Inner Range CONCEPT IQ. PLUS Operating and maintenance manual

Ver. 3.003 p1
CONCEPT IQ. PLUS Programmer’s Manual.
Programmer’s Manual
© 2003. Inner Range Pty. Ltd. Part Number: 630047plus
PLUS

p2 Ver. 3.003 (24/4/03) CONCEPT IQ. PLUS Programmer’s Manual.
TABLE OF CONTENTS.
Programming Methods ............................................................. 3
1. Introduction
1.1 SystemOverview............................................................... 4
1.2 Types of Users................................................................... 6
1.3 Default Users..................................................................... 6
2. The LED Terminal
2.1 Key Functions.................................................................... 7
2.2 Beeper Indications ............................................................. 7
2.3 Lamp Indications ............................................................... 7
2.4 Access Control & IQ Plus .................................................... 8
3The Programming Key
3.1 Introduction........................................................................ 9
3.2 Import Data from Programming Key ................................... 9
3.3 Export Data to Programming Key ....................................... 9
4ProgrammingTechniques
4.1 The System Database........................................................ 10
4.2 Selecting and Programming the Data ................................. 10
4.3 Types of Data .................................................................... 10
4.4 Example of Programming .................................................. 11
4.5 Programming Flowchart ..................................................... 11
4.6 “Value” Data....................................................................... 12
4.7 “Options” Data ................................................................... 12
4.8 Defaulting the System ........................................................ 13
5User Operation Summary
5.1 General User Operations (No PIN Code)............................ 14
5.2 User Operations requiring PIN Code .................................. 14
6Master User Operation Summary
6.1 Master User Operations ..................................................... 15
6.2 User Programming ............................................................ 16
7Basic Programming Guide ........................................................ 18
8ProgrammingofAdvancedFeatures
Contents and Overview............................................................. 34
Access Control Options ............................................................ 35
Auto-Arm / Auto Disarm. ........................................................... 36
AuxiliarytoFollowaTimeZone ................................................. 37
BatteryTesting.......................................................................... 37
Callback for Remote Connect. .................................................. 38
Call Forwarding. ....................................................................... 38
Computer connection (Local) .................................................... 38
Printer connection (Local) ......................................................... 38
DayAlarm. ............................................................................... 38
DeferArming ............................................................................ 39
DTMF Remote Control (Telephone Remote Control) ................. 39
KeyswitchArmingandDisarming. ............................................. 39
Pulse Counting. ........................................................................ 40
Siren output to operate as an Auxiliary. ...................................... 40
Six Digit PIN Codes. ................................................................. 40
Smoke Detector Reset ............................................................. 41
SubAreas. ............................................................................... 41
UserAuxiliaries ........................................................................ 41
Walk Testing............................................................................. 42
Wireless Remote Control. ......................................................... 42
Zone Self Testing...................................................................... 42
9Programming Reference........................................................... 43
ArrangednumericallybyAddresslocation.
10 Tables ...................................................................................... 74-84
AuxiliaryEventTypes................................................................ 75-77
AuxiliaryActions. ...................................................................... 78
System Inputs........................................................................... 79
Contact ID Event Codes. .......................................................... 80
Factory Default and Installer Preset Configurations ................... 81-84
Printer Output, Review Format .................................................. 85
11 Indexes .................................................................................... 86
Alphabetical Index .................................................................... 86
Numerical Index (By Address Location)..................................... 90

Ver. 3.003 p3
CONCEPT IQ. PLUS Programmer’s Manual.
PROGRAMMING METHODS
Concept IQ has been designed to provide a versatile system that is quick & easy to program & commission.
THERE ARE 5 WAYS TO QUICKLY PROGRAM YOUR CONCEPT IQ.
FROM THE PROGRAMMING KEY
FROM A COMPUTER
FROM THE LED TERMINAL
2Upload / Download Software
Allows system programming while on-line to
the Controller or while off-line. Connection
can be via local Serial Port (using the “Port 0
Cable”) or via remote dial-up. This software
is also used to view “Review” history.
Download for free from www.innerrange.com
3Factory Defaults
Much of the basic system
programming can be quickly
implemented by selecting one
of the System Default options.
See Page 13 of this manual for
the Default procedure and an
overview of the System Default
options.
