ICP DAS USA PIO-D24U User manual

- 1 -
Language English
Version V1.0
Update Apr.2009
………………………………………………
What’s in your package?
¾One PIO-D24U/PIO-D56U card
¾One companion PCI CD (V3.5 or later)
¾One Quick Start Guide (This document)
………………………………………………
Installing Windows Driver
Follow these steps:
1. Set up the Windows driver.
The driver is location at:
CD:\NAPDOS\PCI\PIO-DIO\dll_ocx\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pio-dio/dll_ocx/driver/
1
2
PIO-D24U
/
PIO-D56U

- 2 -
2. Click the button to start the installation.
3. Click the button to install the driver into the
default folder.
4. Click the button to continue the installation.
5. Select the “NO, I will restart my computer later”
and then click the button.
………………………………………………
Installing Hardware on PC
Follow these steps:
1. Shut down and power off your computer.
2. Remove the cover from the computer.
3. Select an unused PCI slot.
4. Carefully insert your I/O card into the PCI slot.
5. Replace the PC cover.
6. Power on the computer.
After powering-on the computer, please finished the
Plug&Play steps according to the prompt message.
3
The Windows driver only supports Windows 98/NT/2000
and XP/2003/Vista 32-bit versions.

- 3 -
………………………………………………
Pin Assignments
4
CN1:20-pin connector
(PIO-D56U only)
CN2:20-pin connector
(PIO-D56U only)
CN3: 37-pin connector
TTL High(1) 2.4 V ~ 5.0 V(Voltages over 5.0 V will damage the device)
None Defined 2.4 V ~ 0.8 V
TTL Low(0) Under 0.8 V
All signals are TTL compatible
Pin Description Pin Description
1 N.C. 20 VCC
2 N.C 21 GND
3 P1B7 22 P2C7
4 P1B6 23 P2C6
5 P1B5 24 P2C5
6 P1B4 25 P2C4
7 P1B3 26 P2C3
8 P1B2 27 P2C2
9 P1B1 28 P2C1
10 P1B0 29 P2C0
11 GND 30 P0A7
12 N.C. 31 P0A6
13 GND 32 P0A5
14 N.C 33 P0A4
15 GND 34 P0A3
16 N.C 35 P0A2
17 GND 36 P0A1
18 VCC 37 P0A0
19 GND
Pin Description Pin Description
1 DO0 2 DO1
3 DO2 4 DO3
5 DO4 6 DO5
7 DO6 8 DO7
9 DO8 10 DO9
11 DO10 12 DO11
13 DO12 14 DO13
15 DO14 16 DO17
17 GND 18 GND
19 VCC 20 +12 V
Pin Description Pin Description
1 DI0 2 DI1
3 DI2 4 DI3
5 DI4 6 DI5
7 DI6 8 DI7
9 DI8 10 DI9
11 DI10 12 DI11
13 DI12 14 DI13
15 DI14 16 DI17
17 GND 18 GND
19 VCC 20 +12 V

- 4 -
………………………………………………
Self Test
1. Use the DN-37(Optional) to connect Port 0 to
Port 1.
2. Execute the DIO sample program.
The sample program is contained in a zip file which
is located at: CD:\NAPDOS\PCI\PIO-DIO\dll_ocx\Demo
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pio-dio/dll_ocx/demo/
5
DN-37 DIO Wiring
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
CN2
(PIO-D56U only)
CN1
(PIO-D56U only)
CN3
CA-3710

- 5 -
3. Check the board number of the PIO-D24U/
PIO-D56U, and test the DIO functions.
4. Get DIO function test result.
1. One PIO-D24U
/
D56U card has been
successfully installed
in PC.
2. Select the board
number for the
PIO-D24U/D56U.
It starts from 0.
3. Click the test
button to run the
DIO functions test.
Complete
Output Port 0 (HEX) = X
Input Port 2,1 (HEX) = FF Y
X = Y => Pass!!!
Example,
Output Port 0 (HEX) = 80
Input Port 2,1 (HEX) = FF 80
X=Y=80 =>Pass

- 6 -
………………………………………………
Additional Information
9PIO-D24U/PIO-D56U Card Product page:
http://www.icpdas.com/products/DAQ/pc_based/pio_d56_24.htm
9DN-37(Optional) page:
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
9Documentation:
CD:\NAPDOS\PCI\PIO-DIO\manual
CD:\NAPDOS\PCI\Manual
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pio-dio/manual/
9Software:
CD:\NAPDOS\PCI\PIO-DIO\
http://www.icpdas.com/download/pci/piodio/index.htm
The ICP DAS Web Site
http://www.icpdas.com
Contact Us
[email protected]
Copyright ©2009 by ICP DAS Co., Ltd. All rights are reserved
6
Technical support
Supplies and ordering information
Methods of enhancing your device
FAQ
Application examples