IDTECK Star LX505 User manual
Table of Contents
ii
Table of Contents
1 Safety Information
1 IMPORTANT SAFETY INSTRUCTIONS
2 General
3 Features
4 Specification
5 Identifying Supplied Parts
6 Product Overview
1 Features
2 Product Explanation
2.1 Panel Description
2.2 Connection Layout
2.3 Color Coded & Wring Table
7 Installation Tips & Check Points
1 Check Points before Installation
1.1 Selection of Cable
1.2 Recommended Cable Type and Permissible Length
2 Check Point during Installation
2.1 Termination Resistor
2.2 How to Connect Termination Resistors
2.3 Grounding System for Communication Cable
2.4 Reverse Diode Connection
...................................................... ii
................................................... 1
......................................... 3
........................................................... 4
........................................................... 5
....................................................... 6
............................................. 8
................................................... 9
............................................................... 9
...................................................... 11
...................................................... 12
..................................................... 12
.............................................. 13
......................................... 14
............................................. 14
..................................................... 14
............................ 15
.............................................. 15
.................................................... 15
..................................... 16
................................ 16
............................................... 17
p.iii
8 Installation of Product
1 Wall Mount (Unit: mm)
2 System Initialization
3 Wall Mount Installation
4 Wiring
4.1 Power Connection
4.2 Input Connection
Exit Button Connection
Door Contact Sensor Connection
Auxiliary Input Connection
2.2K Resistor Connection for Cut off Check
4.3 Output Connection
Door Lock (Power Fail Safe) Connection (Door Relay)
Door Lock (Power Fail Secure) Connection (Door Relay)
Alarm Device Connection (Alarm Relay)
4.4 External Reader Connection
Proximity Reader Connection
Compatible Readers (External Reader):
LX505:
LX505SR:
Recommended Readers
LX505
LX505SR
9 Communication
1 RS232 Communication Port Connection
2 RS485 Communication Port Connection
2.1 RS485 Connection (Standalone Unit)
2.2 RS485 Connection (Multiple Units)
3 TCP/IP Communication Port Connection (Optional)
4 Serial Printer Connection
10 Basic Setting
1 Initialization of LX505
2 How to Enter the SETUP MENU
3 Language Setting
4 Date / Time Setting
................................................ 18
................................................... 18
...................................................... 19
................................................... 19
................................................................ 20
..................................................... 20
...................................................... 20
................................................... 20
........................................... 20
................................................ 20
................................... 21
.................................................... 21
........................... 21
......................... 21
...................................... 21
.............................................. 22
.............................................. 22
...................................... 22
.............................................................. 22
............................................................ 22
.................................................. 23
.............................................................. 23
............................................................ 23
..................................................... 24
...................................... 24
...................................... 25
...................................... 25
........................................ 25
............................. 26
.................................................. 27
...................................................... 29
.................................................... 29
............................................. 30
........................................................ 30
...................................................... 31
Table of Contentsp.iv
5 ID Registration
5.1 Registration by Card
5.2 Registration Using Keypad(PIN)
5.3 Terminology
11 OPERATIONS
1 Normal Operation
2 Default Setting
12 Setting Changes
1 F1 SETUP MENU
1.1 Language
1.2 Date and Time Setting
1.3 Reader #1 Mode
1.4 Reader #2 Mode
1.5 Reader #1 KEY Input
1.6 Reader #2 KEY Input
1.7 Communication Address Setting
1.8 Baud Rate Setting
2 F2 SETUP MENU
2.1 Event Memory
2.2 ID Display
2.3 Time Unit Setting
2.4 Output T/S + ID
2.5 Anti-passback Mode
2.6 Duress Mode
2.7 Wiegand Output
2.8 Door Open Alarm Time Setting
3 F3 SETUP MENU
3.1 Print Output
3.2 Voice Volume
3.3 Arm/Disarm Setting
3.4 Two Men Mode
3.5 One Time Read
3.6 Max. User Setup
3.7 Name Display
4 F4 SETUP MENU
.......................................................... 31
.................................................... 32
........................................... 32
.......................................................... 32
...................................................... 35
....................................................... 35
.......................................................... 35
................................................... 36
......................................................... 37
............................................................ 38
.................................................. 38
...................................................... 38
...................................................... 39
................................................... 39
................................................... 39
.......................................... 40
...................................................... 40
......................................................... 41
........................................................ 42
............................................................ 42
...................................................... 43