See the Tables section for a full
description of each System
Default option.
4Address Location
-Numerical Order
Use Section 9 -”Programming
Reference” to program the
system in numerical Address
order.
401-495 Users.................. 43
500-520 Comms .............. 44
521-569 Areas.................. 50
570-589 Holidays ............. 54
590-595 Daylight Saving .55
600-741 Zone Inputs........ 56
750-769 TimeZones......... 61
800-870 Auxiliaries .......... 62
890-893 General Opts ..... 64
897-899 System Inputs.... 67
900-914 Times/Counts .... 69
918-919 Access Control.. 72
5Primary and
Secondary option
programming.
In many cases, a system can
be fully programmed by
following theBasic
Programming Guide
flowchart steps described in
Section 7
Additional Features can then
be added by following the
Advanced Feature
Programming described in
Section 8
Section 9 -Programming
Reference can be used for
additional details whenever
required.
1Portable Memory Device
Used to Download programming data into a
Controller that has been copied from another
Controller or from a Computer.
See page 9 of this manual.

p4 Ver. 3.003 (24/4/03) CONCEPT IQ. PLUS Programmer’s Manual.
1.1 SYSTEM OVERVIEW
The Concept IQ is an affordable, simple to use security system targeted at the domestic
and small commercial markets. The system has been designed for ease of use by the
Installer and the End User.
SYSTEMHARDWARE
The basic Control Module has the following hardware dimensions:
•Zones: 8 standard Zone Inputs or 16 doubled Zone Inputs.
•Auxiliaries: Total of 3. 1 Siren speaker / 1 Strobe / 1 General purpose.
•Serial Communications Port: RS232.
•External Device Bus.
•System LAN: Provides connectivity for up to 4 LAN Devices.
•IO Expansion Bus.
•Separate Tamper Input.
A variety of Peripheral devices can be connected directly to the Control Module:
•Programming Key.
•Plug-on Expansion Card options. 8 additional Auxiliaries and/or 8 additional Zones.
•DTMF communications Card.
•DTMF + Voice communications Card.
•Serial Adapter Cable for connection to PC.
The System LAN supports the following LAN Modules:
•Standard 16 Zone / 4 Area LED Terminal.
•RF Terminal that adds 2 key or 4 key radio remote functionality.
•Enhanced Terminal that adds access control.
FUNCTIONAL DESCRIPTION
Zone Inputs. Zone Inputs are individually programmed to define how they are to be
processed. An appropriate “Zone Type” is chosen and additional
options relating to; Alarm Processing, Reporting, Siren, Pulse
counting, Testing, and type of Input Device can also be defined.
Global Zone options also allow system-wide parameters to be set for
Pulse Counting, End-Of-Line Resistor values and Zone Self Testing.
System Inputs. System Inputs are available for monitoring Faults and System Alarms
such as; Power Problems, Cabinet & Siren Tampers, Communication
Problems, LAN & Battery Fuses, Zone Self-test Status and Keypad
Emergency Alarms (Panic, Fire, Medical & Duress).
System Inputs are also available for monitoring Door Forced and Door
Open Too Long (DOTL) alarms, allowing operation of auxiliaries and
other General Options.
Automatic Battery Testing is available and triggers the Low Battery
alarm if the test fails.
The Installer enables the Siren and Reporting (to Fault History and/or Reveiw or through the
dialer) options for each System Input as required.
Areas. The system can be configured in Single Area or Multi Area Mode
according to the site requirements. Up to 4 Areas are available and
Zone Inputs can be assigned to one or more Areas. Each Area can be
armed in “AWAY” or “HOME” modes.
Each LED Terminal can be configured for Multi-Area mode or assigned
to a Single Area.
Review General Review is a history of events available to the Upload/
Download software or direct to a Printer in real time (IQ Plus only see
Tables - Section 10). Events such as alarms, restores, tampers, open,
close and system inputs are time stamped and entered into Review.
General Review contains a maximum of 128 entries, once Review is
full, older events are lost as new ones are entered.
Unique to the IQ Plus is “Access Review” events such as REX button, Door Forced, Door
Open Too Long (DOTL), valid and invalid card read and access entry are all viewable (requires
an add-on to the Upload/Download software). Access Review contains a maximum of 42
entries, once Review is full, older events are lost as new ones are entered.
