IGS OVERTAKE VR User manual

1
This Manual provides instructions for the installation, setup, use, maintenance and
repair of this product. The main purpose of this manual is to provide instructions for
operating the cabinet and safeguard personnel's safety during their operation so as to
guarantee correct operation of this product. Users must abide by all safety guidelines
and pay attention to warning labels to avoid injuries to personnel and damage to the
cabinet.
Non-technicians should not maintain or repair this product. Technicians refer to
personnel with a high school degree or above in mechanical engineering or electrical
engineering, or workers equipped with similar working skills and engage in the
maintenance, management and repair of game cabinets on a daily basis.
Keep this manual for your future references. Moreover, when assigning others to move,
install, maintain and repair the cabinet, all store owners should first read the related
content stated in this manual, and instruct related personnel to follow corresponding
rules.
Disclaimer
IGS does not warrant the correctness and completeness of this manual either in direct
or indirect ways, nor does it warrant the commercial or general applications for specific
purposes. IGS reserves the right to modify or change this manual and no prior notice
will be given.
Trademarks
IGS® is the registered trademark of International Games System Co., Ltd.
© Copyright owned 2018, International Games System Co., Ltd.
Without prior written permission, copying any content of this manual in any format is
prohibited.
All trademarks and business identity icons used in this document are the property of
their legal owners.
About This Manual

2
Ordinary
Without the permission from our designated personnel, do not dissemble,
change or remodel our products.
Be sure to operate this product according to the instructions of this manual.
Any inappropriate operation would damage this product and threaten the
personal safety of players as well as onlookers.
Routinely check, maintain and repair this product.
Keep each warning label on this product clean in order to make sure the
descriptions are readable. If the filthiness on the label could not be got rid of
or descriptions are indistinct, immediately replace the labels.
Installed locations
This cabinet is designed for indoor use, so do not place it outdoors or in the
following locations:
Places under direct sunlight, are leaking, moist or of high temperature.
Places near flammable, highly volatile or dangerous objects.
Places where the surface is tilted, unstable or frequently shaking.
Places close to emergency exits, fire extinguishers or any other
extinguishing equipment.
The vent located in the bottom of this product is for the cabinet and monitor to
emit warm air, so do not place any item close to the vent, or malfunction
might occur.
A distance of 30 cm or more should be kept between the cabinet and walls,
another cabinet or the hallway.
Safety Precautions
Caution
Caution

3
Power
Before plugging in the cabinet, first make sure the voltage is as require
（ 110V or 220V ） , or fires and electric shocks might occur.
When plugging in the cabinet, use an outlet with ground wire.
Do not expose electrical cords and ground wires on the hallway, or damage,
electric shocks and short circuit might occur.
Do not place flammable items near electrical cords to avoid fires.
If electrical cords are to be damaged, replace new ones with your local
distributor.
To avoid electric shocks or short circuits:
Before repair or maintenance, power must be turned off.
Do not touch plugs with wet hands.
Do not immediately unplug or plug in the cabinet.
When unplugging the electric cord, tightly hold the plug and avoid
pulling the electric cord.
Transporting
When transporting this product with a forklift, make sure to exert the force
point to avoid accidents or damage to the cabinet.
When moving this product with a vehicle, make sure to fasten the caster
rather than the tail to prevent shaking, or damage might occur the cabinet.
The LCD monitor of the cabinet is rather fragile, and should be prevented
from severe shaking or being hit by outside forces.
Caution
Caution

4
Moving
Before moving the cabinet, first unplug it to avoid accidents.
When moving the cabinet, pay attention to the obstacles ahead and check if
the surface of the ground is flat to avoid accidents and damage to the cabinet.
When moving the cabinet, at least two personnel should work together to
avoid accidents and injuries.
During the play
To prevent customers from being injured or encountering accidents, people
apply to the following categories should avoid using this product:
People with unsatisfactory health conditions such as patients of
hypertension or heart disease.
People with injuries or are physically disabled.
People wearing slippery shoes or high heels.
People who are unable to step on the pedal when sitting.
People who are pregnant, drunk or would easily feel dizzy.
Children who are below the age of 13.
If customers feel uncomfortable during their play, remind them to pause or
discontinue the play.
Remind customers to carefully read the warning labels as well as other
reminding descriptions, and operate according to instructions to avoid electric
shocks or short circuits, etc.
Caution
Caution

