Insignia GT 8058R User manual

insigniarange.com Last Modified: 23/01/2014
INSTALLATION MANUAL
GT 8058R
ATTENTION INSTALLERS:
These instrucons must be
le with the customer
30 Day Technical Support: 01908 226545
(NOTE: This service is only available to customers from the day of delivery,
please have your supplier’s details and your postcode to hand before calling)
Replacements Parts: inside of your warranty contact:
www.insigniarange.co.uk/customerSer ice.aspx
Spares/Replacements Parts: outside of your warranty
contact 0844 800 3069
www.insigniarange.co.uk
WARRANTY REG NO: __________________________
To claim your full 5 year warranty, register your shower within 90 days of deli ery at: www.insigniarange.co.uk/
warrantyreg.aspx. Standard 12 month warranty applies if outside this me period.

insigniarange.com Last Modified: 23/01/2014
02
Contents
Introduction
Electrical Requirements
What’s In The Boxes?
Screw Pack Contents
Plumbing Requirements
Starting The Installation
Electric Box Connections
Steam Generator Connections
Sealing and Water Testing
MK117 Control Panel Instructions
Hel Book Information
Parts list
3
6
7
8
9
20
22
23
24
2
26

insigniarange.com Last Modified: 23/01/2014
03
Thank you for your recent purchase of an Insignia shower. Please read this booklet with great care to ensure you get the best out of your build and have a shower that
will last for many years to come!
Like everything, in order to obtain a first class product that will serve you well for many years, the effort and correctness put into the assembly will reflect in the quality of
your finish.
OUR BADGE RATING IN TERMS OF DIFFICULTY OF ASSEMBLY IS BASED ON CLIENT FEEDBACK
1 Badge = Very easy
2 Badges = Easy
3 Badges = Moderate
4 Badges = Harder than average
Badges = Professional skills required
This shower is rated Badges

insigniarange.com Last Modified: 23/01/2014
04
ASSEMBLY AND SIMPLE PLUMBING
THIS PRODUCT BUILD IS RATED SUITABLE FOR DIY PURPOSES PROVIDING THE CUSTOMER IS OF ABOVE AVERAGE SKILLS AND FEELS CONFIDENT IN
THEIR ABILTY. ONLY YOU THE CUSTOMER WILL KNOW THIS SO BEFORE ANY ATTEMPT IS MADE TO ASSEMBLY READ THROUGH THE FOLLOWING PAG-
ES IN DETAIL THEN DECIDE. IF YOU HAVE ANY DOUBT USE THE SERVICES OF A PROFESSIONAL. IN PICKING SUCH, ALLOW THEM TO DECIDE IF THEY
ARE CAPABLE OF BUILD BY FIRST SHOWING THESE INSTRUCTIONS TO THEM. ALWAYS GET THREE QUOTES.
REMEMBER THE BEST IS NOT ALWAYS THE CHEAPEST!
REMEMBER PLUMBERS PLUMB! 90% OF THIS JOB IS NOT PLUMBING!
DUE TO THE NATURE OF THIS PRODUCT WE HIGHLY ADVISE THE PURCHASE AND FITTING OF A WATER SOFTENER
ELECTRICAL CONNECTION TO HOUSE MAINS
WHEN YOUR ITEM IS ASSEMBLED ALWAYS USE THE SERVICES OF A FULLY QUALIFIED ELECTRICAL COMPANY TO COMPLETE CONNECTION FROM
SHOWER TO HOUSE SUPPLY. LAWS DEMAND IN MANY CASES YOU DO THIS AND YOUR WARRANTY IS VOID REGARDS ELECTRICAL ITEMS IF THIS IS NOT
UNDERTAKEN.
YOURS AND OTHERS SAFETY IS PARAMOUNT. NEVER ATTEMPT THIS YOURSELF.
REMEMBER:
These showers are designed to be free standing and movable from their location should you have need to replace anything. ALWAYS USE Flexible braided water inlet
pipes at least a metre long (not central heating plastic type! )
from house supply to the shower and again flexible waste pipe to join to your house waste. NEVER fix with rigid pipes, never fix the unit to the wall.
DURING BUILD, LIKE ALL SHOWERS CORRECT SEALING IS IMPERATIVE.
ALWAYS FIT "EASY TO GET TO TAP VALVES" ON BOTH HOT AND COLD WATER. THE SAME AS A DISHWASHER OR WASHING MACHINE THIS PRODUCT
SHOULD BE ISOLATED WHEN NOT IN USE.

