Impex MARCY SB-670 User manual

MARCY®
Multi Purpose Bench
SB-670
IMPEX®Inc.
14777 DON JULIAN RD.,
CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[e-mail]
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
SB-670
Retain This
Manual for
Reference
07/23/09
OWNER'S
MANUAL

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICE....................................................................... 2
HARDWARE PACK………............................................................................... 4
ASSEMBLY INSTRUCTIONS........................................................................... 5
EXPLODED DIAGRAM.................................................................................... 8
PARTS LIST..................................................................................................... 9
WARRANTY..................................................................................................... 10
ORDERING PARTS.......................................................................................... 10
BEFORE YOU BEGIN
Thank you for selecting the MARCY MULTI PURPOSE BENCH SB-670 by
IMEX INC. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee your complete satisfaction
through direct assistance from our factory. To avoid unnecessary delays,
please call our TOLL-FREE customer service number. Our Customer
Service Agents will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]m

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave children
unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water or
outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or other
clothing that could become caught in the machine. Running or aerobic shoes are also
required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Maximum user’s weight: 300 lbs.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF
THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

WARNING LABEL PLACEMENT
The Warning Label shown here has been placed on the Rear Stabilizer. If the label is
missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply
the label in location shown
3

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4

ASSEMBLY INSTRUCTION
Tools Required For Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended for two or more people to assemble this
machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Attach the Front Post (#4) to the Front Stabilizer (#3). Secure it with three M10 x 5/8” Allen
Bolts (#23) and three Ø ¾” Washers (#31).
C.) Attach the Main Seat Support (#1) to Front Post. Secure the lower hole with one M10 x 4 ¾”
Allen Bolt (#21), two Ø ¾” Washers (#31), and one M10 Aircraft Nuts (#29). Secure the
upper hole with a Lock Pin (#11) into the upper hole.
D.) Attach the Main Seat Support to the Rear Stabilizer (#2). Secure it with three M10 x 5/8”
Allen Bolts (#23) and three Ø ¾” Washers (#31).
E.) Securely tighten all nuts and bolts.
F.) Attach the Handle (#12) to the Front Post. Secure it with two M6 x 5/8” Allen Bolts (#13).
G.) Fold the Font Post by pulling out the Lock Pin (#11), fold down the Front Post, and then
reinsert the Lock Pin.
DIAGRAM 1
5

STEP 2 (See Diagram 2)
A.) Attach the two Ø 5/8” x Ø 1” Bushings (#19) to the holes on the open bracket on the Main
Seat Support (#1). Attach the Left & and Right Seat Bracket (#5 & #6) to the open bracket.
Attach the pivot on the Backrest Support (#7) inside the opening.
B.) Align the holes. Secure them together with one Axle (#10), two Ø ¾” Washers (#31), and
two M10 Aircraft Nuts (#29). Do not over tighten the Nuts. Make sure the Backrest
Support can swivel freely.
C.) Remove the T-shaped head from the T-shaped Pull Pin (#9). Remove the Nut from the Pull
Pin.
D.) Insert the Spring and the Pull Pin through the open slot on Left Seat Bracket (#5) and
through the pivot on Main Seat Support. Thread back the Nut to the Pull Pin, push the Pull
Pin through theopen slot on the Right Seat Bracket (#6). Thread the T-shaped head back to
the PullPin. Pull the T-shaped PullPin, and then adjust the Seat bracket to desired position,
and then release the Pull Pin to lock the Seat Brackets in position.
E.) Attach the pivot on the Incline Support (#8) to the open bracket on the back of Backrest
Support. Secure it with one M12 x3” Allen Bolt (#22), two Ø 1” Washers (#30), and one M12
Aircraft Nut (#28). Do not over tighten the Nut and Bolt. Make sure the Incline Support
can swivel freely. DIAGRAM 2
6

STEP 3 (See Diagram 3)
A.) Attach the Seat Pad to the Left & Right Seat Bracket (#5 & #6). Secure them with four M6 x
¾” Allen Bolts (#25) and four Ø ½” Washers (#33).
B.) Attach the Backrest Board to the Backrest Support (#7). Secure it with two M8 x 1 ¾” Allen
Bolts (#26) and two Ø 5/8” Washers (#32).
C.) Use the handle on Incline Support (#8) to move the Incline Support to selected open slot on
Main Seat Support (#1) to obtain the desired Backrest Incline. DIAGRAM 3
7

EXPLODED DIAGRAM
8

PARTS LIST
KEY NO. DESCRIPTION QUANTITY
1 Main Seat Support 1
2 Rear Stabilizer 1
3 Front Stabilizer 1
4 Front Post 1
5 Left Seat Bracket 1
6 Right Seat Bracket 1
7 Backrest Support 1
8 Incline Support 1
9 T-shaped Pull Pin 1
10 Axle 1
11 Lock Pin 1
12 Handle 1
13 M6 x 5/8” Allen Bolt 2
14 Ø 1 ¼” x ¾” End Cap 1
15 Grip 1
16 Seat Pad 1
17 Backrest Board 1
18 Panel 1
19 Ø 5/8” x Ø 1” Bushing 2
20 2 3/8”x 1 1/8” End Cap 1
21 M10 x 4 ¾” Allen Bolt 1
22 M12 x 3” Allen Bolt 1
23 M10 x 5/8” Allen Bolt 6
24 M5 x ¼” Allen Bolt 1
25 M6 x ¾” Allen Bolt 4
26 M8 x 1 ¾” Allen Bolt 4
27 M8 x 5/8” Allen Bolt 3
28 M12 Aircraft Nut 1
29 M10 Aircraft Nut 3
30 Ø 1” Washer 2
31 Ø ¾” Washer 10
32 Ø 5/8” Washer 13
33 Ø ½” Washer 4
34 #8 Allen Wrench (Tool) 1
35 #6 Allen Wrench (Tool) 1
36 #5 Allen Wrench (Tool) 1
37 #3 Allen Wrench (Tool) 1
38 Ø 1” x Ø ½” Bushing 2
39 Ø 1” x Ø 5/8” Bushing 2
40 Wheel 2
41 M8 Aircraft Nut 2
9