General Options can be set, to allow Access Review to be written to General Review, this
option should be used with caution because of the limited size of the Review buffer.
1. INTRODUCTION

Ver. 3.003 p5
CONCEPT IQ. PLUS Programmer’s Manual.
Siren. The Siren Speaker output supports a standard 8 Ohm Horn speaker
and can generate 4 different siren tones for Burglary, Fire, Medical &
Panic alarms. The Siren time is programmable and any System Input
Alarms that are programmed to activate the Siren may be differentiated
from Zone Input Alarms by a different Siren tone.
Auxiliaries. Auxiliary outputs are extremely flexible with a range of versatile
programming options for Security and Building/Home automation. A
choice of over 50 “Auxiliary Types” provides for Auxiliaries to;
Annunciate different types of alarms, Indicate (mimic) individual Area or
Zone status, Indicate Entry, Exit, Auto-Arm & Zone Bypass conditions,
Follow TimeZones, etc.
For each individual Auxiliary the output logic and On/Off actions can be
tailored including an optional timer that can be programmed in Minutes
or Seconds.
Communications. The system offers “Contact ID” or “Domestic” dialing options. For a
higher level of Dialer integrity a Secondary telephone number can be
programmed, Telephone line monitoring is provided and the maximum
number of dial attempts can be specified. A “Comms Fail” alarm is
activated if the line is tampered or the maximum attempts is reached.
Daily, Weekly or Monthly Test reports can also be sent at a specified
time of day, or triggered manually by a Master User.
The Installer can dial in to the system from a PC for Upload/Download
when required. Security is provided by a PIN code requirement, and
Callback and Fax Bypass options are available.
With the DTMF Card fitted, a User can dial in to the system, and using
their PIN code, can perform remote operations and obtain system
status information.
The IQ Plus provides two On-board Serial Ports, allowing connection of
a Programming Key or PC for Upload / Download or to a Printer to print
Review output.
Timers. An extensive range of Timers are provided catering for; Individual Area
Exit/Entry delays, System Siren time, Keypad lockout time and AC fail
delay time. Four TimeZones are provided including provision for up to
10 Holiday dates and automatic Daylight Saving adjustment is also
catered for.
The TimeZones can be used to turn Auxiliaries On and/or Off and to
control Areas.
User Functions. In addition to the User operations described in “Types of Users” below,
the system provides a number of options to simplify and/or enhance
the User operations and feedback.
These include; Auto-Isolate on Arming, Quick Arming, Key-switch Arm/
Disarm and Zone activity display on LED Terminals.

p6 Ver. 3.003 (24/4/03) CONCEPT IQ. PLUS Programmer’s Manual.
User Number Description Factory Default PIN
User 1 Installer 2345 (or 234567)
User 2 Master User 0123 (or 012345)
User 3 to 95 General Users
(Can be programmed as a Master User) None
User 96 Reserved for system functions
(e.g. Reporting Auto-arming etc.) Not applicable
1.2 TYPES OF USERS
The system has 3 special Users and 93 normal Users. The system can be configured for
4 digit or 6 digit PIN codes depending on the requirements of the site. The normal Users
can each be assigned a “User Type” and their “User Areas” to define the items that they
can control and the operations that they can perform.
INSTALLER - USER 1:
Can perform all Installer operations, and all Master operations.
MASTER USER - USER 2:
Can perform all the Master operations and has access to all Areas.
The Master operations include; Edit Users, Walk test Zones, Set Tme & Date, Siren/
Strobe/Auxiliary Testing, Fault Analysis, View Software Version, Test Battery and Door Bell
Enable/Disable.
The Master User can also perform all User operations. This includes Arming / Dis-arming
the system, Isolating Zones and View history.
The Master User automatically has permission to control all the Areas, Zones and Auxiliary
outputs in the system.
NORMAL USERS - USER 3 TO USER 95:
Can perform a variety of operations such as Arming / Dis-arming , Isolating Zones and
View History with various levels of functionality as defined by the User’s “User Type”.
Can also be programmed as a Master User if required. In a Multi-Area system, a normal
User programmed as a Master User can only add a new User or edit existing Users who
can access a subset of their own Area list.
DURESS CODES.