insigniarange.com Last Modified: 23/01/2014
05
YOU WILL NEED
TOTAL ELECTRICAL REQUIREMENTS
Voltage Rating 220 -240AC
Frequency Rating 0HZ
Power Rating 3.0KW
Your electrical contractor should understand ALL legal requirements of connection before undertaking any work or installation.
UNDER NO CIRCUMSTANCES UNDERTAKE THIS YOURSELF!!!
Note for electrician. This product comes with 13 amp plug(s) fitted with an RCD unit. We leave it this way for you to connect this your own way due to continued additions
to current regulations. As at October 2010 we offered two methods.
1) Connect within current laws and IP directives using plug and RCD provided with steam version or supply one for non steam version
2) (Preferred) Wire into isolated fused feed connecting directly to the house consumer/service box. Remove the fitted plug and ensure the Consumer unit has capabilities to
replace RCD feature if RCD is removed.
Always use protection against electrical surge. Your shower should be treated the same as a home computer. A surge protector should eradicate the possibility of either
the transformer or computer control being burnt out. Please note earth is required and found on chassis of shower tray. A further earth is required from Steam Generator
unit. Each earth must ground through power supply line.
Requirements
Scissors Stanley Blade Silicone Gun S irit Level Ta e Measure Phili s Screwdriver Electric Drill

insigniarange.com Last Modified: 23/01/2014
06
Whilst the next steps show you how to assemble your shower we want to make sure you have a correct build to ensure you get a trouble free shower. Therefore our advice
is to follow the instructions and perform a dry run to ensure you are confident with the build and you understand fully how the unit is assembled. When we use the word
“DRY RUN” this means you do not silicone anything, just simply construct the shower, align, drill and screw everything together. Once you are happy with the build take the
unit apart and carry out the final fix.
Wh t’s In The Boxes?
Tray Box
1x Tray
1x Roof
2x Curved Rails
Glass Room
2x Door seals
1x Glass door
2x fixed glass
Column
1x Complete Column
Backwalls
1x Angled Panel Back all
1x Square Panel Back all
Side Panel
Glass Side Panel
In addition to above you will have all the required internal accessories to com lete the shower

insigniarange.com Last Modified: 23/01/2014
07
VERY IMPORTANT
Have you got everything? If not please contact the Insignia Support Line on 01908 226 4 . Remember NEVER book your tradesman until everything has arrived, been
checked and is present. No replacement/missing parts can be obtained free of charge during or after the build. Any claims can only be within the timescale permitted (48
hours after delivery) and always BEFORE build.
Insigni Screw P ck
VERY IMPORTANT
Have you got everything? If not please contact the Insignia Support Line on 01908 226 4 . Remember NEVER book your tradesman until everything has arrived, been
checked and is present. No replacement/missing parts can be obtained free of charge during or after the build. Any claims can only be within the timescale permitted (48
hours after delivery) and always BEFORE build.
Product Code Descripon Quanty
SP097 Door Handles 1
SP011/012 Door Wheels 2 each
ST20 20mm Screws 20
ST35 35mm Screws 10
ST14 14mm Screws 6
ST25/PCH13/CPC16/B22 arious 14 each
BAG Chrome Brackets 12
DB61 Drill Piece 1

insigniarange.com Last Modified: 23/01/2014
08
Pressure Requirements from your house su ly
We recommend a bar pressure between 2. and 3.4 BAR. If you have a combi boiler system no problem should be experienced. If you have a gravity feed older type
installation (hot water tank type usually less than 1 bar) you will almost certainly need a pump. We cannot advise on which type of pump is used, location or design because
all house plumbing layouts vary. This is a job for your installer/plumber. The end delivery however must fall within the scope above.
Debit Requirements
You will need the debit capabilities of at least 10 litres per minute. Again an average combi boiler will supply this but please check if you have a gravity feed system.
Im ortant Note Do not exceed 3.4 BAR pressure under any circumstances. Warranty is void if so as damage will occur. If you have a combi supply, please use a pressure
reducing valve if required to lower the BAR pressure to the shower.
Please Remember that this product is free standing and is designed to be pulled away from the wall. The water supply and waste require flexible pipes. If you purchased the
fitting kit with this shower you will have the required fittings. The water supply pipes need to be at least 1 metre in length and must be that of a flexi braided type..
DO NOT OVERTIGHTEN IT CAN CAUSE THE CONNECTION TO POP AFTER A FEW WEEKS OF USE
Please note if a shower um is used via gravity system we recommend a se arate cold feed by assing um direct to generator to avoid damage to the
generator.
Further to this as you would with a washing machine or dishwasher, it is highly recommended that accessible water valve taps are installed to turn off the shower when not
In use. This will avoid any possible flooding due to a burst pipe or connection failure in the future.