....................................................... 43
................................................... 44
......................................................... 45
...................................................... 45
........................................... 46
......................................................... 47
.......................................................... 47
......................................................... 48
.................................................... 49
....................................................... 49
........................................................ 50
....................................................... 50
......................................................... 50
......................................................... 51
p.v
4.1 Time Schedule
4.2 Holiday Setting
4.3 Holiday Code
4.4 Reader#1 Mode Time Schedule
4.5 Reader#2 Mode Time Schedule
4.6 Voice Time Schedule
5 F5 SETUP MENU
5.1 Exit Button Output Setting
5.2 Door Contact Output Setting
5.3 Aux Input#1 Output Setting
5.4 Aux Input#2 Output Setting
5.5 Tamper Alarm Output Setting
5.6 Cut Off Alarm Output Setting
5.7 Duress Alarm Output Setting
5.8 Arm/Disarm Output Setting
5.9 Door Time Output Setting
5.10 Output Time Schedule Setting
5.11 Input Time Schedule Setting
5.12 Cut Off Check Setting
5.13 Input Type Setting
6 F6 SETUP MENU
6.1 Output Setting for Reader#1 ID OK Level 1
6.2 Output Setting for Reader#1 ID OK Level 2
6.3 Output Setting for Reader#1 ID OK Level 3
6.4 Output Setting for Reader#1 ID OK Level 4
6.5 Output Setting for Reader#1 ID Error
6.6 Output Setting for Reader#1 T/S Error
6.7 Output Setting for Reader#1 APB Error
6.8 Output Setting for Reader#2 ID OK Level 1
6.9 Output Setting for Reader#2 ID OK Level 2
6.10 Output Setting for Reader#2 ID OK Level 3
6.11 Output Setting for Reader#2 ID OK Level 4
6.12 Output Setting for Reader#2 ID Error
6.13 Output Setting for Reader#2 T/S Error
6.14 Output Setting for Reader#2 APB Error
7 F7 SETUP MENU
........................................................ 52
........................................................ 52
......................................................... 53
........................................... 53
........................................... 54
................................................... 54
......................................................... 55
............................................... 56
............................................. 57
.............................................. 57
.............................................. 57
............................................ 57
............................................ 57
............................................. 57
.............................................. 57
............................................... 57
........................................... 57
............................................ 58
................................................. 59
.................................................... 59
......................................................... 60
.................................. 61
.................................. 62
.................................. 62
.................................. 62
....................................... 62
...................................... 62
..................................... 62
.................................. 63
.................................. 63
................................. 63
................................. 63
..................................... 63
..................................... 63
.................................... 63
......................................................... 64
Table of Contentsp.vi
7.1 ID Registration
Registration by Card
Registration Using Keypad
Terminology
7.2 ID Delete
7.3 ID List
7.4 Master ID Registration
Master ID Registration by Card
Master ID Registration by PIN
7.5 Registered ID Count
7.6 Event Count
8 F8 SETUP MENU
8.1 System Initialization
8.2 Event Clear
8.3 All ID Clear
8.4 Master ID Clear
8.5 Time Schedule Clear
8.6 Default Setting
9 F9 SETUP MENU
9.1 Firmware Version Check
9.2 Input Test
9.3 Output Test
9.4 LCD Test
9.5 Keypad Test
9.6 Reader Test
9.7 Memory Test
9.8 Communication Test
13 Appendix
1 A. THE RELATION BETWEEN INPUT AND OUTPUT (DEFAULT)
2 TROUBLESHOOTING
14 FCC REGISTRATION INFORMATION
15 RMA Request
........................................................ 64
..................................................... 64
................................................ 65
........................................................... 65
............................................................ 66
............................................................... 67
.................................................. 67
............................................. 68
.............................................. 68
.................................................... 68
.......................................................... 69
......................................................... 69
.................................................... 70
........................................................... 70
........................................................... 71
........................................................ 71
.................................................... 71
........................................................ 72
......................................................... 73
................................................. 73
............................................................ 74
.......................................................... 74
............................................................. 74
.......................................................... 75
.......................................................... 75
......................................................... 75
................................................... 76
......................................................... 77
...................... 77
..................................................... 79
.................................... 83
..................................................... 84
Safety Information 1
p.1
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIE
D SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric shock is pres
ent within this unit.
