provides “MagicScan” function
7. FIFO(sample): 1 k for PCI-1202(H/L/HU/LU)/1800(H/L)
8 k for PCI-1802(H/L)
8 k for PCI-1602, PCI-1602F,PCI-1602U/FU and PCI-1802(H/L)
*D/A:
1. Two channels independent 12 bits DACs.
2. Bipolar voltage output with +/-5 V or +/- 10 V jumper selectable.
3. High throughput: refer to chapter 10.
*DIO:
1. 16 channels TTL compatible DI and 16 channels TTL compatible DO.
2. High speed data transfer rate: refer to chapter 10.
*Timer:
Three 16-bit independent timer
1. Timer 0 is used as the internal A/D pacer trigger timer.
2. Timer 1 is used as the external trigger A/D pacer timer.
3. Timer 2 is used as the machine independent timer.
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver. 4.2, Dec/2009, PMH-014-42)---- 7

1.4 Specifications
1.4.1 PCI-1202L/H/LU/HU
Model Name PCI-1202 L PCI-1202 H PCI-1202 LU PCI-1202 HU
Analog Input
Channels 32 single-ended / 16 differential
A/D Converter 12-bit, 8.5 µs conversion time
Sampling Rate 110 kS/s. max.
FIFO Size 1024 samples
Over voltage Protection Continuous +/-35 Vp-p
Input Impedance 10 MΩ/6 pF
Trigger Modes Software, Internal programmable pacer, External (5 V/TTL compatible)
Data Transfer Polling
Accuracy 0.01 % of FSR ±1 LSB @ 25 °C, ± 10 V
Zero Drift +/- 4 ppm/°C of FSR
Analog Output
Channels 2
Resolution 12-bit
Accuracy 0.06% of FSR ± 1 LSB @ 25 °C, ± 10 V
Output Range Bipolar:+/5 V, +/-10 V
Output Driving +/- 5 mA
Slew Rate 8.33 V/µs
Output Impedance 0.1 Ωmax.
Operating Mode Software
Digital Input
Channels 16
Compatibility 5 V/TTL
Input Voltage Logic 0: 0.8 V max. / Logic 1: 2.0 V min.
Response Speed 2.7 MHz (Typical)
Digital Output
Channels 16
Compatibility 5 V/TTL
Output Voltage Logic 0: 0.4 V max. / Logic 1: 2.4 V min.
Output Capability Sink: 2.4 mA @ 0.8 V / Source: 0.8 mA @ 2.0 V
Response Speed 2.7 MHz (Typical)
Timer/Counter
Channels 3(Independent x 1/Internal pacer x 1/External pacer x 1)
Resolution 16-bit
Compatibility 5 V/TTL
Input Frequency 10 MHz max.
Reference Clock Internal: 8 MHz
General
Bus Type 5 V PCI, 32-bit, 33 MHz 3.3 V/ 5 V Universal PCI, 32-bit, 33 MHz
Data Bus 16-bit
Card ID No Yes(4-bit) for Version 4.0 or above
I/O Connector Female DB37 x 1 / Male 20-bit ribbon x 2
Dimensions (L x W) 205 mm x 105 mm
Power Consumption 300 mA @ +5 V
Operating Temperature 0 ~ 60 °C
Storage Temperature -20 ~ 70 °C
Humidity 5 ~ 85% RH, non-condensing
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver.4.2, Dec/2009, PMH-014-42)---- 8