A User PIN’s last digit + 1 will form a DURESS Code.
e.g. If a user’s PIN is 1234, then 1235 will trigger a duress alarm, and if the user’s
PIN is 1239, then 1230 will be a duress code.
1.3 DEFAULT USERS:
The Default Installer PIN and Master PIN Codes should be changed as soon as possible
after installation.
When choosing a new PIN Code, ensure that a PIN is chosen that will not be forgotten,
while still providing security against unauthorised access.

Ver. 3.003 p7
CONCEPT IQ. PLUS Programmer’s Manual.
2. THE LED TERMINAL
PANIC. Keys 1 & 3 pressed simultaneously.
FIRE. Keys 4 & 6 pressed simultaneously.
MEDICAL. Keys 7 & 9 pressed simultaneously.
REX (Request to Exit) <OFF> key.
Enhanced Terminals only.
2.1 KEY FUNCTIONS.
NEXT -Installer: Select a Programming Address or Installer operation.
-Master User: Select a Master User operation.
HOME -In Single Area Mode: Used to Arm the system in Home Mode.
-In Multi-Area Mode: Used to Arm the specified Area in Home Mode.
-Master User: Clear the data already entered if you make a mistake.
CLR Logoff the Terminal. Exit the current Mode of operation)
ENTER Saves the data entered in a programming Address.
NOTE: AUTO-LOGOFF: The Terminal will automatically logoff the operator if there is
no keypad activity detected for 30 seconds.
2.2 BEEPER INDICATIONS.
2 or 3 Short Beeps: A User, Master or Installer function was successful.
1 Long Beep: A User, Master or Installer function has been unsuccessful.
When an error is detected, the beeper tones will sound at a
lower pitch until a correct operation is successfully performed.
Continuous Short Beeps*:Entry Delay Timer, Exit Delay Timer or Auto-arm Warning.
*NOTE:
Single Area systems. All Terminals will beep in response to Exit delay, Entry delay or
Auto-arm warnings.
Multi-Area systems. Only Terminals associated with a particular Area will beep in
response to that Area’s warning functions.
IMPORTANT NOTE: Multi-Area Terminals will beep on
warning functions from all Areas.
2.3 LAMP INDICATIONS.
*Alarm indication takes priority over Isolate or other indication.
^See “System Inputs” on page 72 in the Tables section.
Lamp ON OFF FLASHING
ZONE Lamps
1 to 16 When the Zone is Unsealed.
(If the "Zone activity"
option is enabled)
When the Zone
is Sealed. FAST: * When there has been an Alarm / Tamper on the Zone.
SLOW: * When the Zone has been Isolated.
AREA Lamps
A1, A2, A3, A4 Area is Armed. (Multi-Area mode
only)
Area is Dis-armed. Note: Multi-Area mode only.
FAST: * There has been an Alarm in the Area.
SLOW: * Area Armed in Home Mode.
ARM Area/s are armed
in Away mode. System not armed in Away mode. There has been an alarm in an Area armed in Away mode.
HOME Area/s are armed
in Home mode. System not armed in Home mode. There has been an alarm in an Area armed in Home mode.
FAULT ^ A system input is
currently in alarm. ^ No system inputs are in alarm. SLOW: When a System Input has been Isolated. ^
PWR AC mains OK AC mains problem. -
ARM & HOME --System is in "Master Operations" mode.
i.e. NEXT functions.
ARM, HOME &
FAULT. - - System is in "User Programming" mode.
ARM, HOME,
FAULT & PWR - - System is in "Installer Programming" mode.
0Used to display values in programming mode.

p8 Ver. 3.003 (24/4/03) CONCEPT IQ. PLUS Programmer’s Manual.
2.4 ACCESS CONTROL AND THE IQ PLUS.
REQUIRED EQUIPMENT.
Enhanced Access Terminal V2.01 or greater; Door strike; Relay board for door strike;
Wiegand reader. The Terminal installation document 635500EN contains additional informa-
tion on installation.
DOOR OPTIONS.
The Door (door strike and door reed switch) connected to the Terminal is automatically
associated with that Terminal and can be referred to by the Terminal number, for example;
Terminal 1 = door 1. Terminals can be associated to areas and will only display zone activity
for that Area. (Address 561-564)
All doors will use the same global lock open time (time the door strike is activated) as
programmed at address 909 - Terminal Auxiliary time. This must be programmed to a value
other than 0 for the door to remain open following a valid request to open. If a 0 is left at
this location the lock will open but close again almost immediately, i.e. remain locked.
