IEI Technology Mustang-T100-T5 User manual

PCIe Accelerator Card with 8 Google Edge TPU, RoHS
Mustang-T100-T5
Quick Installation Guide
Version 1.0
June 28, 2021
Package List
Mustang-T100-T5 package includes the following items:
1 x Mustang-T100-T5 accelerator card
1 x Full height bracket
1 x QIG
©2021 Copyright by IEI Integration Corp.
All rights reserved.

1
Specifications
Main Chip: Five Google Coral Edge TPU Accelerator Modules
Operating Systems
oLinux: 64-bit version of Debian 10 or Ubuntu 16.04 (or newer),
and an x86-64 or ARMv8 system architecture
oWindows: 64-bit version of Windows 10, and x86-64 system
architecture
Dataplane Interface: PCI Express 2.0 x4
Power Consumption: Approximate 15W
Operating Temperature: -20°C~60°C
Cooling Solution: Active/Passive
Dimensions:
Standard half-height, half-length, single-slot PCIe card
DIP Switch/LED indicator: Identify card number
Support Framework: Tensorflow Lite
Precision: INT8
INT8 Performance
oUp to 20 TOPS, each TPU module up to 4 TOPS.
oFive TPU modules can provide 20 TOPS.
oRefer to Google Coral official website for more information
(https://coral.ai/docs/module/datasheet)
Supported Topology
oImage classification, Object detection, Image segmentation
oRefer to Google Coral official website for more information
(https://coral.ai/models)
Ordering Information
Mustang-T100-T5:
Computing accelerator card with five Google Coral edge TPU, PCIe
2.0 x4 interface, RoHS

2
Installation Procedure
--------------------------------------------------------------------------------------------------------------
WARNING! Disconnect the computer from the power supply to which you will install
the Mustang-T100-T5, or you risk damaging the system or experiencing electrical
shock.
--------------------------------------------------------------------------------------------------------------
1. Turn off the computer that you will install the Mustang-T100-T5, and remove the
power cord. Then, open the system chassis.
2. Locate an empty PCIe x4 slot. Remove the blank bracket panel that aligns with
the empty PCIe slot.
3. [Only needed for full-height installation]
Change the bracket on the Mustang-T100-T5
from low-profile bracket to full-height bracket
which is secured by two screws. NOTE: Before
changing the bracket, the metal enclosure must
be removed by removing the four retention
screws as shown on the right.
4. Align the Mustang-T100-T5 to the PCIe x4 slot. Press down gently, but firmly, to
seat the Mustang-T100-T5 correctly in the slot.
5. Secure the Mustang-T100-T5 to the system’s chassis with a retention screw.
6. Assign a card ID to the Mustang-T100-T5 by adjusting the rotary switch. The card
ID number assigned here will be shown on the LED display of the card after
power-up. See the diagram on the following page for the locations of the rotary
switch and the number LED.
NOTE: The LED digit only displays 0 through 7; if switched to 8, the LED will display
0; if switched to F, LED will display 7.

3
Connector Pinouts
FAN1: Fan Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
3
FAN_TACH
2
+12V
4
+3.3V_PWM
Board Layout: Jumper and Connector Locations (Unit: mm)
All the utilities for the Mustang-T100-T5
are available on IEI Resource Download
Center. Type the model name and press
Enter to find all the relevant utilities and
documentation. To install software from
the downloaded ISO file, mount the file
as a virtual drive to view its content.
IEI Resource Download Center
https://download.ieiworld.com