IDS 816 User guide

IDS 816 700-283-02IIssuedSeptember2009
2

IDS 816 700-283-02IIssuedSeptember2009
3
Contents
1. Introduction to the IDS 816 ----------------------------------------------------------------------------- 8
1.1 Features of the IDS 816--------------------------------------------------------------------------------------8
2. Installation and Wiring ----------------------------------------------------------------------------------- 9
2.1 Additional Technical Data --------------------------------------------------------------------------------- 10
2.2 End-of-Line Resistors--------------------------------------------------------------------------------------- 10
2.3 Box Tamper Input ------------------------------------------------------------------------------------------- 12
2.4 Installing an Expander Module --------------------------------------------------------------------------- 12
2.5 Connecting the Telephone Communicator------------------------------------------------------------ 12
2.6 Programmable Outputs------------------------------------------------------------------------------------ 12
2.7 Key-switch or Remote Control Unit---------------------------------------------------------------------- 12
2.8 IDS Remote Receiver--------------------------------------------------------------------------------------- 13
2.9 Radio Transmitter Connection---------------------------------------------------------------------------- 13
3. Hardware Reset Switch ---------------------------------------------------------------------------------13
4. Enrolling Keypads and Other Devices-------------------------------------------------------------13
4.1 Replacing a Faulty Keypad/Device---------------------------------------------------------------------- 14
4.2 Defaulting Keypads ----------------------------------------------------------------------------------------- 14
5. Event Log ---------------------------------------------------------------------------------------15
6. Download Code ---------------------------------------------------------------------------------------15
6.1 Programming the Panel------------------------------------------------------------------------------------ 15
6.2 Location Values---------------------------------------------------------------------------------------------- 15
7. Programming the Panel---------------------------------------------------------------------------------16
7.1 Entering Program Mode ----------------------------------------------------------------------------------- 17
7.2 Programming Standard Locations ---------------------------------------------------------------------- 17
7.3 Programming Extended Locations ---------------------------------------------------------------------- 17
7.4 Programming a Bitmapped Location ------------------------------------------------------------------- 18
7.5 Incorrect Data Entries -------------------------------------------------------------------------------------- 18
7.6 Programming Location Summary ----------------------------------------------------------------------- 18
7.6.1 Zone Options------------------------------------------------------------------------------------------------- 19
7.6.2 System Options---------------------------------------------------------------------------------------------- 23
8. System Reporting Codes (4 x 2 and Domestic) ------------------------------------------------28
9. System Programmable Outputs----------------------------------------------------------------------30
10. System Clock Options-----------------------------------------------------------------------------------32
11. Communicator Options ---------------------------------------------------------------------------------34
11.1 Programming Telephone Numbers --------------------------------------------------------------------- 40
11.2 Telephone Number Storage Locations----------------------------------------------------------------- 41
11.3 Download Options ------------------------------------------------------------------------------------------ 41
12. Partition Setup ---------------------------------------------------------------------------------------42
13. User Options ---------------------------------------------------------------------------------------48

IDS 816 700-283-02IIssuedSeptember2009
4
14. Programmable Output Options-----------------------------------------------------------------------49
15. Keypad Options ---------------------------------------------------------------------------------------51
16. Installer Options ---------------------------------------------------------------------------------------52
Index of Programming Locations------------------------------------------------------------------------------53
Index ---------------------------------------------------------------------------------------56

IDS 816 700-283-02IIssuedSeptember2009
5
Figures
Figure 1 : Connection Diagram without Tamper per Zone -------------------------------------------- 9
Figure 2 : Tamper by Zone Connection---------------------------------------------------------------------10
Figure 3 : Zone Doubling Connection -----------------------------------------------------------------------11
Figure 4 : Resistors (Tamper per Zone or Zone Doubling) ------------------------------------------11
Figure 5 : Programmable Output Configuration ---------------------------------------------------------12
Figure 6 : Fire Detect Output Sequence --------------------------------------------------------------------32
Tables
Table 1 : Values Represented by Each Zone LED-------------------------------------------------------16
Table 2 : Hexadecimal Value -----------------------------------------------------------------------------------17
Table 3 : Location / Zone Defaults----------------------------------------------------------------------------19
Table 4 : Programmable Zone Types ------------------------------------------------------------------------20
Table 5 : Programmable Output Numbering --------------------------------------------------------------30
Table 6 : Output Actions--------------------------------------------------------------------------- -------------30
Table 7 : Event Driven Programmable Outputs ----------------------------------------------------------31
Table 8 : Function Driven Programmable Outputs------------------------------------------------------31
Table 9 : Value for Day of the Week--------------------------------------------------------------------------33
Table 10 : Standard Contact ID Reporting Codes -------------------------------------------------------37
Table 11 : User Code Locations--------------------------------------------------------------------------------48

