Impex COMPETITOR CB-280 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
CB-280
Retain This
Manual for
Reference
07-1704
OWNER'S
MANUAL
COMPETITOR BENCH
CB-280
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................…. 1
IMPORTANT SAFETY NOTICES..................................................................…. 2
HARDWARE PACK……….....…....................................................................…. 3
ASSEMBLY INSTRUCTIONS........................................................................…. 4
EXPLODED DIAGRAM………………………………………………………………. 10
PARTS LIST...............................................................................................……. 11
WARRANTY.................................…..............................................................…. 12
ORDERING PARTS.......................…..............................................................… 12
BEFORE YOU BEGIN
Thank you for selecting the COMPETITOR CB-280 Weight Bench by IMPEX
FITNESS PRODUCTS. For your safety and benefit, read this manual
carefully before using the machine. As a manufacturer, we are committed
to provide you complete customer satisfaction. If you have any questions, or
find there are missing or damaged parts, we guarantee you complete
satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOLL-FREE customer service number.
Our Customer Service Agents will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]m

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave
children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water
or outdoors.
5. Keep hands and feet away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or
other clothing that could become caught in the machine. Running or aerobic shoes are
also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm
up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

HARDWARE PACK
3

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#2) in the Mid-span.
Secure them with two M8 x 2 ½” Carriage Bolts (#20), one Bracket (#10), two ∅5/8”
Washers (#26), and two M8 Aircraft Nuts (#24) on each end of the Cross Brace.
B.) Insert the Backrest Adjustment Bar (#11) through a selected hole to obtain desired
incline of Backrest. DIAGRAM 1
4

STEP 2 (See Diagram 2)
A.) Attach the Main Seat Support (#3) to the Cross Brace (#2). Secure it with four M8 x 2
3/8” Hex Bolts (#18), one Bracket (#10), four Ø 5/8” Washers (#26), and four M8
Aircraft Nuts (#24). DO NOT tighten the Nuts and Bolts yet.
B.) Attach the Front Support (#5) to the Main Seat Support (#3). Secure the first hole to
the Main Seat Support with one M8 x 1 5/8” Carriage Bolt (#28), one Ø 5/8” Washer
(#26), and one M8 Aircraft Nut (#24). DO NOT tighten the Nut and Bolt yet.
C.)Attach one end of the Diagonal Support (#4) to the second hole on the Main Seat
Support. Align the holes and secure them together with one M8 x 1 ¾” Carriage Bolt
(#29), one Ø 5/8” Washer (#26), and one M8 Aircraft Nut (#24). Attach the other end
of the Diagonal Support to the Front Support (#5). Secure it with one M8 x ½” Hex Bolt
(#30) and Ø 5/8” Washer (#26).
D.)Securely tighten all Nuts and Bolts previously installed.
DIAGRAM 2
5

STEP 3 (See Diagram 3)
A.) Attach the Leg Developer (#6) to the Front Support (#5). Secure it with one M10 x 2
3/8” Hex Bolt (#21), two Ø ¾” Washers (#31), and one M10 Aircraft Nut (#27). Do not
over tighten the Bolt. Make sure the Leg Developer is able to swivel.
B.) Insert two Foam Tubes (#13) halfway through the holes on the Leg Developer. Push
four Foam Rolls (#12) onto the Tubes from both sides.
C.)Place a Spring Clip (#39) onto the weight post on the Leg Developer.
DIAGRAM 3
6

STEP 4 (See Diagram 4)
A.) Attach the hole-side of the Backrest Supports (#7) onto both ends of the pivot on the Main
Seat Support (#3). Place the other end rest against the Backrest Adjustment Bar (#11).
B.) Place the Backrest Board (#8) onto the Backrest Supports. Secure it with four M6 x 1 5/8”
Hex Bolts (#23) and Ø ½” Washers (#25).
C.)Place the Seat Pad (#9) onto the Main Seat Support. Secure it with four M6 x 5/8” Hex
Bolts (#22) and Ø ½” Washers (#25). DIAGRAM 4
7

STEP 5 (See Diagram 5)
A.) Attach the Arm Curl Pad (#34) to the Arm Curl Stand (#42). Secure it with
two M8 x ¾” Hex Bolts (#33) and Ø 5/8” Washers (#26).
B.) Insert the Arm Curl Stand into the top opening on the Front Support and
secure it with a Lock Knob (#32).
DIAGRAM 5
8

STEP 6 (See Diagram 6)
A.) Slide the 25lb (#36), 15lb (#37), and 10lb (#38) Weight Plates onto the Weight Bar
(#35). Note: Plates must be installed in pairs, one on each side.
B.) Attach two Spring Clips (#39) onto the Weight Bar.
DIAGRAM 6
9