IDTECK Star iCON100 User manual

Quick Install Guide
1
1. Check Environment
1.1 Check the power source
Before wiring, please check the voltage/current (DC12V/350mA) that will be input to the iCON100.
1.2 Connection Diagram

Quick Install Guide
2
2. Setup Hardware
2.1 Backup Battery setup and Hardware Initialization
2.1.1 It explains how to operate the switch for connecting the backup battery in order to keep the memory data.
For normal use, the switch should be connected as the picture below so that there is no any data loss.
Figure: JUMPER SETTING Figure: Jumper location
2.1.2 Toggle the DIP switch ‘8’ “OFF” while the power is ON.
2.1.3 The message “Turn on DIP 8Turn OFF Power…” will be shown on the LCD.
2.1.4 Toggle the DIP switch ‘8’ “ON” and turn the power off.
2.1.5 There is 8-bit DIP Switch for address setting and it turns to 5-bit binary code as below. Each bit has fixed address value
and the address is calculated by the sum of the value of each bit set to “1” position.
Example
Turn on DIP 8
T
u
rn
O
FF P
o
w
e
r⋯

Quick Install Guide
3
3. Setup Controller parameter
3.1 Mode setting (F1 Menu)
3.2 Date/Time setting (Select “TIME SETTING” Menu by the Key ‘4’or ‘6’)
3.3 Card Registration (Enter F3)
Start Display
STAR iCON100 [F1]
01/01 00:00:15 READER1 MODE
RF
O
NLY
Enter Default Master No.
(
00000000
)
Key ‘4’or ‘6’: Left/Right
Key ‘2’or ‘8’: Up/Down
ENT: Change or Enter
ESC: Cancel
☞In the case of iCON100SR, Press <0> key (Default setting “0000000000”) 10 times
to enter the SETUP MENU.
Enter the setup mode
Display for Mode Selection
RF Only: Card
RF + P/W: Card + Password
<ENT>
READER1 MODE
-> RF
O
NLY
READER1 MODE
RF
O
NLY
TIME SETTING YYYYMMDDhhmmssW
200405101230302
<ENT>
Display for Date/Time setting
YYYY: Year, MM: Month, DD: Date
hh: Hour (24 hour-system), mm: Minute, ss: Second
W: Sun=1, Mon=2, Tue=3, Wed=4, Thu=5, Fri=6, Sat=7
Example: 200405101230302 => 12:30:30, Monday, May 10, 2004
<ENT>
<ENT>
STARiCON100 [F1]
01/20 09:01:23
Select <F3>
[
ID REGISTRATION]
selection
“00000000” + <ENT>
“Master No.” + <ENT>
ID REGISTRATION
ID REGISTRATION
1-CARD, 2-KEY
<ENT>
* Change the mode by the key left/right (4 or 6).

Quick Install Guide
4
3.3.1. Registration with the Card
3.3.2. Registration with Keypad
3.4 Delete Card (Select “ID DELETE” Menu by the Key ‘4’ or ‘6’)
Registration Completed
1. CARD: Card Reading
2. KEY: Enter 8-digit (iCON100SR: 10 digit) PIN
< INPUTTHE ID INFORMATION >
ID : 8-digit (iCON100SR: 10 digit) card Number.
TS : Time Schedule code (Enter the default setting value “00”)
-EntersuchcodeforapplyingT/S
RD: Setup to use the reader or not (Enter the default setting value “3”)
1 – To be read only by the reader 1
2 – To be read only by the reader 2
3 – To be read by the both readers
Enter 8-digit (iCON100SR: 10 digit)
card number to be deleted.
<ENT>
Display for ID Delete
ID DELETE
Enter Card No.
->__________
Scanning ⋯
12345678
PW____ TS__ RD_
Card approach
PW (4 digit) + <ENT>
TS Code + <ENT>
Use Door or not + <ENT>
ID Registered
Registration completed
[______]
PW____ TS__ RD_
12345678
PW____ TS__ RD_
ID(8 digit)
+ <ENT>
<2>Select
PW (4 digit) + <ENT>
TS Code+ <ENT>
Use door or not + <ENT>
ID Registered
<1>Select
* Refer to the Manu setup
* Input the ID information
* Input the ID information
<ENT>

Quick Install Guide
5
4. Normal Operation
4.1 Power ON
When the power is applied to iCON100, the Red LED (LED1) is turned on.
4.2 Registered card reading
When a registered card (or PIN) is read, the Door (Relay 1) will be opened for 3 seconds (Default) with the Green LED (LED2)
light on.
4.3 Exit Button
The Exit Button or the Exit Reader should be installed inside.
When the Exit Button is pressed, the door will be opened for 3 seconds with the Green LED (LED2) light on.
4.4 Alarm (Unregistered ID/PW Error/TS Error/Door Error)
When an unregistered card is read, or any wrong password is input, or any error over the time schedule and the door access is
occurred, the access is denied and the alarm will be activated for 3 seconds (Default) with the Yellow LED (LED 3) light on.
LED1: Power ON/OFF Status
LED2: Door Relay Status
LED3:Alarm Relay Status
1 23