5
About This Manual
Safety Precautions
1 VR Instruction Manual
1.1 Important Notes about Cabinet
Installation
1.2 Important Notes about Turning
the Machine On/Off
1.3 Quick installation
1.3.1 Connection settings
1.3.2 I/O Adjustment
1.3.3 Setting other related
items
1.4 VR Headset Calibration and
Wearing Instructions
1.5 Important Notes for Staff
2 Game Description
2.1 Game introduction
2.2 Distinctive plays
2.3 Game control
2.4 Instruction of the game display
3 Operator Settings
3.1 Framework of the menu
3.2 Main Menu Operation
3.3 Hardware test
3.3.1 VR device status
3.3.2 Connection test
3.3.3 I/O test
3.3.4 Force feedback test
3.3.5 Lamp test
3.3.6 Screen test
3.3.7 Speaker test
3.3.8 Vibration seat test
3.3.9 Counter test
3.3.10 Air spring test
3.3.11 Fan speed test
3.3.12 Drain valve test
3.4 System settings
3.4.1 Time settings
3.4.2 Connection Settings
3.4.3 I/O adjustment
3.4.4 Country
3.4.5 Password setting
3.4.6 Air spring adjustment
3.4.7 Seatbelt setting
3.4.8 Height sensor modify
3.4.9 Fan mode setting
3.5 Game settings
3.5.1 Charge mode setting
3.5.2 Volume setting
3.5.3 Headset calibration
settings
3.5.4 Game Display Setting
3.5.5 Track Length setting
3.5.6 Steering wheel teaching
setting
3.5.7 Assistant costume
setting
3.6 Income data
3.6.1 Daily income
3.6.2 Monthly income
3.6.3 Total income
3.7 System reset
3.7.1 Income Data Reset
3.7.2 System reset
3.7.3 Ranking Board Reset
3.8 Game setting defaults
Table of Contents

6
1.1 Important Notes about Cabinet Installation
After purchasing the product, please move the cabinet to the location where it will
be used before connecting any wires. Please follow the instructions below during
installation.
In order to ensure that each cabinet operates normally, please line up the
cabinets side-by-side or position them by facing the screens radially outward.
In addition, the distance of the VR lamp post lights between cabinets must be
at least 100 cm.
1、
、、
、VR Instruction Manual

7
To prevent interference between cabinets which may cause problems for the
base station to detect the VR headset properly, when placing cabinets, please
do not position them with front/rear gaps and do not place the cabinets with
their screens facing radially inward.

8
To prevent interference from bright lights which may cause problems for the
base station to detect the VR headset properly, please keep the cabinet away
from sunlight exposure and do not install high-intensity light sources such as
spotlights, searchlights, or halogen lamps too closely above the cabinet to
prevent direct light exposure from these light sources.
To prevent interference between two <OVERTAKE VR> cabinets, please do
not face other base station models toward the cabinet. The base station of
other VR products should be at least 5m away from the cabinet of
<OVERTAKE VR>.

9
To facilitate the smooth operation of the VR headset's calibration process,
please fasten the cabinet with the tail before turning on the machine:
Counterclockwise turn the tail till a distance of at least 5 mm is kept between
the caster and the floor.

10
1.2 Important Notes about Turning the Machine On/Off
Turning On the Machine
To facilitate the smooth operation of the motion platform as well as the VR
headset's calibration process, please follow the steps below to turn on the
cabinet:
Use the key to open the storage door behind the seat and take out the VR
headset.
Turn in the clockwise direction to tighten the strap on the VR headset.
Place the VR headset horizontally inside the headset stand in front of the
steering wheel.

11
Switch on the power on the back of the machine.
Note: During machine startup, if the screen shows 【
【【
【HMD Detecting】
】】
】in
red letters, please pick up the VR headset from the headset stand
and shake it gently. Once the screen shows 【
【【
【Keep press
Calibrate View to continue】
】】
】in red letters, place the VR headset
back into the headset stand, then press and hold the 【
【【
【Calibrate
View】
】】
】button on either side of the cabinet until the VR headset
calibration process is completed. If the steps listed above are
ineffective, please restart the machine.
Note: During machine startup, if the screen shows 【
【【
【Emergency button
has been activated】
】】
】in red letters, please press the 【
【【
【Emergency
Stop】
】】
】button again next to the headset stand to cancel the
Emergency Stop function and complete the motion platform
calibration process.
Turning Off the Machine

12
Please ensure that the game is in idle status and no player is sitting on the
cabinet.
Shut off the power on the back of the machine.
Use the key to open the storage door behind the seat and carefully place
the VR headset back in storage.

