Impex AX-266 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
AX-266
Retain This
Manual for
Reference
04-05-05
OWNER'S
MANUAL
APEX COMBO BENCH
AX-266
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN....................................................................................……….. 1
IMPORTANT SAFETY NOTICE.....................................................................……….. 2
HARDWARE IDENTIFIER.....….....................................................................……….. 3
ASSEMBLY INSTRUCTIONS.........................................................................……….. 4
EXPLODED DIAGRAM……….........................................................................………..8
PARTS LIST…………………………………………………………………………………..9
WARRANTY.................................................................................................…………. 10
ORDERING PARTS.......................................................................................…………10
BEFORE YOU BEGIN
Thank you for selecting the APEX AX-266 COMBO BENCH by IMPEX
INC. For your safety and benefit, read this manual carefully before using
the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there
are missing or damaged parts, we guarantee you complete satisfaction
through direct assistance from our factory. To avoid unnecessary delays,
please call our TOLL-FREE customer service number. Our Customer
Service Agents will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]m

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire
manual before you assemble or operate your machine. In particular, note the following
safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

3

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine to avoid
possible injury.
STEP 1 (See Diagram 1)
A.) Connect the two Rear Upright Beams (#1) by the Cross Brace (#2) in the mid-span. Align the
holes then secure each end of Cross Brace with one Bracket (#13), two M10 x 2 3/8” Hex
Bolts (#25), four ∅¾” Washers (#33), and two M10 Aircraft Nuts (#30).
B.) Insert the Backrest Adjustment Bar (#6) through the selected holes on the Rear Upright
Beams to obtain the desired Backrest incline.
C.)Attach the Left and Right Safety Hooks (#16) & (#17) to the top of the Upright Beams. Secure
each Hook with a M6 Aircraft Nut (#32). DIAGRAM 1
4

STEP 2 (See Diagram 2)
A.) Attach the rear of the Main Seat Support (#3) to the Cross Brace (#2). Secure it with one
Bracket (#13), two M10 x 2 3/8” Hex Bolts (#25), four ∅¾” Washers (#33), and two M10
Aircraft Nuts (#30).
B.) Attach the front of the Main Seat Support (#3) to the Front Support (#4). Secure them with
two M10 x 1” Hex Bolts (#26), four ∅¾” Washers (#33), and two M10 Aircraft Nuts (#30).
C.)Attach one end of the Diagonal Support (#5) to the Main Seat Support (#3) and secure it with
one M8 x 2 1/8” Hex Bolt (#27), two ∅5/8” Washers (#34), and one M8 Aircraft Nut (#31).
Attach the other end of Diagonal Support (#5) to the Front Support (#4). Secure it with one
M8 x 5/8” Hex Bolt (#28) and ∅5/8” Washer (#34).
DIAGRAM 2
5

STEP 3 (See Diagram 3)
A.) Attach the front holes on the Backrest Supports (#7) to the pivot on the Main Seat Support
(#3). Place the other end of the Backrest Supports (#7) on the Backrest Adjustment Bar (#6).
Place the Backrest Board (#8) onto the Backrest Supports (#7). Secure it with four M6 x 1
3/8” Hex Bolts (#29) and ∅½” Washers (#35).
B.) Place the Seat Pad (#9) onto the Main Seat Support (#3). Secure it with four M6 x 1 3/8” Hex
Bolts (#29) and ∅½” Washers (#35).
DIAGRAM 3
6

STEP 4 (See Diagram 4)
A.) Attach the Leg Developer (#10) to the front of Main Seat Support (#3). Secure it with a
Hex Socket Axle (#23) and Hex Socket Screw (#24). Attach one Spring Clip (#14) onto
the weight post on the Leg Developer.
B.) Insert the two Foam Roll Tubes (#11) halfway through the holes on the Leg Developer.
Push four Foam Rolls (#12) onto the Foam Roll Tubes from both ends.
C.)Attach a ∅3/4” Washer (#33) onto a M10 x 4 ½” Hex Bolt (#43). Insert the Bolt through
the Butterfly (#40) and secure it with a M10 Regular Nut (#44). Insert the Bolt through
the Upright Beam (#1) and secure it with a ∅3/4” Washer (#33) and M10 Knob (#45).
D.)Insert the Butterfly Foam Roll Tube (#41) through the hole on the Butterfly. Push the
Butterfly Foam Roll (#42) onto the Tube.
E.) Repeat Step C & D above to install the other side. DIAGRAM 4
7

8

PARTS LIST
KEY NO. DESCRIPTION Q’ty
1 Rear Upright Beam 2
2 Cross Brace 1
3 Main Seat Support 1
4 Front Support 1
5 Diagonal Support 1
6 Backrest Adjustment Bar 1
7 Backrest Support 2
8 Backrest Board 1
9 Seat Pad 1
10 Leg Developer 1
11 Foam Roll Tube 2
12 Foam Roll 4
13 Bracket 3
14 Spring Clip 3
15 ∅1” Sleeve 2
16 Left Safety Hook 1
17 Right Safety Hook 1
18 Bushing 6
19 1 ½” Square End Cap 12
20 1” Square End Cap 2
21 ∅1” End Cap 16
22 ∅¾” End Cap 2
23 Hex Socket Axle 1
24 Hex Socket Screw 1
25 M10x 2 3/8” Hex Bolt 6
26 M10 x 1” Hex Bolt 2
27 M8 x 2 1/8” Hex Bolt 1
28 M8 x 5/8” Hex Bolt 1
29 M6 x 1 3/8” Hex Bolt 8
30 M10 Aircraft Nut 8
31 M8 Aircraft Nut 1
32 M6 Aircraft Nut 2
33 ∅¾” Washer 20
34 ∅5/8” Washer 3
35 ∅½” Washer 8
36 Weight Bar 1
37 Weight Plate 25# 2
38 Weight Plate 15# 2
39 Weight Plate 10# 2
40 Butterfly 2
41 Butterfly Foam Roll Tube 2
42 Butterfly Foam Roll 2
43 M10 x 4 ½” Hex Bolt 2
44 M10 Regular Nut 2
45 M10 Knob 2 9