Impex COMPETITOR CB-180 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
CB-180
Retain This
Manual for
Reference
06-13-06
OWNER'S
MANUAL
COMPETITOR
WEIGHT BENCH
CB-180
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................…. 1
IMPORTANT SAFETY NOTICES..................................................................…. 2
HARDWARE IDENTIFIER.....…....................................................................…. 4
ASSEMBLY INSTRUCTIONS........................................................................…. 5
EXPLODED DIAGRAM……………………………………………………………… 9
PARTS LIST...............................................................................................……. 10
WARRANTY.................................................................................................….. 11
ORDERING PARTS.......................................................................................… 11
BEFORE YOU BEGIN
Thank you for selecting the COMPETITOR CB-180 Weight Bench by
IMPEX INC. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there
are missing or damaged parts, we guarantee you complete satisfaction
through direct assistance from our factory. To avoid unnecessary delays,
please call our TOLL-FREE customer service number. Our Customer
Service Agents will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]m

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire
manual before you assemble or operate your machine. In particular, note the following
safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave
children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near
water or outdoors.
5. Keep hands and feet away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or
other clothing that could become caught in the machine. Running or aerobic shoes
are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician
in attendance.
10. Before using the machine to exercise, always do stretching exercises to properly
warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Maximum user’s weight capacity 200 lbs.
14. Maximum weight capacity on Leg Developer 80 lbs.
15. Maximum weight capacity on Uprights 200 lbs.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS. 2

WARNING LABEL REPLACEMENT
The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible,
please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
3

HARDWARE PACK
4

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine
to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Left & Right Upright Beams (#1 & 2) onto the Lower Upright Beams (#3).
B.) Connect the Left & Right Upright Beams by a Cross Brace (#4) in the Mid-span.
Secure them with two M8 x 2 1/8” Hex Bolts (#18), one Bracket (#16), four ∅5/8”
Washers (#24), and two M8 Aircraft Nuts (#26) on each end of the Cross Brace.
C.)Place the Backrest Adjustment Bar (#13) onto selected slot on the Upright Beams
to obtain desired incline of Backrest. DIAGRAM 1
5

STEP 2 (See Diagram 2)
A.) Insert the Main Support Frame (#5) into the Seat Support Frame (#6). Secure them
with two M8 x 2 1/8” Hex Bolts (#18), two Brackets (#16), four Ø 5/8” Washers (#24),
and two M8 Aircraft Nuts (#26).
B.) Attach the Main Support Frame (#5) to the Cross Brace (#4). Secure it with two M8 X
2 1/8” Hex Bolts (#18), one Bracket (#16), four Ø 5/8” Washers (#24), and two M8
Aircraft Nuts (#26).
C.)Attach the Seat Support Frame (#6) to the Leg Developer Holder (#7). Secure it with
two M8 x 2 1/8” Hex Bolts (#18), one Bracket (#16), four Ø 5/8” Washers (#24), and
two M8 Aircraft Nuts (#26).
D.)Place the Seat Pad (#12) onto the Seat Support Frame (#6). Secure it with two M6 x
5/8” Hex Bolts (#21) and two Ø ½” Washers (#25).
DIAGRAM 2
6

STEP 3 (See Diagram 3)
A.) Insert the two Upper Backrest Supports (#8) into two Lower Backrest Supports (#9).
Secure them with two M6 x 1 3/8” Hex Bolts (#20), four Ø ½” Washers (#25), and
two M6 Aircraft Nuts (#28).
B.) Attach the side-holes on the Lower Backrest Supports (#9) to each end of the pivot
on the Seat Support Frame (#6). Align the holes and insert a M10 x 6 7/8” Axle
(#17) through the holes. Secure it with two Ø ¾” Washers (#23) and M10 Aircraft
Nuts (#27). Do not over tighten the Nuts. Make sure the Backrest Supports are
able to swivel.
C.)Place the Lower Backrest Board (#10) onto the Backrest Supports. Secure it with
four M6 x 1 3/8” Hex Bolts (#20) and Ø ½” Washers (#25).
D.)Place the Upper Backrest Board (#11) onto the Backrest Supports. Secure it with
two M6 x 1 3/8” Hex Bolts (#20) and Ø ½” Washers (#25).
DIAGRAM 3
7

STEP 4 (See Diagram 4)
A.) Attach the Leg Developer (#29) to the Leg Developer Holder (#7). Secure it with one
M10 x 2 1/8” Hex Bolt (#19), two Ø ¾” Washers (#23), and one M10 Aircraft Nut (#27).
Do not over tighten the Nut and Bolt. Make sure the Leg Developer is able to swivel.
B.) Insert the Weight Post (#31) into the Leg Developer. Secure it with one M8 x 1 ¾” Hex
Bolt (#22), two Ø 5/8” Washers (#24), and one M8 Aircraft Nut (#26).
C.)Insert the Foam Tube (#30) halfway through the holes on the Leg Developer. Attach two
Foam Rolls (#32) onto the Tube from both ends. DIAGRAM 4
8

9