Valid entries are from 0 to 255 seconds. (Factory default 5 Seconds).
REQUEST TO EXIT BUTTON.
A “Request to Exit” (REX), is typically a button provided to unlock a door from the inside
either bypassing the need to use a reader during low security periods, or because an internal
(exit) reader is not required. The “REX” device can also be a PIR or Photo-Electric beam to
detect the User approaching the door. If a REX button is fitted it will activate the door for the
lock open time (see above). The REX operation is enabled regardless of the state of the
associated Area and is entered into Access Review.
The OFF key can also be used as a REX button if it is programmed at address 918.
ADDING A CARD AND USER PIN.
Once fitted and tested, learning the card (entering the card details into the panel) is done
exactly the same as adding a User PIN with the exception that the card is also presented
(explained in detail in section 7, the Basic Programming Guide).
A User can have both a PIN and card, accessing the door using either method. A reader
need not be fitted if PIN only access is required. The door will open for lock open time
following a valid PIN + OFF key.
For higher security applications, both PIN and card can be required to open the door.
This option is global and is set at Address 919.
Each door will assume Area control of the Area associated with the Terminal, a Terminal
MUST be associated with an Area.
The following rules apply:
1) If the User is assigned to an Area that is also associated to the Terminal,
(a)If the Area is armed, badging a card will disarm the associated Area and open the door.
(The event is entered into Access Review).
(b) If the Area is disarmed, badging a card will open the door. (The event is entered into
Access Review)
2) If the User is not assigned to the Area associated to the Terminal,
(a) If the Area is armed, badging a card will not open the door (The event is entered into
Access Review).
(b) If the Area is disarmed, badging a card will open the door (The event is entered into
Access Review).
DOOR FORCED
A Door Forced condition is activated when the reed switch goes into alarm without a valid
request to open the door, this also causes the Door Forced system input to go into alarm.
(The event is entered into Access Review)
An Auxiliary can be used to indicate this system input by setting the Auxiliary type; 131
(door1)-138 (door 8) as described in the Tables-Section 10. This Auxiliary will pulse on for
500ms every 5 seconds till cleared. Door Forced is an Alarm condition and is cleared by
using a valid PIN+OFF key.
DOTL
A DOTL (Door open too long) condition is activated when the door is open for longer than a
period of time equal to 4 times that of the lock open time set at Address 909. This means
that once a valid request to open occurs, the lock timer starts and so does the DOTL timer.
Causing the DOTL system input to go into alarm. (The event is entered into Access Review)
An Auxiliary can be used to indicate this system input by setting the Auxiliary type;
141(door 1)-148 (door 8) as described in the Tables-Section 10. This Auxiliary will pulse on
for 500ms every 5 seconds till cleared. DOTL is a warning condition and is cleared by
using a valid PIN + OFF key or a valid card badge.

Ver. 3.003 p9
CONCEPT IQ. PLUS Programmer’s Manual.
3. PROGRAMMING KEY
3.1 INTRODUCTION.
THE PROGRAMMING KEY.
The Concept IQ Programming Key is a portable non-volatile memory device housed in a
convenient “key tag”.
The Programming Key allows system programming to be uploaded from the Control
Module or downloaded to the Control Module by simply inserting the Programming Key
into Serial Port 0 and performing a simple key sequence on the LED Terminal. See below.
A built-in Lamp (embedded in the plastic surface) on the Programming Key visually
indicates when data transmission is active.
CONCEPT IQ PROGRAMMING KEY & FLASH INTERFACE.
This device allows the Programming Key to be connected to a PC for transferring Panel
data to and from the Upload/Download software.
NOTE: The Concept IQ Programming Key & Flash Interface can also be used to connect
a PC to the “Flash” connector (JP8) on the Controller for the purpose of providing a Flash
Upgrade of the Controller Firmware version.
Refer to your Concept IQ distributor for more details.
IMPORTANT NOTE: The new data will override the existing contents of the Control
Module memory.
Connect the Programming Key to Serial Port 0 on the Control Module.