1.4.2 PCI-1602/1602F
Model Name PCI-1602 PCI-1602U PCI-1602 F PCI-1602 FU
Analog Input
Channels 32 single-ended / 16 differential
AD Converter 16-bit, 2 µs conversion time
Sampling Rate 100 kS/s. max. 200 kS/s. max.
FIFO Size 8192 samples
Over voltage Protection Continuous +/-35 Vp-p
Input Impedance 10 MΩ/6 pF
Trigger Modes Software, Internal programmable pacer, External (5 V/TTL compatible)
Data Transfer Polling
Accuracy 0.01 % of FSR ±1 LSB @ 25 °C, ± 10 V
Zero Drift +/- 2 ppm/°C of FSR
Analog Output
Channels 2
Resolution 12-bit
Accuracy 0.06% of FSR ± 1 LSB @ 25 °C, ± 10 V
Output Range Bipolar:+/5 V, +/-10 V
Output Driving +/- 5 mA
Slew Rate 8.33 V/µs
Output Impedance 0.1 Ωmax.
Operating Mode Software
Digital Input
Channels 16
Compatibility 5 V/TTL
Input Voltage Logic 0: 0.8 V max.
Logic 1: 2.0 V min.
Response Speed 3.0 MHz (Typical)
Digital Output
Channels 16
Compatibility 5 V/TTL
Output Voltage Logic 0: 0.4 V max.
Logic 1: 2.4 V min.
Output Capability Sink: 2.4 mA @ 0.8 V
Source: 0.8 mA @ 2.0 V
Response Speed 3.0 MHz (Typical)
Timer/Counter
Channels 3(Independent x 1/Internal pacer x 1/External pacer x 1)
Resolution 16-bit
Compatibility 5 V/TTL
Input Frequency 10 MHz max.
Reference Clock Internal: 8 MHz
General
Bus Type 5 V PCI, 32-
bit, 33 MHz
3.3 V/ 5 V Universal
PCI, 32-bit, 33 MHz
5 V PCI, 32-
bit, 33 MHz
3.3 V/ 5 V Universal
PCI, 32-bit, 33 MHz
Data Bus 16-bit
Card ID No Yes(4-bit) No Yes(4-bit)
I/O Connector Female DB37 x 1 / Male 20-bit ribbon x 2
Dimensions (L x W) 205 mm x 105 mm
Power Consumption 350 mA @ +5 V
Operating Temperature 0 ~ 60 °C
Storage Temperature -20 ~ 70 °C
Humidity 5 ~ 85% RH, non-condensing
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver. 4.2, Dec/2009, PMH-014-42)---- 9

1.4.3 PCI-1800/1802
Model Name PCI-1802 H/L PCI-1800 H/L
Analog Input
Channels 32 single-ended / 16 differential 16 single-ended / 8 differential
AD Converter 12-bit, 3 µs conversion time
Sampling Rate 330 kS/s. max.
FIFO Size 8192 samples 1024 samples
Over voltage Protection Continuous +/-35 Vp-p
Input Impedance 10 MΩ/6 pF
Trigger Modes Software, Internal programmable pacer, External (5 V/TTL compatible)
Data Transfer Polling
Accuracy 0.01 % of FSR ±1 LSB @ 25 °C, ± 10 V
Zero Drift +/- 2 ppm/°C of FSR
Analog Output
Channels 2
Resolution 12-bit
Accuracy 0.06% of FSR ± 1 LSB @ 25 °C, ± 10 V
Output Range Bipolar:+/5 V, +/-10 V
Output Driving +/- 5 mA
Slew Rate 8.33 V/µs
Output Impedance 0.1 Ωmax.
Operating Mode Software
Digital Input
Channels 16
Compatibility 5 V/TTL
Input Voltage Logic 0: 0.8 V max.
Logic 1: 2.0 V min.
Response Speed 3.0 MHz (Typical)
Digital Output
Channels 16
Compatibility 5 V/TTL
Output Voltage Logic 0: 0.4 V max.
Logic 1: 2.4 V min.
Output Capability Sink: 2.4 mA @ 0.8 V
Source: 0.8 mA @ 2.0 V
Response Speed 3.0 MHz (Typical)
Timer/Counter
Channels 3(Independent x 1/Internal pacer x 1/External pacer x 1)
Resolution 16-bit
Compatibility 5 V/TTL
Input Frequency 10 MHz max.
Reference Clock Internal: 8 MHz
General
Bus Type 5 V PCI, 32-bit, 33 MHz
Data Bus 16-bit
Card ID No
I/O Connector Female DB37 x 1
Male 20-bit ribbon x 2
Dimensions (L x W) 200 mm x 105 mm
Power Consumption 300 mA @ +5 V
Operating Temperature 0 ~ 60 °C
Storage Temperature -20 ~ 70 °C
Humidity 5 ~ 85% RH, non-condensing
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver.4.2, Dec/2009, PMH-014-42)---- 10