insigniarange.com Last Modified: 23/01/2014
09
TO START
Make sure you have a clear space, remember when finished and in place you need access
to check your build and able to pull the shower out for servicing or should you have the need
to replace anything!
Take the shower tub and remove all the protective wrapping and fit the waste. If you
purchased the fitting kit it is possible this may have already been fitted in the tray hole yet
please note this is only for transportation reasons therefore you will still need to ensure the
correct sealing and alignment is carried out. In the side of the waste supplied in the optional
fitting kit you will notice a spigot not seen on an ordinary waste. In most cases this is blanked
yet should you have a steam version you need to gently drill this out as this item is for the
steam generator drainage and will be connected in the instructions later.
Now please level the tray by firstly placing the tray in its final location and then using a spirit
level, adjust the tray feet accordingly. Once you are happy with the levelling of the tray, you
can pull it out to begin the main construction.
Ste 1
Run a bead of silicone along the edge and bottom of the large squared
side glass panel and the angled back panel glass and place onto the tub
and screw together using the ST20 screws

insigniarange.com Last Modified: 23/01/2014
10
Ste 3
Now apply silicone to both sides and the bottom of the large square back
glass panel to the column and fix together using the ST20 screws.
Ste 2
Now apply silicone to both sides and the bottom of the control column and place the
next to the angled back glass panel and fix together using the ST20 screws.
(please note, if your column has a rubber seal at the bottom , take the rubber off and apply
silicone inside the rubber and replace)

insigniarange.com Last Modified: 23/01/2014
11
Ste 5
Next using the angled upright, lock this to the rear squared glass panel by
following the position shown in the image marked “1”
Now move the angled upright in the direction as shown in image “1” until this
locks into place as of image “2”
1
2
1
2
1
2
Ste 4
Apply silicone to the angled front glass and now lock the front angled glass
panel to the side glass panel by following the position shown in the image
marked “1”
Once you have met the back panel inside the front upright as per the close
up image walk the panel around to the position shown in the image
marked “2”

insigniarange.com Last Modified: 23/01/2014
12
Ste 6
Lower the top curved rail into position and screw from the rear side as per the
image using the ST35 screws
Ste 7
Now using the ST35 screws, fix the front of the top curved rail onto the upright of the front
fixed angled glass.
Please note in order to do this you will need to slide up the front fixed panel roughly 3
inches to expose the screw holes.
Once secured lower the panel back into position.

insigniarange.com Last Modified: 23/01/2014
13
Ste 8
Now silicone the bottom of the remaining curved rail and place into position as per
image and fix this into place using the ST35 screws
Please note that when drilling the holes to take the screws this is at a depth no deeper than
mm.
Ste 9
Take the front curved glass panel and attach the “U” shape glass seal onto the right hand
side.
Now meet the glass panel onto the curved rails and slide into the upright on the Left hand
side.

insigniarange.com Last Modified: 23/01/2014
14
Ste 10
Insert remaining upright to the left of the curved glass panel. Drill and screw this
into position using the ST14 and once fixed slide the flat rubber glass seal into this
newly fitted upright on the inside (as of the red line in the image)
Please note, ensure you drill no deeper than mm
Ste 11
Pierce through the holes using a screwdriver to show pre-cut holes in the
glass as indicated in the image. Now using the chrome “L” brackets, fix these to the
glass panels using the provided nuts and bolts (B22) please ensure the bolt goes
through the plastic cover holder (PCH13) first
Align the shower panels until you are happy with the sitting of these and now using
the ST25 screws, screw the brackets to the tub
Now place the Chrome cover caps (CPC16) onto the cover holders (PCH13)

insigniarange.com Last Modified: 23/01/2014
15
Ste 12
Pierce through the holes using a screwdriver to show pre-cut holes in the glass as
indicated in the image. Now repeat the process from step 11 to secure the roof to the
glass panels
Ste 13
Align the shower roof to your side panels and when you are happy with the
alignment of the roof, use the ST14 screws to screw this into place

