Impex MARCY DIAMOND ELITE MD-440 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MD-440
Retain This
Manual for
Reference
07-23-05
OWNER'S
MANUAL
MARCY DIAMOND ELITE
UTILITY BENCH
MD-440
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICES..................................................................... 2
HARDWARE PACK……….....…....................................................................... 4
ASSEMBLY INSTRUCTIONS........................................................................... 6
EXPLODED DIAGRAM.........................................................................………. 10
PARTS LIST…………………………………………………………………………. 11
WARRANTY.................................................................................................… 12
ORDERING PARTS......................................................................................... 12
BEFORE YOU BEGIN
Thank you for selecting the MARCY DIAMOND ELITE Utility Bench MD-440
by IMPEX INC. For your safety and benefit, read this manual carefully
before using the machine. As a manufacturer, we are committed to provide
you complete customer satisfaction. If you have any questions, or find there
are missing or damaged parts, we guarantee you complete satisfaction
through direct assistance from our factory. To avoid unnecessary delays,
please call our TOLL-FREE customer service number. Our Customer
Service Agents will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]m

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
3. Maximum User’s Weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

WARNING LABEL REPLACEMENT
The Warning Label shown here has been placed on the Front Stabilizer. If the label is missing or illegible, please
call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
3

HARDWARE PACK
4

HARDWARE PACK
5

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended this machine be assembled by two or
more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Main Frame (#1) onto the Front & Rear Stabilizers (#2 & 6). Secure each
end with two M10 x ¾” Allen Bolts (#32) and ∅¾” Washers (#39).
DIAGRAM 1
6

STEP 2 (See Diagram 2)
A.) Attach the Backrest Supports (#3) to the pivot on the Main Frame (#1). Secure it with
one M12 x 5 ¾” Allen Bolt (#31), two Ø1” Washers (#38), and one M12 Aircraft Nut
(#36). Do not over tighten the Nut and Bolt, make sure the Backrest Supports are able
to swivel.
B.) Attach the Backrest Incline Support (#4) in between the Backrest Supports (#3). Secure
it with one M12 x 5 ¾” Allen Bolt (#31), two Ø1” Washers (#38), and one M12 Aircraft
Nut (#36). Attach the other end of Backrest Incline Support to the selected slot on the
Main Frame to obtain the desired backrest incline position.
C.)Place the Backrest Board (#12) onto the Backrest Supports. Secure it with four M8 x 1
5/8” Allen Bolts (#34) and Ø 5/8” Washers (#40).
D.)Place the Seat (#11) onto the Main Frame. Secure it with four M8 x 1 5/8” Allen Bolts
(#34) and Ø 5/8” Washers (#40).
7

STEP 3 (See Diagram 3)
A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it
with one Axle (#42), two M10 x 5/8” Allen Bolts (#30), and two Ø ¾” Washers (#39). Do
not over tighten the Bolts, make sure the Leg Developer is able to swivel.
B.) Insert the U-shaped Pin (#10) into the tube in front of the Main Frame. Secure it with
one Spring (#29), Ø ½” Washer (#28), and M6 x 5/8” Philips Screw (#41).
C.)Insert three Foam Tubes (#9) halfway through the holes on the Main Frame and Leg
Developer. Push six Foam Rolls (#26) onto the Tubes from both ends. Plug six Foam
Roll End Caps (#21) into the Tubes from both ends.
D.)Attach the Curl Bar Handle Support (#45) to the bracket on the Leg Developer. Secure
it with a L-shaped Pin (#27).
E.) Attach an Olympic Sleeve (#14) onto the weight post on Leg Developer. Attach a Spring
Clip (#15) to the Sleeve. DIAGRAM 3
8

STEP 4 (See Diagram 4)
A.) Attach the Arm Curl Pad (#13) to the Arm Curl Stand (#7). Secure it with two M8 x
¾” Allen Bolts (#33) and Ø 5/8” Washers (#40).
B.) Insert the Arm Curl Stand into the front opening on the Main Frame. Use a Lock
Knob (#16) to secure the Stand at desired height.
C.)The Leg Developer can be locked when doing sit up exercise. Simply pull the U-
shaped Pin (#10) out and drop into the hole on the Leg Developer. Remove the
Pin when doing Leg Developer exercises.
D.)Remove the Arm Curl Stand and Curl Bar Handle when using Leg Developer.
DIAGRAM 4
9