ICP DAS USA PCI-D96SU User manual

Technical support: servic[email protected] P1
PCI-D96SU/D128SU
Quick Start
v1.0, Apr. 2019
What’s in the box?
Related Information
The package includes the following items:
PCI-D96SU/D128SU x 1
Quick Start x 1
(This Document)

For more detailed information related to the user manual and
software for UniDAQ Driver & SDK:
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
For more detailed information related to the hardware settings for
PCI-D96SU/D128SU Card:

DN-100 and CA-SCSI100-15 Product Page (optional):
PCI-D96SU
PCI-D128SU
or

Technical support: servic[email protected] P2
1 Appearance
2 Jumper Settings
DI Pull-high/low Jumper
Jumpers JP3 to JP6 are used to specify whether the Digital Input is
either Pull-high or Pull-low. NOTE: Ensure that Jumpers JP3 to JP6
are in the default position before performing a self-test.
Pull-Low (Default)
Pull- High
JP5
PC
HI L0
JP3
PA
HI L0JP4
PB
HI L0
JP6
PD
HI L0
1 2 3 4
SW1
JP1JP2


CN2: PD Port
CN1: PD Port

CON1:
PA/PB/PC
Port

DI Pull-high/low Jumper

Card ID Switch

DIO Operating Voltage
Jumper
132
HI LO
132
HI LO

Technical support: servic[email protected] P3
DIO Operating Voltage Jumper
Jumpers JP1 and JP2 are used to specify the DIO operating voltage
levels. NOTE: Ensure that Jumpers JP1 and JP2 are in the default
position before performing a self-test.
1
3
2
P1
1
3
2
1
3
2
P2 P3
JP1
1
3
2
JP2
JP1
JP2
Voltage
P1
P2
P3
2-3
1-2
1-2
2-3
+1.5 V
1-2
2-3
1-2
2-3
+1.8 V
1-2
1-2
1-2
2-3
+2.5 V
1-2
1-2
2-3
2-3
+3.3 V
X
X
X
1-2
+5.0 V (Default)
3 Installing Hardware on PC
1) Shut down and power off your Computer.
2) Remove all covers from the Computer.
3) Select an unused PCI slot.
4) Carefully insert the PCI-D96SU/D128SU
Card into PCI slot.
4) Replace the Computer Covers.
5) Power on the Computer.

Technical support: servic[email protected] P4
4 Installing Windows Driver
1) Setup the UniDAQ driver under Windows 10.
The UniDAQ driver supports 32-/64-bit Windows XP/2003/2008/7/8/10
which can be found in the
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/.
2) Setup the UniDAQ Driver DLL, click the “Next>”button for all dialogs.
NOTE: For more detailed information related to driver installation,
refer to Chapter 2 “Starting” in the UniDAQ SDK user manual.
3) The operating system will automatically detect the new hardware and
install the necessary drivers after reboot the PC.
4) Open the “Device Manager” to verify that the PCI-D96SU/D128SU
Card has been correctly installed and is in the Device Manager, as
illustrated on below.

Technical support: servic[email protected] P5
5 Pin Assignments

Technical support: servic[email protected] P6
6 Self-test Wiring
1) Verify that Jumpers DI Pull-high/low (JP3 ~ JP6) on the
PCI-D96SU/D128SU are set to the “Pull-Low (default)”position.
NOTE: Refer to Chapter 2 “Jumper Settings”above (P2).
2) Connect the DN-100 terminal board (optional) to the CON1 on the
PCI-D96SU/D128SU Card using the CA-SCSI100-15 cable (optional).
3) Connect the Port0 (PA00~PA07) with Port1 (PB00~PB07).

Technical support: servic[email protected] P7
7 Execute the Test Program
1) Launch the UniDAQ Utility software.
If the UniDAQ Utility was installed in the default folder, it will be located
at “C:\ICPDAS\UniDAQ\Driver”.
2) Confirm that the PCI-D96SU/D128SU Card has been successfully
installed in the Host system.
NOTE: The device numbers
start from 0.
3) Click the “TEST”button to start
the test.
Double-click



Technical support: servic[email protected] P8
3) Click the “Digital Output”tab.
4) Select “Port0”from the “Port Number”drop-down options.
5) Click the DO channels 0, 2, 4 and 6 buttons.
6) Click the “Digital Input”tab.
7) Select “Port1”from the “Port Number”drop-down options.
8) The DI indicators will turn red when the corresponding DO channels
0, 2, 4 and 6 are ON.