insigniarange.com Last Modified: 23/01/2014
16
x2
Shelf
Fix the chrome floating shelf brackets to your glass back panel by using the provided screws. Now attach the chrome tubed bars to your glass shelf as illustrated in the
below image. Next slide the shelf into your shelf brackets and secure by tightening the grub screw situated on the bottom of the bracket.
Accessory Inst ll tion
Foot Massager
Fix the provided white plastic foot massage retaining knobs to your glass back panel along with your chrome water outlet as shown in the above image. To hang the foot
massager itself to the wall, push the massager onto the retaining knobs ensuring the holes on the underside of the foot massager are aligned.
Please Note
Ensure all grey backing film on the rear of the glass panels are pierced through the existing glass holes
with a knife to provide an efficient smooth fitting and location of the accessories. We recommend using
a screwdriver on the smaller holes.

insigniarange.com Last Modified: 23/01/2014
17
Hand Shower
Attach the chrome riser bar to the glass wall ensuring the water inlet is inserted
through the lower large hole and hand tightened from the rear side.
Now tighten the chrome shower holder ensuring that this will take the hand shower
itself without falling (please note over tightening will prevent the holder from sliding up
and down)
Thermostatic Probe
Insert the probe into the hole situated below the control panel roughly 6mm into the
cabin and run clear silicone around the rear side of the probe
Ozone (o3)
Unscrew the chrome pepper pot end and drop the white box upside down into the
rear hole as shown in the image. Now from the inside of the shower re-attach the
chrome pepper pot end and tighten.
Monsoon Head
Attach the grey hose from your valve to the inner black tube using PTFE tape
(please note this only needs to be hand tight. Over tightening will snap/damage the
inner black tube)
Steam Pod
Insert the pod from the inside of the shower and attach large white nut from the rear.

insigniarange.com Last Modified: 23/01/2014
18
Door Seals
Magnetic Seal: Push the magnetic door seal on the handle side of the glass door ensuring this is
tightly fitted.
Rear Door Seal: Place the rear door seal on the opposite side to the magnetic strip ensuring the flap
is facing the fixed glass panel
Handle
Ensuring that the inner thread is protruding out from the handle far enough, place the handle on the
outside of the door and secure by tightening the inner chrome knob to the protruding inner thread
Door Wheels
Fit the adjustable wheels to the top and bottom of the glass doors and ensure the wheels are facing towards the rail then
hang the top wheels on to the top inner curved rail.
Now on the bottom wheels please push the button to lower the wheel for ease of installation and push the wheel into the
bottom curve rail. Once you are happy that the wheel is in the track, depress the button and allow the wheel to enter
therefore ensuring a secure a tight fit. Next adjust the top wheels by turning the screw clockwise in which in turn will pull the
wheels towards the track ensuring a secure a tight fit.
Now grease the track to ensure a smooth and long lasting operation (not supplied)

insigniarange.com Last Modified: 23/01/2014
19
Shower Valve
Device output may differ from the image. Please refer to your outer chrome faceplate in-
side your Insignia shower as a reference point.
IF YOUR DIAL DOES NOT CORROSPOND TO THE APPROPRIATE DEVICE:
Turn on your water to the shower and note which output the water exits from then turn off
the water and swap over the relevant hose.
Alternatively remove the outer chrome knob by removing the chrome cap and loosening
the grub screw (please ensure not to unscrew fully as this will drop within the chrome
knob) this is found on the opposite side to the chrome pillar. Once you have succeeded in
loosening this you can now slide your faceplate to correspond to the device.
Cold Water In Hot Water In
Steam ut
Bath Connecon
Hand Shower
Top Shower
Foot Massager
Body Jets
Door Seals
Magnetic Seal: Push the magnetic door seal on the handle side of the glass door ensuring this is
tightly fitted.
Rear Door Seal: Place the rear door seal on the opposite side to the magnetic strip ensuring the
Hand Shower
Top Shower
Foot Massager

insigniarange.com Last Modified: 23/01/2014
20
Electric Box/Ste m Gener tor Connections
Fan
Speaker
zone
Light
Light 2
Thermostac Probe
RJ11 Phone Connecon
Radio Aerial AUX Audio In Connecon