Indiana Furniture Square One 17-14 User manual

800.422.5727 www.IndianaFurniture.com
8x6x8
Model Description 17-14
Quantity
17-2112B Single Block, 24"x12“
(4 Bolts & Nuts Included) 16
17-2424BL Single Block, 24"x24“
(4 Bolts & Nuts Included) 32
17-17596EC End Cap, 96" 5
(used horizontally)
17-17572CP Corner Post, 72" 2
(used horizontally)
17-17596CP Corner Post, 96" 2
(used horizontally)
17-17597CP Corner Post, 97-3/4” 4
17-LEVKIT Leveler Kit, 2 Levelers 10
17-12MMBOLTKIT 12mm Bolt Kit, qty 8 3
Square One
Assembly Instructions
17-14
Tools Needed:
Components:
A
A
B
C
C
D
D
E
17-14 Page 1 of 3
D
D
E
F
F
Drill 6mm Allen Key
Driver Bit
5mm & 4mm
Allen Keys
Box Level Tape
Measure
Ladder 2 to 3
Installers
B
NOTE: Anchoring to floor or wall may require additional tools and hardware. See note at end of instructions.

800.422.5727 www.IndianaFurniture.com
Square One
Assembly Instructions
17-14
17-14 Page 2 of 3
8x6x8
Begin by building the configuration 1 block high. To
establish the configuration footprint.
Align the holes in blocks and connect with 2, 80mm
bolts and 2, 17mm nuts.
Fasten the bolt and nut together but do not
over tighten because you will want to align
and firmly tighten upon final setup.
In the bottom row of blocks install the levelers. Use
the 6mm Allen Key Driver Bit to install the threaded
insert into the bottom holes of the block.
It is important that the threaded insert is
installed as close to perpendicular as possible.
Thread the leveler into the insert. Then thread a
17mm nut onto the top of the leveler.
Connect the Corner Post to the wall sections using
the 60mm bolts and the threaded inserts in the post.
Using a box level to check level, adjust the levelers
on the configuration so they are all touching the
floor.
Install the rest of the blocks using the 80mm bolts
and 17mm nuts until the configuration is built.
1
2
3
4
Box Level Corner Post
Adjust
Levelers
6
5
6
7
17mm nut
Threaded
Insert
Leveler
4
80mm bolt
60mm bolt
17mm nut
Cap, Post, or Beam
2
5
2

800.422.5727 www.IndianaFurniture.com
Square One
Assembly Instructions
17-14
17-14 Page 3 of 3
Install the 97-3/4” Corner Posts & 96” End Cap using
the 60mm bolts.
Using a ladder and an assistant, install the 96”
Corner Posts on the top of the unit using the 60mm
bolts.
Join together 4, 24” x 12” blocks and a 96” End Cap.
Connect 2 of these assemblies with a 96” Corner
Post and 60mm bolts to make an ‘L’ shape.
Using a ladder and an assistant, connect the
assemblies to the top of the structure using the
60mm bolts.
Install 12mm bolts into any unused inserts in the
corner posts.
Once everything is attached, go back and align
components. This may require loosening bolts and
nuts to align. Once adjusted to satisfaction, tighten
hardware to a secure fit.
Your configuration is complete.
If adding Acoustical or Tackable Panels, Acrylic
Inserts, Dry Erase Boards, or TV Mounts, see
individual instructions for installation.
Wall / Floor Anchoring:
Additional support is required for configurations that
are not free standing. Anchoring to the floor, wall,
ceiling, and other furniture will require additional
tools and hardware, not provided by Indiana
Furniture. The installer is responsible for sourcing
hardware and for the installation of support per
building conditions.
8
12
13
10
11
14
9
8
10
11
12
14
8x6x8
96”
End Cap
97-3/4”
Corner Post
96”
Corner Post 96”
Corner Post
14
96”
End Cap