1.4.4 Analog Input Range
Model PCI-1202 L /PCI-1202 LU (Low-Gain)
Gain 0.5 1 2 4 8
Unipolar(V) +/- 10 +/- 5 +/- 2.5 +/- 1.25 +/- 0.625
Bipolar(V) - 0 ~ 10 0 ~ 5 0 ~ 2.5 0 ~ 1.25
Sampling
Rate Max. 110 kS/s
Model PCI-1202 H / PCI-1202 HU (High-Gain)
Gain 0.5 1 5 10 50 100 500 1000
Unipolar(V) +/- 10 +/- 5 +/- 1 +/- 0.5 +/- 0.1 +/- 0.05 +/- 0.01 +/- 0.005
Bipolar(V) - 0 ~ 10 - 0 ~ 1 - 0 ~ 0.1 - 0 ~ 0.01
Sampling
Rate Max. 44 kS/s 10 kS/s 1 kS/s
Model PCI-1602/1602U
Gain 1 2 4 8
Bipolar(V) +/- 10 +/- 5 +/- 2.5 +/- 1.25
Sampling
Rate Max. 100 kS/s
Model PCI-1602F/1602FU
Gain 1 2 4 8
Bipolar(V) +/- 10 +/- 5 +/- 2.5 +/- 1.25
Sampling
Rate Max. 200 kS/s
Model PCI-1800 L /PCI-1802 L (Low-Gain)
Gain 0.5 1 2 4 8
Unipolar(V) +/- 10 +/- 5 +/- 2.5 +/- 1.25 +/- 0.625
Bipolar(V) - 0 ~ 10 0 ~ 5 0 ~ 2.5 0 ~ 1.25
Sampling
Rate Max. 330 kS/s
Model PCI-1800 H / PCI-1802 H (High-Gain)
Gain 0.5 1 5 10 50 100 500 1000
Unipolar(V) +/- 10 +/- 5 +/- 1 +/- 0.5 +/- 0.1 +/- 0.05 +/- 0.01 +/- 0.005
Bipolar(V) - 0 ~ 10 - 0 ~ 1 - 0 ~ 0.1 - 0 ~ 0.01
Sampling
Rate Max. 44 kS/s 10 kS/s 1 kS/s
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver. 4.2, Dec/2009, PMH-014-42)---- 11

z12-bit ADC Input Voltages and Output Codes for PCI-1202/1800/1802 H/L/HU/LU
Analog Input Digital Output Binary Code Hex Code
+9.995 V
0 V
-4.88 mv
-10 V
MSB LSB
1111 1111 1111
1000 0000 0000
0111 1111 1111
0000 0000 0000
FFF
800
7FF
000
z16-bit ADC Input Voltages and Output Codes for PCI-1602 /F/U/FU
Analog Input Digital Output Binary Code Hex Code
+9.99 V
+0 V
-305 µV
-10 V
MSB LSB
0111 1111 1111 1111
0000 0000 0000 0000
1111 1111 1111 1111
1000 0000 0000 0000
7FFF
0000
FFFF
8000
z12- bit DAC output code for PCI-1202/1800/1802 H/L/HU/LU
Data Input Analog Output
MSB LSB
1111 1111 1111
1000 0000 0001
1000 0000 0000
0111 1111 1111
0000 0000 0000
+Vref (2047/2048)
+Vref (1/2048)
0 Volts
-Vref (1/2048)
-Vref (2048/2048)
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver.4.2, Dec/2009, PMH-014-42)---- 12

1.4.5 A/D Trigger Methods
zTrigger modes:
1. Internal software trigger
2. Internal pacer trigger
3. External trigger: pre-trigger, middle-trigger and post-trigger
External trigger
Figure 1-2 Trigger modes of PCI-1202/1602/1800/1802
CHn
External trigger
End
Start
External middle-
t
N2
t
Start
End
External post-trigger
CHn
External trigger
Start
End
CHn
External pre-
t
t
Start
E
nd
Internal pacer trigger
CHn
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver. 4.2, Dec/2009, PMH-014-42)---- 13

