IDTECK Star 100R User manual

Quick Installation Guide
100R
IP100R

2
Quick Installation Guide
Table of Contents
1. SAFETY INFORMATION ............................................................................................. 3
2. IDENTIFYING SUPPLIED PARTS ................................................................................... 6
3. WALL MOUNT INSTALLATION ..................................................................................... 7
4. WIRE COLOR TABLE ................................................................................................ 9
5. WIEGAND OUTPUT FUNCTION ..................................................................................10
6. RECOMMENDED CABLE TYPE AND PERMISSIBLE LENGTH..................................................11
7. REVERSE DIODE CONNECTION ..................................................................................11
8. SYSTEM WIRING FOR TYPICAL APPLICATION .................................................................12
9. SYSTEM INITIALIZATION ..........................................................................................16
10. FCC REGISTRATION INFORMATION ...........................................................................18
11. ONLINE RMA POLICY & FREE SERVICE CRITERIA...........................................................19

3
Quick Installation Guide
1. SAFETY INFORMATION
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet. Using any other
adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock,
or damage to the product.
3. Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal
heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the controller, fasten it securely and firmly. The fall of controller may cause personal
injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with
water on top of the controller. Doing so may cause personal injury due to fire, electric shock, or falling
objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately
disconnect the power source and contact the service center. Continued use in such a condition may
cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center.
Never disassemble or modify this product in any way. (IDTECK is not liable for problems caused
by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or
electric shock.

4
Quick Installation Guide
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to
excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -30°C), or
high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then move or
reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause
fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the controller directly towards extremely bright objects such as sun.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
Continued on next page.

5
Quick Installation Guide
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong is provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.

6
Quick Installation Guide
2. IDENTIFYING SUPPLIED PARTS
Check all components in the gift box when purchasing.
Contact the vendor where you purchased the product if any components are missing.
Quick Guide (1copy)
Wall Mount (1ea)
Master Card (1ea)
Main Unit (1ea)
6.0x30mm
Anchor Bolt(4ea)
O-Ring (5ea)
3.5x40mm Screw (4ea)
3.5x12mm Screw (4ea)
10Pin Cable (1ea)
7Pin Cable (1ea)
3Pin Cable (1ea)
2Pin Cable (1ea)
Diode (2ea)

7
Quick Installation Guide
3. WALL MOUNT INSTALLATION
1. Use the provided template to drill two 6-32 holes and one 1/2" hole on the proper location of the wall
to mount the Wall Mount bracket as shown below.
2. Install wall mount to the wall using 2 screws.
3. Insert 5 O-rings to the wall mount as indicated, then route the cable of the main unit through the center
hole and push the main unit to wall mount to lock the main unit and make sure that the main unit is
locked with wall mount.
Continued on next page.

8
Quick Installation Guide
※CAUTION
1. Before mounting the 100R unit to the Wall Mount bracket, operational testing of the unit should be
completed, as the locking pins will lock the unit to the Wall Mount. Removing the unit from the Wall
Mount bracket after they have been installed together may cause damages to the bracket and render
its effectiveness.
2. When installing a reader on a metal plate.
The read range may get reduced if the reader is installed on a metal surface.
To prevent such a read range reduction, install standoffs between the metal surface and the reader.
3. When installing more than 2 readers side by side or back to back
The read range may get reduced if more than 2 readers are installed side by side or back to back.
Also, when a card is presented to one of the readers, the other reader may wrongly recognize the card
as well. To prevent such interference, make sure the distance between readers is at least 20cm.

