Indiana Furniture Blade One 10 User manual

1
Blade One 10: 4 Piece Conference Table Assembly Instructions 144” to 192” Lengths
Parts List:
Qty (3) Short Tops
Qty (4) Long Tops
Qty (2) Trough Assembly
Qty (16) Jointer Bolts
Qty (8) Jointer Plates
Short L-Brackets
Long L-Brackets
Hardware Included
(5) Bags of #10 x 7/8 ” Flat Head Screws
(2) Bag of #6 x ½” Pan Head Screws
(1) Bag of ¼”-20 x 2” Bolt and ¼”-20 Nuts
(32) ¼”-20 x 1-3/4” Button Head Bolt, ¼”-20
Nuts and ¼” Star Washers
(16) #8 x 5/8” Pan Head Screws
Velcro (For Metal Base Covers)
Tools Required
(2) People
Drill with phillips screw bit
5"
32 Allen Wrench
5mm Allen Wrench
7/16" Wrench
Level
Qty (2) Bases
Qty (4) Large L-Brackets
Qty (4) Small Angle Brackets
Qty (1) Mid-Base
Qty (4) U- Jointer Plates
2298-1104P144192k

2
Step 1:Remove the accent cover off of the bases by pulling it off. Next, Using the supplied Velcro with Self-Stick Adhesive on it, Place the Velcro on the outside of the base and on
the inside of the accent cover along the length of the vertical edge
.
Base with Accent Cover
Base with Accent Cover Removed
Attach Velcro here
Attach Velcro here

3
Step 2: Bolt together the (2) Bases to the Trough assembly using the ¼”-20 x 2” Bolts , ¼” -20 x 1-3/4” Bolts, ¼”-20 Nuts, Large L-Brackets, Small Angle Brackets,
and #8 x 5/8” Pan Head Screws
Step 3: Bolt together Mid base to the trough section using the Large L-Brackets with ¼”-20 x 20” Flat Head Bolts
Fasten Vertical Edge of Large L-
Bracket with ¼”-20x 2” Flat Head
Bolts
Fasten Bottom of Large L-
Bracket with ¼”-20 x1-3/4”
Button Head Bolts
Fasten Small angle Brackets with
(4) #8x 5/8” Here
Fasten Small angle Brackets with
¼”-20x 2” Flat Head Bolts Here
Fasten Vertical Edge of Large L-
Bracket with ¼”-20x 2” Flat Head
Bolts

4
Step 4: Bolt together the remaining trough section to the Mid base along with the remaining Base. Also, install the Short L-Brackets and the Long L-Brackets to the
trough section using the #6 x ½” Pan Head Screws
Short L-Brackets
Long L-Brackets
Step 5: Next fasten the U-Jointer Plates to the short tops using the #10 X 7/8” Flat Head Screws

5
Step 6: Using the supplied Jointer Bolts and a 7/16” Wrench, fasten the tops together as shown (Note: Do not attach the tops to the L-Brackets at this time!)
Jointer Bolt
Step 7: Now slide the tops so the U-Jointer Plate screw holes can be accessed and fasted the plate with the #10X7/8” Screws
Fasten U-Jointer Plate

6
Step 8: Attatch the middle short top to the tops in Step 7. Next, similart to Step 6 attache the remaining tops with the provided Jointer Bolts. Now Slide the tops so the U-Jointer
plate can be attached using the #10 X 7/8” screws.
Middle Short Top
Fasten the U-jointer plate

7
Step 9: Fasten the U-Jointer plates to the Middle Top by using the clearance holes in the trough
Use access holes to fasten U-Jointer Plate
Step 10: Next, attach the remaining jointer plates to the tops and level the tops using the fine-tune adjustments
Fine Tune Adjustments

8
Step 11: Next, Fasten the tops down to the L-Brackets using the #6x 1/2” screws
Attach Tops to the L-Brackets
Step 12: Level the table using the 5mm Allen Wrench. Next (If Applicable) install all power ports and route wires down the base.

9
Step 13: When the Table is completely wired, install the Base Covers. Once the base covers are installed, using the Silver #6 x ½” screws, fasten the covers to the
underside of the trough.
You are Finished!