ICP DAS USA PCI-FC16U series User manual

PCI-FC16U Quick Start Guide ICP DAS CO., LTD.
1
Website: http:// www.icpdas.com.tw E-Mail: [e-mail] , service.icp[email protected]m
The shipping package includes the following items:
For PCI-FC16U
Check the Supplied Items
English/Oct. 2015/Version 1.1
Software Utility CD
(V6.2 or later)
Quick Start Guide
(This Document)
PCI-FC16U
CA-4002 D-Sub
Connector

PCI-FC16U Quick Start Guide ICP DAS CO., LTD.
2
Website: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
The UniDAQ driver supports Windows 2000 and 32/64-bit versions of Windows
XP/2003/2008/7/8. The driver installation package for PCI-FC16U board can be
found on the companion CD-ROM, or can be obtained from the ICP DAS FTP web
site. The driver is located at:
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
To install the UniDAQ driver, follow the procedure described below.
Step 1: Double-click the UniDAQ_Win_Setupxxx.exe icon to begin the installation
process.
Step 2: When the “Welcome to the ICP DAS UniDAQ Driver Setup Wizard”screen
is displayed, click the “Next>” button to start the installation.
Step 3: On the “Information”screen, verify that the DAQ card is included in the
list of supported devices, then click the “Next>” button.
Step 4: On the “Select Destination Location”screen, click the “Next>” button to
install the software in the default folder, C:\ICPDAS\UniDAQ.
Step 5: On the “Select Components”screen, verify that the DAQ Card is in the list
of device, and then click the “Next>” button to continue.
Step 6: On the “Select Additional Tasks” screen, click the “Next>” button.
Step 7: On the “Download Information”screen, click the “Next>” button
Step 8: Once the installation has completed, click “No, I will restart my computer
later”, and then click the “Finish” button.
Note: For detailed information about the driver installation, refer to Chapter 2
“Install UniDAQ Driver DLL” of the UniDAQ SDK User Manual.
Installing the Windows Driver

PCI-FC16U Quick Start Guide ICP DAS CO., LTD.
3
Website: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Note: For more details regarding the Card ID and
Jumper settings, refer to the PCI-FC16U User
Manual.
Jumper JP1 is used to configure the Digital I/O direction mode. Please make sure
JP1 jumper set to “SW”position (short pins 2 and 3) before self-test, as follows:
JP1
Jumper Selectable (Default)
Software Programmable
DIO-S0
1
HW 32 SW
1SW 32
HW
Note that the DIO-S1 and DIO-S2 jumpers are not used when the DIO-S0 jumper is set to
“Software Program” Mode. Refer to PCI-FC16U User Manual for more detail
information.
Board Layout
Jumper JP1 Settings






1. CON3 Connector
(See Section 6 Pin Assignments)
2. CON1 Connector
(See Section 6 Pin Assignments)
3. CON2 Connector
(See Section 6 Pin Assignments)
4. SW1: Card ID Switch
(The default setting is 0x0.)
5. JP3: DI Pull-high/low Settings
(The default setting is pull-low.)
6. JP1: Digital I/O Mode Settings
(See Section 4 Jumper JP1 Settings)

PCI-FC16U Quick Start Guide ICP DAS CO., LTD.
4
Website: http:// www.icpdas.com.tw E-Mail: [email protected]om , [e-mail]
Step 1: Shut down and power off the computer.
Step 2: Remove all the covers from the computer.
Step 3: Select an unused PCI slot.
Step 4: Carefully insert the PCI-FC16U board into
the PCI slot and secure the board in place.
Step 5: Replace the covers on the computer.
Step 6: Reconnect the power supply and power on
the computer.
Step 7: Once the computer reboots, follow any messages that may be displayed
to complete the Plug and Play installation procedure.
Step 8: Open the “Device Manager” in the Control Panel and verify that the
PCI-FC16U board is listed correctly, as illustrated below.
Installing the Hardware
Installation successful

PCI-FC16U Quick Start Guide ICP DAS CO., LTD.
5
Website: http:// www.icpdas.com.tw E-Mail: [email protected]om , [e-mail]
Pin Assignments

PCI-FC16U Quick Start Guide ICP DAS CO., LTD.
6
Website: http:// www.icpdas.com.tw E-Mail: [email protected]om , [e-mail]
Wiring for the Digital Input/Output Test:
Step 1: Keep set the JP1 jumper to “SW”position (See Section 4 Jumper
Settings).
Step 2: Connect the CON1 to CON2 on the PCI-FC16U board using the CA-2002
cable (optional).
Execute the UniDAQ Utility
Program:
Step 3: In Windows 7, click the
“Start” button, point to “All
Programs”,and then click the
“ICPDAS”folder. Point to “UniDAQ
Development Kits”and then click the
“UniDAQ Utility”to execute the
UniDAQ Utility Program.
Self-Test
CA-2002 Cable

PCI-FC16U Quick Start Guide ICP DAS CO., LTD.
7
Website: http:// www.icpdas.com.tw E-Mail: [email protected]om , [e-mail]
Step 4: Confirm that the PCI-FC16U board has
been successfully installed in the Host system.
Note that the device numbers start from 0.
Step 5: Click the “TEST”button to start the
test.
Step 6: Check the results of the Digital Input/Output functions test.
1. Click the “Digital Output”tab.
2. Select “Port0”from the “Port Number”drop-down menu.
3. Check the checkboxes for channels 0, 2, 4 and 6.




PCI-FC16U Quick Start Guide ICP DAS CO., LTD.
8
Website: http:// www.icpdas.com.tw E-Mail: [email protected]om , [e-mail]
4. Click the “Digital Input”tab.
5. Select “Port1”from the “Port Number”drop-down menu.
6. The DI indicators will turn red when the corresponding DO channels 0, 2,
4 and 6 are ON.
PCI-FC16U Series Board Product Page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/pci-fc16u.
html
CA-2002 Product Pages (optional):
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
UniDAQ Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
Related Information


