Indiana Furniture One 10 Conference Table User manual

1
One 10: 5 Piece Conference Table Assembly Instructions 144” to 192” Lengths
Parts List:
Qty (3) Short Tops
Qty (4) Long Tops
Qty (2) Trough Assembly
Qty (2) Accent Covers
Qty (16) Jointer Bolts
Qty (8) Jointer Plates
Short L-Brackets
Long L-Brackets
Hardware Included
(4) Bags of #10 x 5
8” Flat Head Screws
(2) Bag of #6 x ½” Pan Head Screws
(1) Bag of ¼”-20 x 2” Bolt and ¼”-20 Nuts
(1) 29mm Silver Polycom Grommet (Optional)
(18) Cover Caps (Optional)
Tools Required
(2) People
Drill with phillips screw bit
5"
32 Allen Wrench
5mm Allen Wrench
10mm Wrench
Level
1” Hole Saw Bit for Polycom Grommet (Optional)
Qty (2) Bases
Qty (1) Mid Leg
2298-1105P144192 5 Pc Conference Table assembly instructions. 144" to 192"

2
Step 1: Remove the accent cover off of the bases by pulling it off.Then bolt together (1) Base and (1) Mid Leg to (1)Trough assembly using the ¼”-20 x 2” Bolt and ¼”-20 Nuts.
Next, Bolt the remaining Trough Assembly to the remaining Base Next screw on the Short L-Brackets and the Long L-Brackets using the #6 x ½” Pan Head Screws. If the table is
48” wide, using the provided Cover Caps, cover the outside holes on the base.
Base With Accent Cover
Base With Accent Cover Removed
Bolt Trough Assembly together in (4) places
and
Bolt Trough Assembly together in remaining (4) places
and
Attach L-Brackets
Place Cover Caps here
on 48” wide tables
2298-1105P144192 5 Pc Conference Table assembly instructions. 144" to 192"

3
Step 2: Place one short end on the end of the Trough Assembly and fasten it to the L-Brackets using #6 x ½” Pan Head Screws. Center the Top from left to right and align the
Top flush with the outside of the base.
Center Top with the Trough Assembly
2298-1105P144192 5 Pc Conference Table assembly instructions. 144" to 192"

4
Step 3: While keeping the outside and top surfaces flush, conenct the remaining tops using the 10mm wrench and the provided Jointer Bolts. Now, fasten the tops to the L-
Brackets with the #6 x ½” Pan Head Screws. Next fasten the Jointer Plates to the Tops using #10 x 7/8” Flat Head Screws. Note: The metal tabs go to the inside of the top
where the top is routed out to accept it.
Place Jointer Bolts in 1st then Fasten the Jointer Plates
Make Top Flush with the outside of the base as shown.
Metal Tabs go to inside of the top
2298-1105P144192 5 Pc Conference Table assembly instructions. 144" to 192"

5
Step 4: Adjust the worksurfaces using the adjustment set screws in the Jointer Plates with the 5"
32 Allen Wrench
Step 5: Level the table using the 5mm Allen Wrench
Fine Tune Adjustment Set Screws
Levelers Are Here
Levelers Are Here
2298-1105P144192 5 Pc Conference Table assembly instructions. 144" to 192"

6
Step 6: Place the Accent in the table, adjust the height of the Accent Cover by using the adjusable levlers on the bottom of the Accent Cover
Step 7: Push on the Base Accent Panels from Step 1
Optional Step 8: Using a 1” Hole Saw Bit, drill a hole in the Accent Cover for the Optional Silver Polycom Grommet.
Bore Hole for Silver Polycom Grommet (Optional)
Push on Base Accent Panels
2298-1105P144192 5 Pc Conference Table assembly instructions. 144" to 192"