Insportline IN 7536 Power Tower PT80 User manual

USER MANUAL –EN
IN 7536 Power Tower inSPORTline PT80

2
CONTENTS
SAFETY INSTRUCTIONS....................................................................................................................... 3
EXPLODED DRAWING........................................................................................................................... 4
PARTS LIST............................................................................................................................................ 5
ASSEMBLY INSTRUCTIONS................................................................................................................. 8
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS................................................. 11

3
SAFETY INSTRUCTIONS
This exercise equipment is built for optimum safety. Be sure to read the entire manual before you
assemble or operate your equipment. Please note the following safety precautions:
1. Keep children and pets away from the equipment at all times. Do not leave children
unattended in the same room with the equipment.
2. Only one person at a time should use the equipment.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms STOP
the workout at once. CONSULT PHYSICIAN IMMEDIATELY.
4. Position the equipment on a clear, level surface. DO NOT use the equipment near water or
outdoors. If necessary, place a protective mat (not included in scope of delivery) to protect
your floor underneath the device and keep a free space of at least 0.6 m around the device for
safety reasons.
5. Always wear appropriate workout clothing when exercising. DO NOT wear robes or other
clothing that could become caught in the equipment.
6. Use the equipment only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
7. Before using the equipment, always do stretching exercises to properly warm up.
8. Never operate the equipment if it is not functioning properly.
9. Maximum user weight: 135 kgs (300 Lbs)
10. Class H(according to EN ISO 20957) for home use.

4
EXPLODED DRAWING

5
PARTS LIST
NO.
Description
01
Base Tube, 2 pcs
02
Bottom Upright, 2 pcs
03
Central Cross Support 1 pc
04
Top Upright, 2 pcs
05
Left Arm Support, 1 pc

6
06
Right Arm Support, 1 pc
07
Lat Bar, 1 pc
08
Back Pad Support, 1 pc
09
Back Pad, 1 pc
10
Arm Pad, 2 pcs
11
Arm Support Handle, 2 pcs

7
12
Angle Support, 2pcs
13
Hex Bolt (M10x70mm), 14 pcs
14
Hex Bolt (M10x60mm), 2 pcs
15
Hex Bolt (M10x20mm), 14pcs
16
Hex Bolt (M8x65mm), 4pcs
17
Hex Bolt (M8x20mm), 2pcs
18
Washer (M10), 46pcs
19
Washer (M8), 6pcs

8
20
Nylon Lock (M10), 16pcs
ASSEMBLY INSTRUCTIONS
STEP 1:
Attach the Bottom upright (02) to Base tube (01)
using 4pcs Hex bolt M10x20mm (15) and 4pcs
Washer Φ10 (18).
STEP 2:
Attach Central cross support (03) to Bottom
upright (02) using 4pcs Hex bolt M10x70mm (13),
8pcs washer Φ10 (18) and 4pcs Nylon lock nut
M10 (20).
Attach Angle support (12) to Bottom upright (02),
and Base tube (01), using 4pcs Hex bolt
M10x70mm (13), 8pcs washerΦ10 (18) and 4pcs
Nylon lock nut M10 (20).

9
STEP 3:
Attach the lat bar (07) to the top upright (04), with
2pcs Hex bolt M10x60mm (14) and 4pcs washer
Φ10 (18) and 2pcs Nylon nut M10 (20).
Insert the Top upright (04) into the Bottom upright
(02), using 4pcs Hex bolt M10x20mm (15) and
4pcs washer Φ10 (18).
STEP 4:
Attach the Left arm support (05) to the Bottom
upright (02) and Top upright (04), using 2pcs Hex
bolt M10x20 (15), 1pc Hex bolt M10x70mm (13),
4pcs washer Φ10 (18) and 1pc Nylon nut M10
(20).
Attach the right arm support (06) to the Bottom
upright (02) and Top upright (04), using 2pcs Hex
bolt M10x20mm (15), 1pc Hex bolt M10x70mm
(13) 4pcs washer Φ10 (18) and 1pc Nylon nut
M10 (20).

10
STEP 5:
Attach the Back pad support (08) to the Left arm
support (05) and Right arm support (06), using
4pcs Hex bolt M10x70mm (13), 8pcs washer
Φ10 (18) and 4pcs Nylon nut M10 (20).
STEP 6:
Insert the Arm support handle (11) into the Left
arm support (05) and Right arm support (06),
using 2pcs Hex bolt M10x20mm (15), and 2pcs
Washer Φ10 (18).