Indiana Furniture Square One Quick start guide

800.422.5727 www.IndianaFurniture.com
Square One
General Assembly Instructions
NOTE: Anchoring to floor or wall may require additional tools and hardware. See note at end of instructions.
Tools Needed:
Components:
General Assembly Page 1 of 4
Blocks:
24”x24” Block
(4 Bolts/Nuts Included)
24”x12” Block
(4 Bolts/Nuts Included)
End Caps
Corner Posts
T-Connectors
X-Connectors
Horizontal Beam Spanners
Caps, Posts, and Beams:Hardware:
Review your order acknowledgement/packing slip for components and quantities specific to your configuration.
Leveling Glides
80mm Bolt & Nut
60mm Bolt
12mm Bolt
Drill 6mm Allen
Key
Driver Bit
5mm & 4mm
Allen Keys
Box Level Tape
Measure
Ladder 2 to 3
Installers

800.422.5727 www.IndianaFurniture.com
Square One
General Assembly Instructions
General Assembly Page 2 of 4
End Caps: End caps are required to strengthen Square
One configurations and hide unused bolt holes. End
caps are used horizontally (even number increments) or
vertically (odd number increments). Exception is when
used vertically under a horizontal beam spanner, even
number increments must be used.
Corner Posts: Used where two blocks are joined at a
90 degree angle. Even number increments are used if
an end cap or a horizontal beam spanner spans across
and above the corner post. Odd number increments are
used when no cap or spanner is being used above the
corner post.
T-Connectors: Used where three blocks are to be
joined. Even number increments are used if an end cap
or a horizontal beam spanner spans across and above
the T-Connector. Odd number increments are used
when no cap or spanner is being used above the T-
Connector.
X-Connectors: Used where four blocks are to be
joined. Only odd number increments are available as
horizontal beam spanners and end caps are not
designed to span above an X-Connector.
Horizontal Beam Spanners: Used as a bridge
between two wall sections where an opening is desired.
Even number increments are available for use on top of
a configuration only.
1
2
3
4
Caps, Posts, and Beam Usage
1
2
Corner Post
End Cap
(Horizontal)
End Cap
(Vertical)
T-Connection Beam
X-Connection
Beam
3
4
Horizontal
Beam
Spanner
Even Length
End Cap
(Vertical)
Odd Length
End Cap
(Vertical)
5
5

800.422.5727 www.IndianaFurniture.com
Square One
General Assembly Instructions
General Assembly Page 3 of 4
80mm Bolt & Nut: Used for fastening blocks together.
60mm Bolt: Used to secure a block to a cap, rail, or
beam.
12mm Bolt: Designed to cover up any unused holes in
caps, rails, or beams.
Leveler Kit: The Leveler Kit is comprised of two
levelers, two threaded insert nuts, and two 17mm long
nuts.
In the bottom row of blocks install the levelers. Use the
6mm Allen Key Driver Bit to install the threaded insert
into the bottom holes of the block.
It is important that the threaded insert is
installed as close to perpendicular as possible.
Thread the leveler into the insert. Then thread a 17mm
nut onto the top of the leveler.
Using a box level to check level, adjust the levelers on
the configuration so they are all touching the floor.
6
8
Hardware Usage
7
80mm bolt
60mm bolt
17mm nut
Cap, Post, or Beam
6
7
9
17mm nut
Threaded
Insert
Leveler
9
6

800.422.5727 www.IndianaFurniture.com
Box Level Corner Post
Adjust
Levelers
Square One
General Assembly Instructions
General Assembly Page 4 of 4
Begin by building the configuration 1 block high. To
establish the configuration footprint.
Align the holes in blocks and connect with 2, 80mm bolts
and 2, 17mm nuts.
Fasten the bolt and nut together but do not over
tighten because you will want to align and firmly
tighten upon final setup.
In the bottom row of blocks install the levelers.
Using a box level to check level, adjust the levelers on
the configuration so they are all touching the floor.
Install the rest of the blocks using the 80mm bolts and
17mm nuts until the configuration is built.
A 12 x 24 inch block used horizontally, should have the
single hole face towards the bottom of the configuration.
If connecting 2, 12 x 24 blocks together to fill the space
of a 24 x 24 block. Align the single holes in the 12 x 24
blocks with the holes in the 24 x 24 block.
Additional support is required for configurations that are
not free standing. Anchoring to the floor, wall, ceiling,
and other furniture will require additional tools and
hardware, not provided by Indiana Furniture. The
installer is responsible for sourcing hardware and for the
installation of support per building conditions.
10
11
Block Assembly
14
15
Floor/Wall Mounting:
12
13
16
14
15
Block Assembly Notes:
16
17