This exclamation point symbol is intended to alert the user to the presence of importa
nt operating and maintenance (servicing) instructions in the literature accompanying the ap
pliance.
WARNING
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet. Usin
g any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.
Safety Informationp.2
3. Do not connect multiple controllers to a single adapter. Exceeding the capacity may cau
se abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may caus
e fire.
5. When installing the controller, fasten it securely and firmly. The fall of controller may ca
use personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or container
s filled with water on top of the controller. Doing so may cause personal injury due to fi
re, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or el
ectric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case,
immediately disconnect the power source and contact the service center. Continued us
e in such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disass
emble or modify this product in any way. (SAMSUNG is not liable for problems caused
by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may ca
use fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a locat
ion subject to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature (b
elow -30°C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and
then move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to d
o so may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the controller directly towards extremely bright objects such as sun.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liqui
ds, such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any tim
e.
p.3IMPORTANT SAFETY INSTRUCTIONS
1IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s ins
tructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two bla
des and a third grounding prong. The wide blade or the third prong is provided for you
r safety. If the provided plug does not fit into your outlet, consult an electrician for repla
cement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenie
nce receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sol
d with the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparat
us combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparat
us has been damaged in any way, such as power supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the apparatus has been expo
sed to rain or moisture, does not operate normally, or has been dropped.
General 2
p.4
The IDTECK LX505 / LX505SR is ideal to be used for Single Door Access Control and Time &
Attendance. The IDTECK LX505 / LX505SR has 4 input ports, 2 Form-C relay outputs, 2 TTL
outputs, an RS232/RS485 communication port and an optional TCP/IP communication port
to meet various customer requirements.
This user-friendly device allows you to register up to 10,000 IDs and 20,000 event transactio
ns. All events can be uploaded and saved to the database of the host PC and the software c
an create a report in the MS-Excel, HTML and Text file formats for Time & Attendance mana
gement purposes.
The IDTECK LX505 / LX505SR has a built-in proximity card reader with IDC 26bit Wiegand f
ormat and a 24-key keypad (10 numeric keys, 2 control keys and 12 function keys) for a wid
e range of applications. The IDTECK LX505 / LX505SR controls access of users with any selec
ted combination of Proximity Card/PIN and/or password. The IDTECK LX505 / LX505SR has
4 external input ports to be connected to an exit button, a motion detector, a door contact
sensor and an existing alarm system to prevent unauthorized access.
The IDTECK LX505 / LX505SR has 2 relay outputs to control a door lock and an alarm relay t
hat is used to warn any error. The graphic LCD supports multiple languages so that the unit
can be operated anywhere in the world.
All setup menus can be programmed using the front keypad or via the Windows-based soft
ware. The IDTECK LX505 / LX505SR is a cost effective system that can be used stand alone o
r networked. Dual tamper switches prevent unauthorized access.
