Impex MD-823 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MD-823
Retain This
Manual for
Reference
100915
OWNER'S
MANUAL
MARCY DIAMOND
OLYMPIC BENCH
MD-823
IMPEX®INC.
2801 S. Towne Ave., Pomona, CA 91766
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN....................................................................................……….. 1
IMPORTANT SAFETY NOTICE...................................................................……….. 2
HARDWARE PACK……….....….....................................................................……….. 4
ASSEMBLY INSTRUCTIONS.........................................................................……….. 7
EXPLODED DIAGRAM…………………………………………………………………….. 12
PARTS LIST………….………….......................................................................………. 13
WARRANTY.................................................................................................…………. 14
ORDERING PARTS.......................................................................................………… 14
BEFORE YOU BEGIN
Thank you for selecting the MARCY DIAMOND MD-823 Olympic Bench by
IMPEX INC. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee you complete satisfaction through
direct assistance from our factory. To avoid unnecessary delays, please
call our TOLL-FREE customer service number. Our Customer Service
Agents will provide immediate assistance to you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. – Fri. 9 a.m. – 5 p.m. PST
www.impex-fitness.com
[email protected]
1

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Maximum user’s weight: 300 lbs.
14. Maximum weight on uprights: 300 lbs.
15. Maximum weight on leg developer: 100 lbs.
16. Maximum weight on weight post: 100 lbs.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

WARNING LABEL PLACEMENT
The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible,
please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown
3

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
6

ASSEMBLY INSTRUCTION
Tools required for assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended that two or more people assemble this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Attach the Left Upright Beam (#1) to a Rear Base Frame (#14). Secure it with one M10 x 4 ½”
Allen Bolt (#62), one Ø ¾” Washer (#70), and one M10 Aircraft Nut (#68).
C.)Attach Left Diagonal Support (#15) to Left Upright Beam and the Rear Base. Secure each end
with one M10 x 3” Allen Bolt (#60), two Ø ¾” Washers (#70), and one M10 Aircraft Nut (#68).
D.)Repeat B & C above to install Right Upright Beam (#2), Right Diagonal Support (#16), and the
other Rear Base together.
E.) Connect the Left and Right Upright Beams with a Cross Brace (#3) in the mid-span. Secure
each end with two M10 x 4 ¾” Carriage Bolts (#66), one 4 ¾” x 2” Bracket (#26), two Ø ¾”
Washers (#70), and two M10 Aircraft Nuts (#68). DIAGRAM 1
7

STEP 2 (See Diagram 2)
A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Attach the Leg developer Holder (#5) to the Front Base (#10). Secure it with two M10 x
5/8”Allen Bolts (#56) and two Ø ¾” Washers (#70). Thread a Lock Knob (#51) into the Leg
Developer Holder.
C.)Slide the Sliding Block (#6) onto the Main Seat Support (#4). Thread a Lock Knob into the
selected hole to hold the Sliding Block in position.
D.)Attach the Main Seat Support to the Leg Developer Holder. Secure it from top with one
M10 x 5/8” Allen Bolt (#56) and one Ø ¾” Washer (#70). Secure it with side with one M10 x
2 ½” Allen Bolt (#59), two Ø ¾” Washers (#70), and one M10 Aircraft Nut (#68).
E.) Attach the Main Seat Support to the Cross Brace (#3). Secure it from the rear with two M10
x 2 3/8” Carriage Bolts (#64), one 4 ¾” x 2” Bracket (#26), two ¾” Washers (#70), and
two M10 Aircraft Nuts (#68). Secure it from the top with one M10 x 3 1/8” Carriage Bolt
(#65), one Ø ¾” Washer (#70), and one M10 Aircraft Nut (#68).
F.) Securely tighten all Nuts and Bolts in Step-1 & Step-2. DIAGRAM 2
8

STEP 3 (See Diagram 3)
A.) Place the Backrest Adjustment Bar (#7) onto the selected slots on the Left & Right
Upright Beam (#1 & #2).
B.) Attach the pivot on Seat Incline Support (#12) into the side holes on the two Seat
Supports (#11). Place the other end of Seat Incline Support to the open slot on Sliding
Block (#6).
C.) Attach the brackets at the end of the two Seat Supports to the pivot on the Sliding Block
(#6). Attach the bottom side holes on the two Backrest Supports (#13) to the brackets on
Seat Supports. Align the holes. Secure them together with one M10 x 6 1/8” Allen Bolt
(#63), two Ø ¾” Washers (#70), and one M10 Aircraft Nut (#68). Do over tighten the Nut
and Bolt. Make sure the Seat Supports and Backrest Supports are able to move
freely. Place the other end of Backrest Board rest against the Backrest Adjustment Bar.
D.) Use the Backrest Adjustment Bar and Seat Incline Support to adjust the incline of Seat
and Backrest.
E.) Attach a Weight Post (#24) to Left & Right Diagonal Support (#15 & #16). Secure each
Post with one M10 x ¾” Allen Bolt (#57) and one Ø ¾” Washer (#70). DIAGRAM 3
9