13
1.3 Quick Installation
1.3.1 Connection settings
You can enter 【
【【
【Connection settings】
】】
】to set up the group number and ID of
the cabinet.
Enter 【
【【
【Operator settings】
】】
】→【
【【
【2.System settings】
】】
】→【
【【
【2-2.Connection
settings】
】】
】, and appoint all cabinets in connection into the same group, but
provide each cabinet a different ID.
Note: The connection ID of cabinets suggested from left to right in
sequence: 1P, 2P, 3P, 4P.
1.3.2 I/O Adjustment
Enter 【
【【
【Operator settings】
】】
】→【
【【
【2.System settings】
】】
】→【
【【
【2-3.I/O
Adjustment】
】】
】to run adjustment.
After selecting 【
【【
【I/O Adjustment】
】】
】, it will be adjusted from top to bottom in
the following order: turn the steering wheel to the left end, center the
steering wheel, turn the steering wheel to the right end, release the
throttle, step on the throttle, release the brake and step on the brake.
1.3.3 Setting other related items
Setting other related items (recommended):
Enter 【
【【
【Operator settings】
】】
】→【
【【
【2.System settings】
】】
】→【
【【
【2-1Time
settings】
】】
】,and set the cabinets to be connected to be the same time.
Enter 【
【【
【Operator settings】
】】
】→【
【【
【2.System settings】
】】
】→【
【【
【2-4Country】
】】
】

14
to set up the location and name of the store.
Enter 【
【【
【Operator settings】
】】
】→【
【【
【3.Game settings】
】】
】→【
【【
【3-2.Volume
setting】
】】
】, to set up 【
【【
【3-2-1.Daytime volume setting】
】】
】 and
【
【【
【3-2-2.Evening volume setting】
】】
】.
..
.

15
1.4 VR Headset Calibration and Wearing Instructions
If the screen of the VR headset during play is too different from the correct
screen, perform a manual calibration procedure to adjust the VR headset.
Note: If the message 【
【【
【Please ask the staff to calibrate the VR device】
】】
】is
displayed on the screen or if the 【
【【
【VR headset icon shown on the
upper-right corner of the screen is gray for an extended period of time】
】】
】,
please perform a manual calibration for the VR headset.
Correct screen (Tutorial) Error screen (Tutorial)
Correct screen (Racing) Error screen (Racing)
Manual calibration procedures for the VR headset are listed below:
While the game is in progress, press the 【
【【
【Emergency stop】
】】
】button and
then remove the VR headset.
After verifying that the VR headset icon shown in the upper-right corner of
the screen is green (detection successful), place the VR headset
horizontally inside the headset stand.
Press and hold the 【
【【
【Calibrate View】
】】
】 button located on the right or left
side of the cabinet for 2 seconds.
Wait until the calibration timer counts down and "OK" is displayed on the
screen.

16
Manual calibration for the VR headset is now complete.
Note: If the VR headset icon displayed on the screen's upper-right corner
is shown in gray (detection failed), please pick up the VR headset
from the headset stand and shake it gently until the VR headset
icon becomes green (detection successful).
Detection Failed
Detection Successful

17
Instructions for wearing the VR headset:
Turn the knob on the back of the VR headset in the counterclockwise
direction to loosen the head strap.
Hold the VR headset on both sides and place it over the player's eyes,
allowing the VR headset to surround the player's eyes.
Note: If a player wears glasses, it is recommended that the player
continue to wear them while playing. If the player's glasses frame is
too wide, the eyeglasses can be inserted into the VR headset from
the side first, then the VR headset as well as the glasses can be
worn by the player at the same time.

18
Pull down the head strap on the back and turn the knob in the clockwise
direction to tighten the head strap for a comfortable fit.
Note: The knob must be tightened so that the VR headset will not shake
when the player moves his/her head; however, do not make it too
tight as it will cause discomfort around the player's eyes.
If the player's head is too large/small, the Velcro strap on top can be
opened up to adjust the length of the upper head strap so that the back
strap can be adjusted to wrap around the back of the player's head.

19
Once the player has worn the VR headset, press down lightly on the
earphones so they are closer to the player's ears. The height of the
earphones can also be adjusted to match the player's ear position.

20
1.5 Important Notes for Staff
In order to maintain the VR headset's view position in a normal operating
condition, please do not place the VR headset in an area where it cannot be
detected by the base station, such as: on the seat and outside of the cabinet.