Inepro IP Card Reader User manual

© 2019 Inepro B.V. All rights reserved
Work Instruction | IP Card Reader - Upgrade
IP Card Reader -
Upgrade

IP Card Reader - Upgrade
Congratulations on your selection of the Inepro IP Card Reader - Upgrade . We are
certain you will be pleased with your purchase of one of the flexibele solutions of the
market.
We want to help you get the best result from your IP Card Reader - Upgrade . This
manual contains information on how to do that; please read it carefully. Due to
continuous product improvements this manual is subject to changes without notice.
We strongly recommend you read the license agreement to fully understand its
coverage and your responsibilities of ownership.
Your Inepro dealer is dedicated to your satisfaction and will be pleased to answer your
questions and your concerns.
Best wishes,
Inepro BV.
The most versatile card reader solution

All rights reserved. No parts of this work may be reproduced in any formor by any means -
graphic, electronic, or mechanical, including photocopying, recording, taping, or information
storage and retrieval systems - without the written permission of the publisher.
Products that are referred to in this document may be either trademarks and/or registered
trademarks of the respective owners. The publisher and the author make no claimto these
trademarks.
While every precaution has been taken in the preparation of this document, the publisher and
the author assume no responsibility for errors or omissions, or for damages resulting fromthe
use of information contained in this document or fromthe use of programs and source code
that may accompany it. In no event shall the publisher and the author be liable for any loss of
profit or any other commercial damage caused or alleged to have been caused directly or
indirectly by this document.
Revision number R 3. This revision of the manual can be applied to products with version Rev. 3
or higher.
Publisher
Managing Editor
Technical Editors
Cover Design
Inepro B.V.
K. de Graaf
P. Blom
K. de Graaf
Production
Inepro B.V.
Team Coordinator
R. Groen
H. Wagenaar
P. Grimmerink
IP Card Reader - Upgrade

Table of Contents
Introduction 1
Package Content 3
Software Installation 5
Hardware Installation 8
Programming Instructions 12
Troubleshooting 20

ATTENTION!!
Read this manual carefully before installing the C ard Reader!
Mains connection
Changes and/or mdodifications
Security
Before connecting the appliance to the mains, check that the mains supply v oltage corresponds
to the voltage printed on the type plate of the adapter. If the mains voltage is different, consult
your supplier.
Changes and/or modfications whch have not been approved by the responsible party can void
the user's authorty to operate the equitement.
Always disconnect the power supply before handling anything inside the device.
This dev ice is complies with part 15 of the FC C rules, operation is subject to two conditions:
(1) This dev ice may not cause harmful interference.
(2) This dev ice must accept any interference received, includng interference that may cause
undesired operation.
FCC Federal Communications Commission - US
End of life directives
Inepro is paying a lot of attention to environmentally-friendly production. Your new dev ice contain
materials which can be recycled and reused. At the end of its life specialised companies can
dismantle the discarded device to recycle the reusable materials and to minimise the amount of
materials to be disposed of. Please observe the local regulations regarding the disposal of
packaging materials, exhausted batteries and old equipment.
This device may only be used indoors.
Indoor User Only
Directives
I
This device is in conformity with the EMC directive and low-voltage directive.
CE Conformité Europeène (Conform European Norm)
Guarentee
No guarantee can be given if safety regulations are not followed.
Appareil concernés:
MCR708, MC R708G, DCR708, DC R708G
Le présent appareil est conforme aux CNR
d’Industrie Canada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions
suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le
fonctionnement.
Conformité d’Industrie Canada Relev ant Devices:
MCR708, MC R708G, DCR708, DC R708G
This dev ice complies with Industry C anada’s
licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This dev ice may not cause interference; and
(2) This dev ice must accept any interference, including
interference that may cause undesired operation of the
dev ice.
Confirm Canada Industries

I
Introduction
Part

Introduction
2
Introduction
This short manual will guide you trough the upgrade process of the
Inepro IP Card Reader.
Please follow the instructions closely.

II
Package Content
Part

Package Content
4
Package Content
Inepro IP Card Reader Interface Package
1. Flat cable for communication between the programmer and
interface board
2. USB cable for connection with the PC
3. Melabs U2 Instruction Sheet
4. Melabs U2 Setup CD
5. Melabs U2 Programmer Unit

III
Software Installation
Part

Software Installation
6
Software Installation
1. First setup the Melabs programmer software application.
2. Please insert the installation CD.
3. Choose 'Execute Setup.exe'
4. Click 'Next'
5. Choose 'Iaccept the agreement'
6. Click 'Next'
7. Click 'Next'
8. Click 'Install'

7 - IP Card Reader - Upgrade
9. Wait for the installation to finish
10. Click 'Next', ticking the boxes is
optional
11. Read the information, and click 'Next'
12. Finish the installation

IV
Hardware Installation
Part

9 - IP Card Reader - Upgrade
Hardware Installation
1. Screw the Inepro IPCard Reader box open and take out the Interface
connector board.

Hardware Installation
10
2) Connect the USB cable to the PC you installed the software on
and the programmer unit.
3) Connect the black connector of the flat cable to the programmer
unit in such a way that the red side of the cable is on the left side
(this is the same side as pin 1 on the diagram on the
programmer). The cable will be running away from the
programmer unit.
Make sure you fit the cable correctly as it can fit in more then
one way! Failing to do so may result in a defective programmer unit
or a defective Interface board!
Repairing the resulting problems will not be covered by the
guarantee!
Connect the other end with the red side of the cable to the closest
short edge of the connector board, the connector should only fit in
one way, with the plastic rims gliding along the socket.

11 - IP Card Reader - Upgrade
4) To supply power use one of the following options:
a) Connect the power adaptor to the black socket next to the
network connectors.
b) Connect a Power over Ethernet (PoE) network cable to the
PoE connector on the board.
The Power over Ethernet option requires the implementation of
Power over Ethernet in your network, otherwise no power can be
supplied.
The power adapter was supplied together with the Inepro IP Card
Reader.

V
Programming Instructions
Part

13 - IP Card Reader - Upgrade
Programming Instructions
To program the Inepro IP Card Reader, you need a hex-file. This
file should be supplied by Inepro and is customized to meet your
requirements.
1. Start the mePROG.exe executable.
2. Choose 'File' -> 'Open'.
3. Open the hex-file that Inepro supplied. The selected hex
filename will be shown in the title bar of the application window.
Double check if this name is correct.

Programming Instructions
14
4. Set all the ticks in the 'Options', 'More Options' and 'Program'
submenu's as shown in the image above.

15 - IP Card Reader - Upgrade
5. Tick all the options in the 'Verify' menu, as shown in the image
above.