IDS 816 700-283-02IIssuedSeptember2009
6

IDS 816 700-283-02IIssuedSeptember2009
7

IDS 816 700-283-02IIssuedSeptember2009
8
1. Introduction to the IDS 816
The IDS 816 is a versatile, microprocessor based eight zone Alarm Panel. It has two partitions and can be
expanded to sixteen zones. Most features are optional and may be programmed either directly through
the keypads or via the telephone system, using the IDS download software and appropriate modem.
There are eight programmable burglary zones, a dedicated panic zone, monitored siren output, auxiliary
power outputs and five programmable outputs, which may be programmed to perform various,
trigger/switching functions.
For correct operation, the IDS 816 must be used in conjunction with the specified transformer/battery
combination and appropriate peripheral sensors and signalling devices.
1.1 Features of the IDS 816
Eight programmable, end-of-line supervised zone inputs
Expandable to sixteen zones via keypad zones, zone expander module, zone doubling or
wireless expansion.
2 partitions
Optional tamper reporting per zone using double end-of-line resistors (12K and 4K7)
Fully programmable digital telephone communicator that supports most industry standard
formats.
Five programmable outputs on alarm panel. Expandable to seven when using Wired Zone
Expander module.
Non volatile EEPROM memory retains all program and event log data in the event of a total power
failure
Programmable loop response time
Up and downloadable using IDS Windows based software, either directly via RS 232 or remotely
using a modem.
Excellent protection against lightning (provided by specialised “zap tracking” and transient
suppressors)
Auto arm/disarm capability per partition and by day of the week. The panel can be programmed
to arm/disarm at a pre-determined time
Fax defeat/answering machine override
Dual reporting provides for duplicated reporting to two independent central base stations.
Dynamic battery self test
Low battery cut out circuit

IDS 816 700-283-02IIssuedSeptember2009
9
2. Installation and Wiring
Please refer to Figure 1: Connection Diagram and familiarise yourself with the following sections.
Figure 1 : Connection Diagram without Tamper per Zone

IDS 816 700-283-02IIssuedSeptember2009
10
2.1 Additional Technical Data
A suitable transformer with an output voltage of 16 volts AC ±10% with a 16VA minimum rating
must be used. A 32 VA transformer is recommended for larger installations.
A 12V sealed lead acid battery with a minimum capacity of 7AH must be used. The back up
period after mains failure will depend on the number of keypads, sensors and peripheral devices
connected to the system.
The panel can supply a total continuous current of 750mA to peripheral devices such as keypads,
remotes, receivers, passives etc.
Connect a 12-volt self-driven siren or piezo siren [not a horn speaker] to the siren output.
2.2 End-of-Line Resistors
(Including Tamper by Zone / Zone Doubling)
All zones must be end-of-line supervised.
Any unused zones must be terminated with a 3K3 resistor. The end of line resistor must be
placed inside or as close to the sensor as possible.
If neither zone doubling nor tamper by zone are required the 3K3 resistor must be used.
For zone doubling or tamper per zone, the 4K7 and 12K end-of-line resistors must be connected
as per Figures 2 and 3.
Figure 2 : Tamper by Zone Connection
Tamper operation is as follows:
If the panel is unarmed and a tamper condition occurs, the siren will not sound but a tamper
condition will be reported.
If the panel is armed and a tamper condition occurs an audible alarm will register and a tamper
condition AND zone violation will be reported.
Panic zones always register panic and tamper conditions.
The colour codes for the 12K and 4K7 resistors are as per in Figure 4.