Features 3
p.5
●125KHz(default) proximity/13.56MHz(optional) contactless smart card reader and PIN
●Dual function for Access Control and Time & Attendance
●Register 10,000/20,000 Users & 20,000/10,000 Event Buffers (Selectable)
●Operating Mode selectable for each user ID
●4 Level Door Open Time Setting for Individual ID
●Time Schedules Setting for each user ID, input port, output port and Reader Mode
●Network Communication via RS232, RS485 and built-in TCP/IP
●26bit Wiegand Output (34bit for LX505SR) / Baud rate : 57,600bps
●Serial Printer Port for event ticket issuing
●Supervised Input Cut-off Check
●User Name & Function Key Definition Display on LCD
●ARM/DISARM Function for Alarm Panel
●2 Men Operation Mode
●Duress Alarm Function
●Multiple Master IDs Registration
●Able to Activate Time Schedule using User Card
●Graphic LCD of Multi Languages Display
●Voice Guide Programmable for Other Language
●Compatible Software : STARWATCH TIME PRO, STARWATCH LX ACCESS PRO II, STAR
WATCH STANDARD
●13.56MHz Contactless SMART Card Access Controller(LX505SR)
Specification 4
p.6
Model LX505
CPU 8bit and 16bit Microprocessor
Memory Program Mem
ory
256K Byte ROM, 512K Byte SDRAM
Data Memory 512KByte Flash Memory
User 10,000 / 20,000 ID Users
(Selectable)
Event Buffer 10,000 / 20,000 Event Buffers (Selectable)
Range LX505
IDC80 / IDC170 : Up to 4 inches (10cm)
LX505SR
IHC80: Up to 2 inches (5cm) ISC80: Up to 4 inches (10cm)
Reading Time (Card) 30ms
Power / Current DC 12V / Max.550mA
LX505: 1 Port for Anti-Pass Back
(26bit Wiegand, 8bit Burst for PIN) LX505SR: 1 Port for Anti-Pass
Back (34bit Wiegand, 8bit Burst for PIN)
Communication RS232 / RS485 (Max.32ch)
TCP/IP (Internal LAN Converter required (Optional))
Baud Rate 57,600bps (Default) / 9,600bps /
19,200bps / 38,400bps (selectable)
4 Ports : Exit Button, Door Sensor, Aux# 1, Aux#2
2 Ports : 2 FORM-C Relay Output (COM, NO, NC)
/ DC12V~18V, Rating Max.2A
2 Ports :TTL Output
p.7
/ DC5V, Rating Max.20mA
LCD Graphic LCD (128 x 64 dots)
72.5mm x 39.5mm (2.85” x 1.56”)
Keypad 24-key Keypad with Back Lighting
(12 Function Keys included)
Language LCD Display English, Spanish, Portuguese (Selectable)
Arabic, Chinese, Korean, Japanese (Optional)
Voice Output English(Default), Spanish, Portuguese, Arabic, Chinese, Korean, Ja
panese (Programmable)
LED Indicator 3 Array LED Indicators
(Red, Green and Yellow)
Beeper Piezo Buzzer
Operating Tem
perature
LCD 0 to +50C (+32 to +122F)
Controller -15 to +70C (+5 to +158F)
RF Reader -35 to + 65C (-31 to +149F)
Operating Humidity 10% to 90% relative humidity
(non-condensing)
Color / Material Black, Red Wine, Silver, Dark Gray, Black & Gold Combo / Polycarb
onate
Dimension (W x H x T) 192mm x 160mm x 45mm (7.56”x6.29”x1.77mm)
Weight 800g(1.76lbs)
Certification FCC, CE, KC
Identifying Supplied Parts 5
p.8
Please unpack and check the contents of the box. If any of these parts are missing, please co
ntact a near-by distributor or IDTECK as soon as possible.
Product Overview 6
p.9
1Features
Standalone Operation
The IDTECK LX505 / LX505SR is capable of having an external reader (for 1 Door Con
trol). This access controller reads card ID numbers and determines whether to allow o
r deny access to the door. When an input signal is received, for example from a senso
r activated or an exit button pressed, the controller generates and logs an appropriate
response. All events are stored into the memory buffers. The access controller is a true
standalone device that, in the event of malfunction, will not affect other units when u
sed in conjunction with one another.
Operation with Host PC
All event transactions can be managed via the host PC. The data transmitted from the
controller can be displayed and stored on the host PC.