9
Quick Installation Guide
4. WIRE COLOR TABLE
I/O PORT NAME
SIGNAL NAME
COLOR CODE
2-PIN
J1
Main Power (+12V)
DC +12V
Red
Power Ground
GND
Black
10-PIN
J2
Door Relay (NC)
NC (1)
Blue (White Stripe)
Door Relay (COM)
COM (1)
Gray (Red Stripe)
Door Relay (NO)
NO (1)
White (Red Stripe)
Alarm Relay (NC)
NC (2)
Purple (White Stripe)
Alarm Relay (COM)
COM (2)
White
Alarm Relay (NO)
NO (2)
Purple
Exit Button
EXIT
Orange
Door Sensor
CONTACT
Yellow (Red Stripe)
Aux Input 1
INPUT #1
Green
Aux Input 2
INPUT #2
Green (White Stripe)
7-PIN
J3
Wiegand Data 0
DATA 0
Pink
Wiegand Data 1
DATA 1
Cyan
TTL Output
TTL1 / D0
Orange (White Stripe)
Chime Bell Output
CHI / D1
Brown (White Stripe)
Aux Input 3
INPUT #3
Green (Red Stripe)
Reserved
N/A
Blue (Red Stripe)
Reserved
N/A
Yellow (White Stripe)
3-PIN
CON2
Ground
GND
Black
Reserved
N/A
Reserved
N/A

10
Quick Installation Guide
5. WIEGAND OUTPUT FUNCTION
The default output format of 100R/IP100R is TTL and Chime Bell output. But, you can configure the
100R/IP100R to generate output in Wiegand format and use it like a reader.
(The 100R/IP100R can output data from card reading, but can’t output data from keypad input.)
If you want to generate Wiegand instead of TTL output format, follow the table below.
Note: This function is only applicable to: 100R v6.00 or later / IP100R v3.00 or later.
SW1 #1
SW1 #2
SW2 #1
SW2 #2
Orange Cable
(White Stripe)
Brown Cable
(White Stripe)
ON
OFF
ON
OFF
TTL OUTPUT
Chime Bell Output
OFF
ON
OFF
ON
Wiegand Data 0 Out
Wiegand Data 1 Out
Note: When the Wiegand Output function is used, TTL Output wire is changed to Wiegand Data 0 and
Chime Bell Output wire to Wiegand Data 1 Output wire.
Therefore, you can’t use those functions. In addition, because TTL Output wire is changed to Wiegand
Data 0 Output, you can’t initialize the 100W/IP100W using the wires.
(You can use those functions again when setting SW1 and SW2 to the default state.)

11
Quick Installation Guide
6. RECOMMENDED CABLE TYPE AND PERMISSIBLE LENGTH
*: For readers, thicker wires are needed if you connect the reader with high current consumption.
7. REVERSE DIODE CONNECTION
If you connect the output device with coil (Door Locks or Alarm device) to the output relays, there will
be a high surge voltage created while the inductor is turning on and off. If you do not connect a reverse
diode, the surge voltage will transfer and damage the electronic circuit of the controller.
It is strongly recommended to add a reverse diode between the inductor coils to absorb this surge voltage.
Figure: Reverse Diode Connection
Reference
Description
Cable Specification
Maximum
Distance
1
100R series Power (DC12V)
DC Power-> 100R series
Belden #9409,18 AWG
2 conductor, unshielded
30m
*2
Reader(Power and Data)
External Reader
Belden #9512,22 AWG
4 conductor, shielded
150m
Belden #9514,22 AWG
8 conductor, shielded
3
Door Contact
Exit Button
Sensor Input
Input-> 100R series
Belden #9512,22 AWG
4 conductor, shielded
300m
Belden #9514,22 AWG
8 conductor, shielded
4
Door Lock
Alarm Device
Lock(Alarm)-> 100R Series
Belden #9409,18AWG
2 conductor, unshielded
300m