Select the Import Data Mode:
Enter PIN; ... , then , then the Mode number; , , .
The Lamp on the Programming Key will flash slowly to indicate data is being copied.
The Terminal beeper will sound 3 short beeps if the operation was successful, or 1 long
beep if unsuccessful.
3.3 EXPORT DATA TO THE PROGRAMMING KEY.
This Mode allows the Installer to copy the programming contents of the Control Module into
the Programming Key.
IMPORTANT NOTE: The Control Module data will override the existing contents of the
Programming Key.
Connect the Programming Key to Serial Port 0 on the Control Module.
Select the Export Data Mode:
Enter PIN; ... , then , then the Mode number; , , .
The Lamp on the Programming Key will flash quickly to indicate data is being copied.
The Terminal beeper will sound 3 short beeps if the operation was successful, or 1 long
beep if unsuccessful.
3.2 IMPORT DATA FROM THE PROGRAMMING KEY.
This Mode allows the Installer to copy the programming contents of the Programming Key
into the Control Module.
Door Forced and DOTL system inputs will turn on the fault light on the Terminal and LEDs
15 or 16 when a NEXT 13 is performed. (Refer System Inputs) The Zones Inputs on terminals are used for door reed switch (zone1) and REX button
(zone2). Each zone must be fitted with the required device or, if not used, must be termi-
nated with 6k8 resistors. These Zones cannot be used for security zones.

p10 Ver. 3.003 (24/4/03) CONCEPT IQ. PLUS Programmer’s Manual.
4.1 THE SYSTEM DATABASE.
User programming is stored in Memory Addresses numbered from 401 to 447.
The system programming is stored in Memory Addresses numbered from 500.
Programming the system involves three basic steps:
1) Logon with the Installer PIN Code.
Then for each item of Data to be programmed;
2) Select the Memory Address to be programmed.
3) Program the new Data Value or Options for that Address.
4.2 SELECTING AND PROGRAMMING THE DATA.
TO SELECT THE ADDRESS OF THE DATA TO BE VIEWED OR EDITED.
1. Key in the Installer PIN Code.
2. Select the Address of the data to be viewed or edited by simply pressing:
followed by the Address number; , , (3 digits).s).
Flashing Area Lamps will prompt you for each digit of the Address to be entered
i.e. A1 = Key in the 1st digit of the Address; A2 = Key in the 2nd digit of the Address; etc.
As each digit is entered, the corresponding Area Lamp will stop flashing and remain on.
ARM, HOME, FAULT & PWR Lamps will Flash to indicate “Programming Mode” as soon as
the 1st digit of a Programming Address has been entered. When the Address has been
fully entered, the A4 lamp will flash if data is already programmed in that Address.
Pressing after entering the data will save the data and automatically take you to the
Next Programming Field or Address.
Pressing after entering the data will save the data and automatically take you to the
Previous Address.
4. PROGRAMMING TECHNIQUES
TO EDIT THE DATA.
The Data Value at the Address selected will then be displayed via the Terminal Lamps, and
can be changed by simply keying in the new data according to the Type of Data.
Enter the new Data (Value or Option) settings ... (1 to 16 digits*), then (Too
advance to the Next Address) or (To go to the Previous Address)
* Depending on the type of Data required. See 4.3 following.
Flashing Zone Lamps will prompt you for each digit of the data to be entered
i.e. 1 = Key in the 1st digit of the data; 2 = Key in the 2nd digit of the data; etc.
As each digit is entered, the corresponding Zone Lamp will stop flashing and remain on.
To clear the current field of all data and settings, ready for new data, press .
e.g. If you make a mistake while entering a value, press and enter that value again.
EXITING PROGRAMMING MODE.
Press to exit any of the Installer Operations.
4.3 TYPES OF DATA.
When in Programming Mode there are two types of data that are stored in the
Programming Addresses. The type of Data stored in each Address will depend on the type
of parameter being defined.
1) “Value” data. A Numerical Data Value that:
•Selects an Option when there are more than 2 alternatives to select from.
e.g. Reporting Format or User Type.
•Defines a Value or Quantity for a specific parameter.
e.g. Entry and Exit Delay times or Number of Dial attempts.
•Defines a Sequence of numbers for a specific parameter.
e.g. PIN codes, Client codes and Telephone numbers.