Indiana Furniture Blade One 10 User manual

1
Blade One 10: 4 Piece Conference Table Assembly Instructions 96” to 120” Lengths
Parts List:
2298-1104P96120K
Qty (2) Short Tops
Qty (2) Long Tops
Qty (1) Trough Assembly
Qty (8) Jointer Bolts
Qty (4) Jointer Plates
Qty (4) Short L-Brackets
Qty (2) Long L-Brackets
Hardware Included
(3) Bags of #10 x 7/8 ” Flat Head Screws
(1) Bag of #6 x ½” Pan Head Screws
(1) Bag of ¼”-20 x 2” Bolt and ¼”-20 Nuts
(8) ¼”-20 x 1-3/4” Button Head Bolt, ¼”-20
Nuts and ¼” Star Washers
(16) #8 x 5/8” Pan Head Screws
(1) 29mm Silver Polycom Grommet(Optional)
Velcro (For Metal Base Covers)
Tools Required
(2) People
Drill with phillips screw bit
5"
32 Allen Wrench
5mm Allen Wrench
7/16" Wrench
Level
Qty (2) Bases
Qty (2) Large L-Brackets
Qty (4) Small Angle Brackets
Qty (2) U- Jointer Plates

2
Step 1:Remove the accent cover off of the bases by pulling it off. Next, Using the supplied Velcro with Self-Stick Adhesive on it, Place the Velcro on the outside of the base and on
the inside of the accent cover along the length of the vertical edge
.
Base with Accent Cover
Base with Accent Cover Removed
Attach Velcro here
Attach Velcro here

3
Step 2: Bolt together the (2) Bases to the Trough assembly using the ¼”-20 x 2” Bolts , ¼” -20 x 1-3/4” Bolts, ¼”-20 Nuts, Large L-Brackets, Small Angle Brackets,
and #8 x 5/8” Pan Head Screws
Step 3: Attach the Short L- Brackets and the Long L-Brackets to the Trough using the Silver #6 x ½ Pan Head Screws
Fasten Vertical Edge of Large L-
Bracket with ¼”-20x 2” Flat Head
Bolts
Fasten Bottom of Large L-
Bracket with ¼”-20 x1-3/4”
Button Head Bolts
Fasten Small angle Brackets with
(4) #8x 5/8” Here
Fasten Small angle Brackets with
¼”-20x 2” Flat Head Bolts Here
Place Short L-Brackets Here

4
Step 4: Next, fasted the U-Jointer Plate to the short tops using the #10 x 7/8” Flat Head Screws.
Step 5: Using the supplied Jointer Bolts and a 7/16” Wrench, fasten the tops together (Note: Do Not Attach the Tops to the L-Brackets at this time!)
Jointer Bolts

5
Step 6: Fasten the (4) Jointer Plates to the tops using the provide #10 X 7/8” screws.
Step 7: Next slide the assembled tops to the side so the U-Jointer Plate can be fastened. Repeat for the opposite side.
Attach (4) Jointer Plates
Slide the Top Assembly to access
the jointer plate
Attach U-Jointer Plate
to the Long tops

6
Step 8: Now, center the top assembly on the trough assembly and if necessary, use the fine-tune adjustment screws to level the work surfaces using the 5/32” Allen wrench. Next,
fasten the top assembly to the L-Brackets with the provided #8 X 5/8” Pan Head Screws.
Fine Tune Adjustment Set Screws
Fine-Tune adjust the work
surfaces, then screw down to the
L-Brackets using the #8 X 5/8”
Screws

7
Step 9: Level the table using the 5mm Allen Wrench. Next (If Applicable) install all power ports and route wires down the base.
Step 9: When the Table is completely wired, install the Base Covers. Once the base covers are installed, using the Silver #6 x ½” screws, fasten the covers to the
underside of the trough.
Levelers Are Here