12
Quick Installation Guide
8. SYSTEM WIRING FOR TYPICAL APPLICATION

13
Quick Installation Guide
8.1 Power Connection
●Connect (+) wire of DC +12V power to Red wire.
●Connect Power GND (-) wire of DC +12V to Black wire.
8.2 Door Lock Connection
Connection of POWER FAIL SAFE: Door Lock
●Connect Door RELAY (COM), Grey with Red stripe wire to DC +12V
(be sure that the existing power supply has enough capacity to support this accessory or upgrade
to a sufficient one.)
●Connect (+) wire of Door Lock to Door RELAY (NC), Blue with White stripe wire.
●Connect (-) wire of Door Lock to Power GND (-) wire.
Connection of POWER FAIL SECURE: Door Lock
●Connect Door RELAY (COM), Grey with Red stripe wire to DC +12V
(be sure that the existing power supply has enough capacity to support this accessory or upgrade
to a sufficient one.)
●Connect (+) wire of Door Lock to Door RELAY (NO), White with Red stripe wire.
●Connect (-) wire of Door Lock to Power GND (-) wire.
8.3 Alarm Device Connection
●Connect Alarm RELAY (COM), White wire to DC +12V
(be sure that the existing power supply has enough capacity to support this accessory or upgrade
to a sufficient one.)
●Connect (+) wire of Alarm Device to Alarm RELAY (NO), Purple wire.
●Connect (-) wire of Alarm Device to Power GND (-) wire.

14
Quick Installation Guide
8.4 Exit Button Connection
●Connect one of the wires of Exit Button to Exit Button Input, Orange wire.
●Connect the other wire of Exit Button to Power GND (-) wire.
(If a normally closed Exit button is used, then see section 12-55 to change the detection
scheme from the defaulted setting)
8.5 Door Contact Sensor Connection
●Connect Door Contact sensor (COM) wire to Door Contact Input, Yellow with Red stripe wire.
●Connect Door Contact sensor (NO) wire to Power GND (-) wire.
(If a normally closed Door Contact sensor is used, then see section 12-57 to change the detection
scheme from the defaulted setting.)
8.6 Auxiliary Input Device Connection (Applied to AUX Input #1, #2, #3)
●Connect one wire of the Auxiliary Input Device to the AUX Input wire
(Input *1 Green, Input *2 Green with White stripe, Input *3 Green with Red stripe wire).
●Connect the other wire of Auxiliary Input Device to Power GND (-) wire.
(If a normally closed input device is used, then see section 12-49, 51 & 53 to change the
detection schemes from the defaulted settings.)
Continued on next page.

15
Quick Installation Guide
8.7 Auto-Dialer Connection (Separate purchase required)
The Auto-dialer function of this unit has not been evaluated by UL.
●Connect the input wire of Auto-Dialer to TTL output, Orange with White stripe wire.
●Connect (+) wire of Auto-Dialer to DC +12V (be sure that the existing power supply has enough
capacity to support this accessory or upgrade to a sufficient one.)
●Connect (-) wire of Auto-Dialer to Power GND (-) wire.
●Connect Telephone Line plug (RJ-14) to Auto-Dialer.
(If an active High Auto-Dialer is used, then see section 12-59 to change the TTL output
level from the defaulted setting.)
8.8 Wiegand Input Connection from Another Compatible Wiegand Reader
(Separate purchase required)
●Connect (+) wire of Reader to DC +12V (be sure that the existing power supply has enough capacity
to support this accessory or upgrade to a sufficient one.)
●Connect (-) wire of Reader to Power GND (-) wire.
●Connect Wiegand output DATA0 wire of the additional Reader to DATA0, Pink wire.
●Connect Wiegand output DATA1 wire of the additional Reader to DATA1, Cyan wire.
8.9 Chime Bell Connection (Separate purchase required)
●Connect (+) wire of Chime Bell unit to Bell Output, Brown with White stripe wire of Main
Unit.
●Connect(-) wire of Chime Bell unit to Power GND(-) wire.

