Impex MP-LVR User manual

MARCY®PLATINUM
LEVERAGE BENCH
MP-LVR
IMPEX®INC.
14777 Don Julian Rd., City of Industry, CA 91746
Tel: [phone] Fax [phone]
www.impex-fitness.com
[email protected]
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
MP-LVR
Retain This
Manual for
Reference
07/12/07
OWNER'S
MANUAL

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICE....................................................................... 2
HARDWARE PACK………............................................................................... 4
ASSEMBLY INSTRUCTIONS........................................................................... 8
EXPLODED DIAGRAM.................................................................................... 16
PARTS LIST..................................................................................................... 18
WARRANTY..................................................................................................... 19
ORDERING PARTS.......................................................................................... 19
BEFORE YOU BEGIN
Thank you for selecting the MARCY PLATINUM MP-LVR Leverage Bench by
IMPEX®INC. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee you complete satisfaction through
direct assistance from our factory. To avoid unnecessary delays, please
call our TOLL-FREE customer service number. Our Customer Service
Agents will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave children
unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water or
outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or other
clothing that could become caught in the machine. Running or aerobic shoes are also
required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Maximum user’s weight: 300 lbs.
14. Maximum weight on High Pulley: 100 lbs.
15. Maximum weight on Low Pulley: 100 lbs.
16. Maximum weight on Press Arms: 300 lbs. (150 lbs for each Press Arm).
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

WARNING LABEL REPLACEMENT
The Warning Labels shown here have been placed on the Rear Stabilizer and Lat Bar. If the
labels are missing or illegible, please call customer service at 1-800-999-8899 for
replacement. Apply the labels in location shown.
3

HARDWARE PACK
4

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
6

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
7

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended two or more people assembling this
machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten all Nuts and Bolts installed until instructed to do so.
B.) Attach the Middle Support Frame (#11) to the Front Support Frame (#6). Secure them
together with two M10 x 2 ½” Carriage Bolts (#56), one 4 ¾” x 2 ¾” Bracket (#21), two Ø
¾” Washers (#70), and two M10 Aircraft Nuts (#75).
C.)Attach the Leverage Rear Stabilizer (#12) to the Middle Support Frame. Secure them with
two M10 x 2 ½” Carriage Bolts (#56), one 4 ¾” x 2” Bracket (#20), two Ø ¾” Washers
(#70), and two M10 Aircraft Nuts (#75).
D.)Attach the Diagonal Support (#18) to the Front Support Frame (#6) and Middle Support
Frame (#11). Secure each end of Diagonal Support with one M10 x 5/8” Allen Bolt (#64)
and Ø ¾” Washer (#70).
E.) Insert the Lat Bar Frame Insert (#14) halfway into the opening on the Front Support
Frame (#6). Attach two Double Brackets (#19) to the top holes on the Front Support
Frame (#6). Align the holes and secure it with one M10 x 2 ½” Carriage Bolt (#56), one
M10 x 3 3/8” Carriage Bolt (#57), two Ø ¾” Washers (#70) and two M10 Aircraft Nuts
(#75).
F.) Slide the Lat Bar Frame (#7) onto the upper half of the Lat Bar Frame Insert (#14). Align
the upper holes on the Double Brackets (#19) to the holes on the Lat Bar Frame (#7).
Secure it with one M10 x 2 ½” Carriage Bolt (#56), one M10 x 3 3/8” Carriage Bolt (#57),
two Ø ¾” Washers (#70) and two M10 Aircraft Nuts (#75).
G.)Securely tighten all Nuts and Bolts previously installed.
H.)Insert a Weight Post (#13) into the hole on the Leverage Rear Stabilizer (#12). Secure it
with one M10 x 1” Allen Bolt (#62) and Ø3/4” Washer (#70). Attach an Olympic Sleeve
(#27) onto the Weight Post. Attach a Spring Clip (#31) onto the Sleeve. Repeat the same
procedure to install the other side.
I.) Attach the Foot Plate (#17) to the pivot on the Front Support Frame (#6). Secure it with
one M10 x 4 ¾” Allen Bolt (#61) and Ø ¾” Washer (#70) from each side.
8

9