IDTECK iPass IP-RFL200 User manual

Table of Contents
ii
Table of Contents
1 Safety Information
1 IMPORTANT SAFETY INSTRUCTIONS
2 General
3 Features
4 Identifying Supplied Parts
5 Specification
6 Installation
7 Color Coded & Wiring Table
8 Wire Connection to Controller
1 Connecting a power supply
2 Connecting a door lock
3 Connecting an exit button
4 Connecting a door contact
5 Connecting a door lock depending on the lock type
9 Operation
1 When power is supplied
2 When registered key tag is read on RFL200 / IP-RFL200 or an exit button is pressed.
3 When unregistered key tag is read on RFL200 / IP-RFL200
4 If key tag is approached by RFL200 / IP-RFL200 when the door is opened.
5 When a key tag is deleted or registered
6 When a master card is deleted or registered again
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
. . . . 13
. . . . . . . . . . . . . . . . . . . . . . . . 13
. . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

p.iii
7 When a product is initialized by using a master card
8 When a product is initialized by wiring the cable
10 FCC REGISTRATION INFORMATION
11 RMA Request
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Safety Information 1
p.1
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIE
D SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric shock is pres
ent within this unit.
This exclamation point symbol is intended to alert the user to the presence of importa
nt operating and maintenance (servicing) instructions in the literature accompanying the ap
pliance.
WARNING
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet. Usin
g any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.

p.2
3. Do not connect multiple controllers to a single adapter. Exceeding the capacity may cau
se abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may caus
e fire.
5. When installing the controller, fasten it securely and firmly. The fall of controller may ca
use personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or container
s filled with water on top of the controller. Doing so may cause personal injury due to fi
re, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or el
ectric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case,
immediately disconnect the power source and contact the service center. Continued us
e in such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disass
emble or modify this product in any way. (SAMSUNG is not liable for problems caused
by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may ca
use fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a locat
ion subject to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature (b
elow -30°C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and
then move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to d
o so may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the controller directly towards extremely bright objects such as sun.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liqui
ds, such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any tim
e.

Safety Informationp.3
1IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s ins
tructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two bla
des and a third grounding prong. The wide blade or the third prong is provided for you
r safety. If the provided plug does not fit into your outlet, consult an electrician for repla
cement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenie
nce receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sol
d with the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparat
us combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparat
us has been damaged in any way, such as power supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the apparatus has been expo
sed to rain or moisture, does not operate normally, or has been dropped.

General 2
p.4
The Star RFL200 / iPASS IP-RFL200 is an elegant looking and an attractive 4" read range pro
ximity reader built-in Proximity Single Door Access Controller which can be mounted to a m
etal door frame (mullion) or to any flat wall surface. The
Star RFL200 / iPASS IP-RFL200 is epoxy potted that ensure you a successful operation even i
n harsh environments. Using 512 key tag, not only controlling door but also convenient regi
stration or deletion.
When loosing a key tag, it is easy to reset. Therefore it is the safest controlling door device.
Two-color LED of green and red, internal Piezo buzzer sound will guarantee you an accurate
and reliable Door Access Operations.

Features 3
p.5
●125KHz Standalone Proximity Access Controller
●Star RFL200: PSK Modulation
iPASS IP-RFL200: ASK[EM] Format
●512 Users including One Master Card
●Standalone (No need application software)
●Direct Control of Door Lock
●Power Fail Safe or Power Fail Secure Locks selectable
●Solid Epoxy Potted
●Waterproof
●Warranty: Life Time

Identifying Supplied Parts 4
p.6
Please unpack and check the contents of the box.

Specification 5
p.7
Model RFL200 IP-RFL200
CPU Dual 8bit Microprocessor
Memory Program Memory 64KByte Flash ROM
Data Memory 4KByte EEPROM
User 512 Users (Including 1 Master Card)
Range IDC80 / IDC170: Up to 4 inches
(10cm)
IPC80 / IPC170: Up to 4 inches
(10cm)
Reading Time (Card) 30ms
Door Open Time 5 sec (fixed)
Power / Current DC 12V / Max.150mA
Input Port 3 Ports (Exit Button, Door Contact,
Door Lock Type (Power Fail Safe / Power Fail Secure))
Output Port 2 Ports (TR Output / Open Collector Output
Rating Max 300mA Alarm Output, 1A Lock Output
LED Indicator /
Beeper
9 Array LED Indicators (Red and Green) /
Piezo Buzzer
Operating Temper
ature
Controlle
r
-35 to +60C (-31 to +140F)
RF Reade
r
-35 to +65C (-31 to +149F)
Operating Humidity 10% to 90% relative humidity non-condensing
Color / Material Dark Pearl Gray / Polycarbonate
Dimension (W x H x T) /
Weight
1.8” x 4.9” x 0.8” (45mm x 124m x 19.64mm) /
80g (0.18 lbs)

p.8
Warranty Life Time
Certification FCC, CE, KC
Reading of key fob-type tags may not work properly at temperatures below 0°C or
32°F

Installation 6
p.9
1. Drill one 0.5”(12.7mm) hole at the central of the RFL200 / IP-RFL200 on mullion or wall
mount.
Route the cable of reader module through the central hole.
2. Drill one 0.39"(10mm) in right horizontal and 1.74"(44.4mm) in upper vertical through
the central hole.
And drill the other 0.33"(8.5mm) in left horizontal and 1.59”(40.6mm) in under vertical
through the central hole.
3. Push reader module on mullion or wall mount then install the main unit using two 6-32
or M3 screws.
4. Put the bezel on the reader module and then pushes it to fix up.