1.5 Applications
zSignal analysis.
zFFT & frequency analysis.
zTransient analysis.
zSpeech analysis.
zTemperature monitor.
zProduction test.
zProcess control.
zVibration analysis.
zEnergy management.
zOther industrial and laboratory measurement and control.
1.6 Product Check List
Your package includes the following items:
zOne PCI-1202/1602/1800/1802 H/L/HU/LU multifunction card.
zOne company CD
zOne Quick Start Guide
It is recommended to read the Quick Start Guide first. All the necessary and essential
information are given in the Quick Start Guide as follows:
1. Where to get the software driver, demo programs and other resources.
2. How to install software driver.
3. How to test the card.
Attention!
If any of these items are missing or damaged, please contact your local field agent.
Save the shipping materials and carton in case you want to ship or store the product
in the future.
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver.4.2, Dec/2009, PMH-014-42)---- 14

2. Hardware Configuration
2.1 Board Layout
Figure 2-1 PCI-180X(H/L)/NDA board layout
OUT
CON1 CON2
PCI-1800/1802L/NDA REV:C
IN
CON3
VR1 VR101 VR2 VR3VR100
J1
10V
5V
ADC input 16 or 32 channels External Trigger Input
Digital Input 16 channels
Digital Output 16 channels
JP1 1 2 5 6
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver. 4.2, Dec/2009, PMH-014-42)---- 15

Figure 2-2 PCI-1202(H/L)/1800(H/L)/1802(H/L) board layout
OUT
CON1 CON2
PCI-1800/1802L REV:F
IN
CON3
VR1 VR101 VR2
VR200VR100
J1
10V
5V
DAC output 2 channels ADC input 16 or 32 channels External Trigger Input
Digital Input 16 channels
Digital Output 16 channels
JP1 1 2 5 6
VR201 VR202 VR203
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver.4.2, Dec/2009, PMH-014-42)---- 16

Figure 2-3. PCI-1202(HU/LU) board layout
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver. 4.2, Dec/2009, PMH-014-42)---- 17

Figure 2-4 PCI-1602/1602F board layout
OUT
CON1 CON2
PCI-1602/1602F REV:1.0
IN
CON3
VR1 VR3
VR2 VR4
J1
10V
5V
DAC output 2 channels ADC input 32 channels External Trigger Input
Digital Input 16 channels
Digital Output 16 channels
JP1
2 6
VR5 VR6 VR7
1
5
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver.4.2, Dec/2009, PMH-014-42)---- 18

SW1
1 2 3 4
OUT
CON1 CON2
IN
CON3
VR1 VR3
VR2 VR4 J1
10V
5V
DAC output 2 channels ADC input 32 channels External Trigger Input
Digital Input 16 channels
Digital Output 16 channels
JP1 2
6
VR5 VR6 VR7
1
5
JP4
PCI-1602U/1602FU
Figure 2-4 PCI-1602U/1602FU board layout
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver. 4.2, Dec/2009, PMH-014-42)---- 19

2.2 Jumper Setting
2.2.1 JP1 : A/D Input Type Selection
This jumper is used to select the analog input type. For single-ended inputs,
the use should connect pin1, 3 and pin2, 4. For differential inputs, pin3, 5 and pin4,
6 should be connected.
2.2.2 J1 : D/A Reference Voltage Selection
J1 is used to select the internal D/A output reference voltage. To select the
±10 V voltage output, the pin 1&2 should be connected. To select the ±5 V voltage
output, the pin 2&3 should be connected.
2.2.3 D/I Port Setting (PCI-1202HU/LU/1602U/1602FU only)
This DI ports can be pull-high or pull-low selected by JP2. The location is
given as following:
JP1
Differential
In
p
uts
6
2
1
5
J1
1
10 Voltage
default)
±
output (
J1
1
±5 Voltage
output
JP1
1
5
2
6
Single-Ended
In
p
uts
(
default
)
3
2
1
Pull Low
3
2
1
Pull High
JP2
JP2
PCI-1202/1602/1800/1802 Hardware User’s Manual (Ver.4.2, Dec/2009, PMH-014-42)---- 20