Insportline RK4201 User manual

RK4201
OWNER'S MANUAL
ASSEMBLY INSTRUCTIONS

HARDWARE ILLUSTRATION

PARTS LIST
A-1x N-2x 13-4x-M10*20
LEFT BEAM JOINT TUBE CROSS HEAD BOLT
B-1x 1-1x 14-2x-M10*20
RIGHT BEAM BACK REST BOLT
C-2x 2-2x 15-6x-M10*65
DOWN POST ARM REST BOLT
D-1x 3-4x 16-18x-M10*70
HORIZONTAL
SUPPORT
SQUARE END CAP BOLT
E-2x 4-2x 17-6x-8
DIAGONAL
SUPPORT
PLASTIC BUSHING WASHER
F-2x 5-2x-50*50 18-50x-10
ARM REST
SUPPORT
SQUARE CAP WASHER
G-1x 6-1x-40*20 19-2x-M10
BACK REST
SUPPORT QUADRATE CAP LOCK NUT
H-2x 7-8x-φ25 20-22x-M10
UP POST ROUND CAP NUT
I-1x 8-8x-φ25
FOAM SUPPORT HANDLE FOAM
J-2x 9-2x
DIAGONAL
SUPPORT
Ⅱ
FOAM ROLLER
K-2x 10-2x
HANDLE SUPPORT PIN
L-1x 11-2x-M8*40
PULL BAR BOLT
M-2x 12-4x-M8*70
JOINT PLATE BOLT

ASSEMBLY INSTRUCTIONS
STEP 1
1. Attach square end caps (3) to left beam (A) and
right beam (B). Attach handle support (K) to left
beam (A) and right beam (B) with cross head bolt
M10*20 (13).
2. Slide down posts (C) onto left beam (A) and
right beam (B), screw with two bolts M10*20 (14),
four bolts M10*65 (15), ten washers 10 (18) and
four nuts M10 (20).
3. Attach horizontal support (D) and joint plate (M)
to down posts (C) with four bolts M10*70 (16) and
washers 10 (18) and nuts M10 (20).
4. Attach diagonal support (E) to left beam (A) and
down post (C) with two bolts M10*70 (16) and
washers 10 (18) and nuts M10 (20).
5. Attach diagonal support (E) to right beam (B)
and down post (C) with two bolts M10*70 (16) and
washers 10 (18) and nuts M10 (20).
6. Slide foam rollers (9) onto foam support (I).
7. Attach foam support (I) to horizontal support (D)
with two pin (10).
STEP 2
1. Insert joint tube (N) into down posts (C), screw
with bolt M10*65 (15) and washers 10 (18) and
nuts M10 (20).
2. Attach arm rests (2) to arm rest supports (F) with
bolts M8*70 (12) and washers 8 (17).
3. Attach arm rest supports (F) and back rest
support (G) to down post (C) and up post (H) with
bolts M10*70 (16) and washers 10 (18) and nuts
M10 (20).
4. Attach diagonal support Ⅱ (J) to down posts (C)
and arm rest support (F) with bolts M10*70 (16)
and washers 10 (18) and nuts M10 (20).
5. Attach back rest (1) to back rest support (G) with
bolts M8*40 (11) and washers 8 (17).
STEP 3
1. Attach pull bar (L) to up posts (H), screw with
bolts M10*70 (16) and washers 10 (18) and lock
nuts M10 (19).