Color Coded & Wiring Table 7
p.10

Wire Connection to Controller 8
p.11
Select lock type as shown below.
 Power Fail Safe Mode (Always open at power off)
: Connect lock type of Yellow with Black wire.
 Power Fail Secure Mode (Always close at power off)
: Disconnect lock type of Yellow wire.
1Connecting a power supply

p.12Connecting a door lock depending on the lock type
●Connect +12V of power supply to Red wire.
●Connect GND of power supply to Black wire.
2Connecting a door lock
●Connect (+) wire of door lock to +12V wire of power supply.
●Connect (-) wire of door lock to white wire of reader module.
3Connecting an exit button
●Connect Green wire of exit button input to one wire between wires of exit button.
●Connect GND wire of power supply to the other wire.
4Connecting a door contact
●Connect COM terminal of door contact to Blue wire of door contact input.
●Connect NO terminal of door contact to GND (-) of power supply.
5Connecting a door lock depending on the lock type
●In a power fail safe, connect GND (-)wire of power supply to Yellow wire of door lock ty
pe input.
●In a power fail secure, put a floating state on Yellow wire of door lock type input.

Operation 9
p.13
1When power is supplied
1. All LEDs display red or green. Then they repeat on/off twice and become off.
2. As LED off, red LED turns on from the under to the top in order. And all LEDs turn red.
3. RFL200 / IP-RFL200’s buzzer sounds one time
2When registered key tag is read on RFL200 / IP-RFL20
0 or an exit button is pressed.
1. All LEDs turn from red to green. From the top to the under, they are off and on in order.
When all LEDs are on, they turn red.
2. At this time, the door is opened by definite time.
And the upper of two LEDs turn green. This means that open the door
3. RFL200 / IP-RFL200’s buzzer sounds one time.
3When unregistered key tag is read on RFL200 / IP-RFL
200

p.14When a master card is deleted or registered again
1. All LEDs turn red. Then they repeat on/off twice and become on.
2. RFL200 / IP-RFL200’s buzzer sounds twice.
4If key tag is approached by RFL200 / IP-RFL200 when t
he door is opened.
1. The upper of two LEDs still display green color. It means that open the door.
With the rest of LEDs, they indicate whether authentication or not (refer to 9.2 and 9.3).
5When a key tag is deleted or registered
1. If master card nears the product, buzzer sounds one time and the upper of 3 LEDs turn
green.
2. If a key tag that wish to register new is read by the product, buzzer sounds one time.
And the rests except the upper of 3 LEDs turn green. From the top to the under, they ar
e off in order. When all LEDs are off, LEDs turn red again. At this time, a key tag is regist
ered.
3. If a key tag is already registered, buzzer sounds twice.
The rests except the upper of 3 LEDs turn red. They repeat on/off twice and become on.
At this time, a key tag is deleted.
4. After finishing to register or delete a key tag, if reading a master card again, the upper
of 3
LEDs turn red with beeping one time. And all LEDs turn red.
Note: On the master mode, if user card isn’t read within 7 sec., the unit is automati
cally
on general mode.
6When a master card is deleted or registered again

Operationp.15
the lost or the change of a master card.
1. As power off, they make purple and blue wire close.
2. As power on, all LEDs turn red color with beeping twice.
Then they repeat twice and become on. At this time, a master card is deleted.
3. Upon deletion of Master Card, you will hear beep sound once and all LED indicators to
ggle between green and red twice and then turning off. In this condition; they turn red
from bottom up in sequence.
4. After finishing deleting a master card, turn off the power.
Connect again purple and blue wire to a device which has been connected basically.
5. As power on, RFL200 / IP-RFL200 operates normally.
At this time, a card which had been first read on RFL200 / IP-RFL200 is registered as a m
aster card. If you make already registered user card read, it will be deleted and then regi
stered as master card.
After registering a master card, the unit is automatically on master mode.
7When a product is initialized by using a master card
1. If master card is read on the unit, buzzer sounds one time, upper three LEDs change gr
een.
2. On master mode, if you make master card read again, upper green three LEDs flicker.
That means on initialization mode of product.
3. On initialization mode, if you make master card read again, the buzzer sounds four tim
es and all LEDs are changed to red and then Initialization starts.
4. If you make power on, RFL200 / IP-RFL200 operates normally.
At this time, registered card earlier on the RFL200 / IP-RFL200 is registered as master car
d.
 If user card is read on initialization mode of product, the unit is general mode.
User card isn’t registered or deleted.
 After registering a master card, the unit is automatically master mode.

p.16When a product is initialized by wiring the cable
8When a product is initialized by wiring the cable
1. As power off, make white, green and yellow wire are close.
2. As power on, all LEDs turn red or green color. After repeating on/off twice, they becom
e off.
3. As the LED off, only green LED turn on from the under to the top. All LEDs become gre
en.
4. RFL200 / IP-RFL200’s buzzer sounds four times. It indicates to complete initialization.
5. After finishing to initialize, connect again white, green and yellow wire to a device whic
h had been basically connected as power off.
6. If turn on power, RFL200 / IP-RFL200 operates normally.
At this time, a card which had been first read on RFL200 / IP-RFL200 is registered as a m
aster card.
After registering a master card, the unit is automatically master mode.

FCC REGISTRATION INFORMATION 10
p.17
FCC Requirements Part 15
Caution: Any changes or modifications in construction of this device which are not expressly
approved by the responsible for compliance could void the user's authority to operate the e
quipment.
NOTE: This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interface, and
2. This device must accept any interference received, including interference that may caus
e undesired operation.
This equipment has been tested and found to comply with the limits for a Class A Digital De
vice, pursuant to Part 15 of the FCC rules. These limits are designed to this equipment gener
ates, uses, and can radiate radio frequency energy and, if not installed and used in accordan
ce with the instructions, may cause harmful interference to radio communications.
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on another circuit.
4. Consult the dealer or an experienced radio/TV technician for help.