ICP DAS USA PCIe-S114 User manual

Copyright © 2021 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail] Page: 1
Q
Qu ui ic ck k S St ta ar rt t
June 2021/ Version 1.0
f
fo or r P PC CI Ie e- -S S1 11 14 4( (i i) )
P
PC CI Ie e- -S S1 14 44 4( (i i) )
I
In ns st ta al ll li in ng g W Wi in nd do ow ws s
D
Dr ri iv ve er r
Launch the Windows XP/7/8/10/2012/
2016 (32/64-bit) driver setup program
(PCIe_SPCard_Win_Setup_1.00.02.exe),
which can be obtained from either the
companion CD-ROM or the web site:
CD: \Napdos\multiport\windows\
https://www.icpdas.com/en/download/index.php?
nation=US&kw=PCIe+Series+Card+Windows+Driver
Click the “Next>” button to start the installation.
Click the “Next>” button to install the driver into the default folder.
In the installation process, the Command Prompt windows will be displayed, don't care.
And please do not close this Command Prompt window in installation process.
Select the “NO, I will restart the computer later” and click the “Finish” button.
2
2
2
W
Wh ha at t’ ’s s i in n t th he e
S
Sh hi ip pp pi in ng g P Pa ac ck ka ag ge e? ?
The package includes the following
items:
PCIe-S114 or PCIe-S144
Quick Start Guide (This Guide)
Software CD (V6.1 or later)
CA-4002 D-Sub Connector
1
1
1

Copyright © 2021 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected] Page: 2
I
In ns st ta al ll li in ng g t th he e H Ha ar rd dw wa ar re e
Shut down and power off your computer.
Remove the cover from the computer.
Select an unused PCI Express slot.
Carefully insert your PCIe-S1x4 card into the PCI Express slot.
Replace the PC cover.
Power on the computer.
Follow the prompt message to finish the Plug & Play steps.
Please open the “Device Manager” to verify the COM port installation, as follows steps:
8-1: In Windows 7, Click “Start”button, and then click “Control Panel”.
8-2: Click “System and Maintenance”, and then click “Device Manager”.
8-3: Verify that the COM ports of PCIe-S114/S144 card are listed correctly.
3
3
3
Successful Installation
COM port mapping is automatically
applied depending on the PC.
Successful Installation
Check whether the PCIe-S1x4 card
is listed correctly or not.

Copyright © 2021 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected] Page: 3
M Ma an nu ua al l C CO OM M P Po or rt t C Co on nf fi ig gu ur ra at ti io on n
If the auto-configuration for COM Port is messy or that is not you need, you can change the COM port
mappings. For detailed configuration steps, please refer to the following steps:
Open Windows Device Manager and right click the serial port of the PCIe-S1x4 series card.
Select the “Properties” item from the popup menu.
Click the “Port Settings”tab and click the “Advanced…” button.
Select the appropriate COM Port number from the “COM Port Number:”drop-down options and
click the “OK”button. Note that the COM port display “(in use)”means this COM port is being used.
Therefore, please do not select it.
Click the “OK”button in the “Properties” dialog box.
Restart your computer to complete the configuration.
4
4
4

Right Click





Copyright © 2021 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected] Page: 4
P
Pi in n A As ss si ig gn nm me en nt ts s a an nd d R RS S- -2 23 32 2 C Ca ab bl le e W Wi ir ri in ng g f fo or r
P
PC CI Ie e- -S S1 11 14 4( (i i) )
5
5
5
PCIe-S114/ PCIe-S114i DB-37
PCIe-S114/ PCIe-S114i DB-9
PCIe-S114 Card
RS-232 Wiring
Device
Signal
PIN
PIN
Signal
RxD
2
3
TxD
TxD
3
2
RxD
GND
5
5
GND
DTR
4
6
DSR
--
--
1
DCD
DCD
1
--
--
DSR
6
4
DTR
RTS
7
8
CTS
CTS
8
7
RTS
RI
9
9
RI

Copyright © 2021 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected] Page: 5
P
Pi in n A As ss si ig gn nm me en nt ts s a an nd d R RS S- -4 42 22 2/ /4 48 85 5 C Ca ab bl le e W Wi ir ri in ng g
f
fo or r P PC CI Ie e- -S S1 14 44 4( (i i) )
PCIe-S144 Card
RS-422 Wiring
Device
Signal
PIN
PIN
Signal
TxD-
1
4
RXD-
TxD+
2
3
RxD+
RxD+
3
2
TxD+
RxD-
4
1
TxD-
GND
5
5
GND
RTS-
6
9
CTS-
RTS+
7
8
CTS+
CTS+
8
7
RTS+
CTS-
9
6
RTS-
PCIe-S144 Card
RS-485 Wiring
Device
Signal
PIN
PIN
Signal
DATA-
1
1
DATA-
DATA+
2
2
DATA+
Note: The RS-485 bus is a differential (balanced) signal, thus you cannot wire the Data+ with
Data- directly for a single port loop-back test. It will not work at all.
6
6
6
PCIe-S144/ PCIe-S144i DB-37
PCIe-S144/ PCIe-S144i DB-9

Copyright © 2021 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected] Page: 6
S Se el lf f- -T Te es st t W Wi ir ri in ng g
Step 1: Connect the DN-37 terminal board (optional) to the PCIe-S1x4 series card
using the CA-3710 cables (optional).
Step 2: Wire the Port 3 and Port4.
PCIe-S114(i) card (RS-232 Wiring): Shorting the RxD, TxD and GND pins of both Port3 and Port4.
PCIe-S144(i) card (RS-485 Wiring):
Shorting the Port3 Data+ and Port4 Data+ and the Port3 Data- and Port4 Data- pins.
7
7
7
Port3 Signal
PIN
PIN
Port4 Signal
RxD3
24
28
TxD4
TxD3
05
10
RxD4
Port3 Signal
PIN
PIN
Port4 Signal
Data3-
02
25
Data4-
Data3+
05
28
Data4+
DN-37
CA-3710
PCIe-S114(i)/PCIe-S144(i)

Copyright © 2021 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected] Page: 7
E Ex xe ec cu ut te e t th he e T Te es st t P Pr ro og gr ra am m
Step 1: Execute the Test2COM.exe program, which can be downloaded from:
Step 2: Set the appropriate COM Ports, Baud Rate and Data Format information to the values shown
in the image below.
8
8
8
CD:\Napdos\multiport\utility
https://www.icpdas.com/en/download/index.php?nation=US&kw=Test2COM
COM Ports: Enter COM3 (First), COM4 (Second).
Data Bits: Check “8”
Parity: Check “None”
Stop Bits: Check “1”
Baud Rates: Check values 9600 to 115200
Test Loops: Type “1”
Click “Start Test” to begin the test.








Copyright © 2021 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected] Page: 8
S Su uc cc ce es ss sf fu ul l T Te es st ti in ng g
Once the test is complete, verify the test results.
If the result indicates that the test was successful, the expanded COM Port is ready-to-use.
R
Re el la at te ed d I In nf fo or rm ma at ti io on n
PCIe-S114(i)/PCIe-S144(i) card product page:
https://www.icpdas.com/en/product/guide+Industrial__Communication+Serial__Communicatio
n+Multi-port__Serial__Board#793
DN-37 and CA-3710 product page (optional):
https://www.icpdas.com/en/product/DN-37
https://www.icpdas.com/en/product/CA-3710
Software and documentation:
CD: \Napdos\multiport\
https://www.icpdas.com/en/download/index.php?model=PCIe-S114
9
9
9
Success Test: 5
Failed Test: 0