Keypad
If the IDTECK LX505 / LX505SR is not connected to the host PC, the built-in keypad a
nd LCD module can be used for the entire operations and configuration process.
Input / Output
The IDTECK LX505 / LX505SR has 4 built-in input ports and 4 output ports (2 relay ou
tputs and 2 TTL outputs) which can be used to manipulate a wide variety of controls.
Product Overviewp.10
Time Schedule Setup
You can program up to 10 time schedules and assign one time schedule to each user.
Each time schedule has 8 different time zones from Monday-Sunday (7 time zones) a
nd one holiday. Each time zone has 5 different time codes so you can program 5 diffe
rent time codes for each day. You can also program time schedules for individual inpu
ts and outputs. That is, if a time schedule for an input device is activated, that input d
evice will be working only during the time assigned by that time code. Each time sche
dule is linked to one holiday schedule.
Holiday Schedule Setup
Excepting Sunday, you can program 100 holidays to one holiday schedule. Each holid
ay schedule is linked to one time schedule which has a time code for holidays. You ca
n program all holidays to a holiday schedule and the time code for holidays is progra
mmed to be the holiday time zone of time schedule.
Example:
A.Holiday schedule 01 linked to time schedule 01,
Holiday schedule 02 linked to time schedule 02
B.Holiday schedule 02 linked to time schedule 01,
Holiday schedule 01 linked to time schedule 03
Forced Door Open Alarm
When the door is opened by force, the door contact sensor will be activated. For this
application, you have to install the door contact sensor and properly set the door cont
act time and outputs to the alarm devices. The Forced Door Open Alarm will be gener
ated until the alarm is disconnected.
Door Open Timeout Alarm
The Door Open Timeout Alarm will be generated when the door is open for longer th
an a certain time limit, even after the door is opened followed by a normal authentica
tion process. The Overtime Door Open Alarm will continue to ring until the door is clo
sed.
Anti-pass Back
If an additional proximity reader is used, the Anti-pass back mode can be applied. In t
he Anti-pass back mode, a user is not allowed to enter or exit when the user violates t
he one entry/one exit rule. For example, an identical user won’t be able to enter if he
or she previously exited the door without going through a proper authentication proc
ess.
p.11Product Explanation
Duress Alarm
In case of duress, enter the 2-digit Duress Password and press the <ENT> key before t
he normal access process. The door can be opened as usual, but the duress alarm is al
so generated at the same time. The duress alarm output will be sent to the TTL outpu
t and an alarm event will be sent to the host PC.
ARM / DISARM Function for Alarm Panel
While a device is in the ARM condition, its reader ports are all frozen and inputs to th
e ports are not processed so that no one can get access to the door. When this mode
is applied, the IDTECK LX505 / LX505SR sends signals to other connected security dev
ices so that they can function accordingly.
Two Men Operation
This feature is used to configure the IDTECK LX505 / LX505SR to allow a certain user
(e.g. a visitor) to pass the door only when that user is accompanied by another special
user (e.g. a guide). Both of the visitor and the guide should be authorized together fo
r access.
4 Level Individual Door Opening Time Setting
This feature is used only for setting four different door opening times.
Name Display
The IDTECK LX505 / LX505SR can display the user name when a user gains access.
Function Key Name Display
You can assign names for each function key via software. Using this feature, for exam
ple, you can give certain keys names like punch-in and punch-out and tell the employ
ees to press one of the function keys according to the nature of their access prior to e
ach access attempt. This way, you will be able to identify punch-in and punch-out eve
nts on the software.
2Product Explanation
Product Overviewp.12
2.1 Panel Description
LCD Module
The LCD screen displays the status of the LX505.
System Operation Status LED:
When the power is applied to the LX505, the red LED is turned on.
When the Relay #1 operates, the green LED is turned on.
When the Relay #2 operates, the yellow LED is turned on.
24-key Keypad
The keypad can be used to manually operate the LX505 with ease.
Function Keys
The LX505 has 12 function keys ([F1] - [F12]).