16
Quick Installation Guide
9. SYSTEM INITIALIZATION
※WARNING: It will initialize all the values of the products to factory default.
9.1 Initialization using the command
9.2 Hardware Initialization (When the master card or ID is lost)
If you have lost the Configuration Card or if you forget the Master PIN number,
you may need to re-initialize.
the unit for new setup. There is a hard-wired Initialize function on the unit.
1) Open the top case taking out four bolts on the back.
2) As the left picture, make two jumpers short in state
of being on power
3) 3-color LED blinking with beep sound indicates
success of initialization
4) Turn off the power
5) Reinstall the Top case
1) Present a Master RF card close to the product
2) Press the ‘ENT’ button after pushing
the ‘9’ button twice
3) All data will be deleted after initialization

17
Quick Installation Guide
9.3 Wire Initialization
Execute initialization when you have lost master card.
100R: v5.0.4 or later / IP100R: v2.0.2 or later
1. Power off the device.
2. Connect the Green cable to Orange cable(White stripe) and then power up the device again.
3. After initialization is complete, it will emit beeps blinking three LEDs.
4. Use the device after disconnecting two cables.
100R: v5.0.0 - v5.0.3 / IP100R: v2.0.0 - v2.0.1
1. Power off the device.
2. Connect Orange cable to Orange cable(White stripe) and then power up the device again.
3. After initialization is complete, it will emit beeps blinking three LEDs.
4. Use the device after disconnecting two cables.
Orange

18
Quick Installation Guide
10. FCC REGISTRATION INFORMATION
FCC Requirements Part 15
CAUTION: Any changes or modifications in construction of this device which are not expressly approved
by the responsible for compliance could void the user's authority to operate the equipment.
NOTE: This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interface, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class A Digital Device, pursuant
to Part 15 of the FCC rules. These limits are designed to this equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the radio or television off and on, the user is encouraged to try to correct interference by one or
more of the following measures.
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on another circuit.
4. Consult the dealer or an experienced radio/TV technician for help.

19
Quick Installation Guide
11. ONLINE RMA POLICY & FREE SERVICE CRITERIA
Online RMA
Please check IDTECK RMA policy before requesting for A/S.
Online RMA (A/S) Policy
•RMA must be requested through online (WWW.IDTECK.COM).
•For RMA request, transaction history and return shipment information must be confirmed by
the service team.
•If S/N cannot be confirmed, RMA cannot take place.
•Please contact us via [e-mail] for inquiries about ONLINE RMA.
If there is no process being done after A/S request, it would most likely be if or when:
1. Serial number cannot be retrieved due to damage on the sticker.
2. QC Label is damaged.
3. The product was shipped without a proper RMA (A/S) process
4. The product requested for RMA is different than the one shipped to the RMA center.
5. The product was manufactured before the year 2005 (Except for the Lifetime warranty
product)
6. More than 2 years have passed after purchasing the S/W (IDTECK does not provide tech
support for any product without sales history).
•During warranty period, IDTECK will ONLY indemnify for defects that occurred during
the normal operation status.
•For defects created by consumer fault or incorrect operation of the product, service charge
may occur even during the warranty period. Also, additional charge may occur for product
replacement.
•All RMA products will be tested by IDTECK’s service team. If no problems were found after
conducting the test, additional service/repair fees will be charged.
(this applies for all IDTECK products).

20
Quick Installation Guide
Free A/S Service
1. Criteria
- Warranty period must be valid.
- When defects were created even though the product was handled correctly (Only during the
warranty period)
- If serious defect is found.
- All RMA products will be tested by IDTECK’s service team. If no problems were found after
conducting the test, additional service/repair fees (10 %) will be charged.
2. Base Date : Ship-out Date
3. RMA Service : Support Free Service
4. Period : Warranty period for IDTECK’s products is as below:
PRODUCT CATEGORY
WARRANTY
Long Range Reader
5 Years
Controller
2 Years
Standalone Controller
Biometric Reader
RF Reader (Non-Molded)
Application Software
RF Reader (Molded)
lifetime
RF Card (Passive Type)
RF Card (Active Type)
1 Year
Fingerprint Module/Sensor
Please check the box to agree with warranty and return policy.
Online RMA Request