Indiana Furniture Square One User manual

36800.422.5727 www.IndianaFurniture.com
Square One
General Assembly Instructions
NOTE: Anchoring to floor or wall may require additional tools and hardware. See your building’s facility manager for proper installation.
Tools Needed:
Components:
General Assembly Page 1 of 3
Blocks:
24”x24” Block 24”x12” Block
24”x48”
Assembled Block
24”x72”
Assembled Block
24”x36”
Assembled Block
24”x60”
Assembled Block
End Caps
Corner Posts
T-Connectors
X-Connectors
Horizontal Beam Spanners
Beams, Caps, and Posts: Hardware:
Review your order acknowledgement/packing slip for components and quantities specific to your configuration.
Leveling Glides
80mm Tool Kit
60mm Tool Kit
12mm Tool Kit
Drill 6mm Allen Key
Driver Bit
5mm & 4mm
Allen Keys
Box Level Tape
Measure
Ladder 2 to 3
Installers

37800.422.5727 www.IndianaFurniture.com
Square One
General Assembly Instructions
General Assembly Page 2 of 3
Plan adequate space for the configuration layout and
an area to sub-assemble square blocks.
For configurations that need to mount to the wall or
floor, locate proper placement for mounting the
configuration. Once the location is measured out and
leveled, pre-drill a pilot hole into the End Cap to use
for connecting to the wall.
If mounting the blocks directly onto a wall, the
through holes located on the blocks can be used.
Make sure to use the correct drill bit size for mounting
hardware specified by the building’s Facility Manager
and type of wall.
There will be pre-assembled sections to assist during
installation. Arrange the “2 High” and/or “3 High”
sections on the floor in an area where the
configuration will be installed.
Begin by aligning holes in blocks on a horizontal
surface. The number of blocks aligned is determined
by the overall wall height (2’, 4’, 6’, or 8’, etc.).
Connect the blocks by aligning the 80mm bolt
(included) into the thru hole and the mating hole, then
adding the connecting nut (included). Fasten the bolt
and nut together but do not over tighten because you
will want to align and firmly tighten upon final setup.
Continue this operation for all vertical sections of the
configuration.
Depending upon the configuration, connect a vertical
Corner Post, T-Connector, or X-Connector with a “3
High” section using the 60mm connection bolts
(included) in the blind threaded inserts.
Attach another “3 High” section perpendicular to
create a self-standing unit, using the 60mm
connection bolts (included) in blind threaded inserts.
Continue to connect the sections together until they
are assembled into the planned layout.
Attach the “3 High” sections in a horizontal manner as
shown in the illustration to the right.
Complete the remaining sections of the typical by
attaching the single blocks.
1
2
3
4
5
5
8
6
7
10
6
8
10
9
9
11
12
11
12

38800.422.5727 www.IndianaFurniture.com
96”
96”
97-3/4”
97-3/4”
Square One
General Assembly Instructions
General Assembly Page 3 of 3
Next step is to connect End Caps using the 60mm
connection bolt and nut (included). Your configuration
may have multiple heights of End Caps. A general rule
of thumb is to use the longer End Caps vertically.
However, where Horizontal Beam Spanners ride across
the top of the End Caps, they are 1-3/4” shorter.
Once the End Caps have been installed vertically,
locate the correct length of horizontal End Caps and
Horizontal Beam Spanners.
Using a ladder and an assistant, place the End Cap
along the top run of blocks. While holding the End
Cap in place, use the 60mm connection bolts
(included) to attach the End Cap along the adjacent
holes of the blocks.
Do the same for the Horizontal Beam Spanners, or
other vertical Caps or Connectors. Note: the
Horizontal Beam Spanners will only have two
connection holes at each end.
Upon having everything setup and attached, go back
and, using a box level, align blocks, End Caps, and
Horizontal Beam Spanners. This may require loosening
bolts and nuts to align. Once adjusted to satisfaction,
tighten hardware to a secure fit.
Your configuration is complete. If adding Acoustical or
Tackable Panels, Acrylic Inserts, Dry Erase Boards, or
TV Mounts, see individual instructions for installation.
13
14
17
18
15
15
16
18
13
14
16