2.2 Connection Layout
p.13Product Explanation
2.3 Color Coded & Wring Table
I/O PORT NAME SIGNAL NAME WIRE COLOR
CON-1(2PIN CONNECTOR)
Main Power (+12V) DC 12V Red
Power Ground GND (-) Black
CON-2 (3PIN CONNECTOR : Serial Printer)
RS232-RX RXD Pink wire with white stripe
RS232-TX TXD Cyan wire with white stripe
RS232-GND GND Black
CON-3 (6PIN CONNECTOR)
TTL OUTPUT #1 TTL#1, WD0 Orange wire with white stripe
TTL OUTPUT #2 TTL#2, WD1 Brown wire with white stripe
Aux Input #1 IN#1 Green
Aux Input #2 IN#2 Green wire with white stripe
Wiegand DATA 0 DATA-0 Pink
Wiegand DATA 1 DATA-1 Cyan
CON-4 (5PIN CONNECTOR)
RS485-RTX(+) RS485-A(+) Yellow wire
RS485-RTX(-) RS485-B(-) Gray wire
RS232-TX TXD Black wire with white stripe
RS232-RX RXD Red wire with white stripe
RS232-GND GND Black
CON-5 (8PIN CONNECTOR)
Door RELAY(NC) NC(1) Blue wire with white stripe
Door RELAY(COM) COM(1) Gray wire with red stripe
Door RELAY(NO) NO(1) White wire with red stripe
Alarm RELAY(NC) NC(2) Purple wire with white stripe
Alarm RELAY(COM) COM(2) White
Alarm RELAY(NO) NO(2) Purple
Exit Button EXIT
Door Sensor CONTACT Yellow wire with red stripe
CON-6 (4PIN CONNECTOR : Not Use)
CON-7: TCP/IP RJ45 CONNECTOR
Installation Tips & Check Points 7
p.14
1Check Points before Installation
1.1 Selection of Cable
The system installation cables should be connected as follows;
Other manuals for Star LX505
3
This manual suits for next models
1
Table of contents
Other IDTECK IP Access Controllers manuals
IDTECK
IDTECK iPass IP-RFL200 User manual
IDTECK
IDTECK Star Finger007 User manual
IDTECK
IDTECK Star 505R User manual
IDTECK
IDTECK GE313 User manual
IDTECK
IDTECK Star 505R User manual
IDTECK
IDTECK Star FINGER006 User manual
IDTECK
IDTECK iTDC EIO8 User manual
IDTECK
IDTECK LX007 User manual
IDTECK
IDTECK iTDC Operating instructions
IDTECK
IDTECK Star LX505 User manual
IDTECK
IDTECK Star LX505 User manual
IDTECK
IDTECK Star Finger007 User manual
IDTECK
IDTECK Star iCON100 User manual
IDTECK
IDTECK FINGER007 Series User manual
IDTECK
IDTECK Star FINGER006 User manual
IDTECK
IDTECK Star iCON100 User manual
IDTECK
IDTECK Star 505R User manual
IDTECK
IDTECK Star iCON100 User manual
IDTECK
IDTECK iPass IP-RFL200 User manual
IDTECK
IDTECK ITDC ITDCSR EIO88 User manual
Popular IP Access Controllers manuals by other brands
Zennio
Zennio Securel ZIO-SEC user manual
Essex Electronics
Essex Electronics iSmartSE user guide
Kantech
Kantech Ethernet Four-Door Controller KT-400 installation manual
ZKTeco
ZKTeco BioPro SA30 installation guide
Matrix
Matrix COSEC EBS200 How to reset
Moniteq
Moniteq Crypto-Lock CC-8521B instruction manual
Roger
Roger MC16-PAC-16 installation manual
Visonic Networks
Visonic Networks TAG-IN-A-BAG Installation and programming guide
Code
Code ME24 user manual
Ruijie
Ruijie RG-SC6705-SP Hardware installation and reference guide
Ness
Ness IDTECK iCON100 user manual
Visionis
Visionis VS-AXESS-4D-ETL-PCB installation manual